The baudclock_locked variable is only used in functions which
are serialized anyway from the core. No need to have a lock
around the variable, so remove it.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-By: NMichael Grzeschik <mgr@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

The fsl_ssi driver uses the .set_sysclk callback to configure the
bitclock for master mode. This is unnecessary since the bitclock
is known in hw_params. This patch configures the bitclock from .hw_params.
.set_dai_sysclk now sets a bitclock frequency which is preferred over
the default calculated bitclock frequency.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-By: NMichael Grzeschik <mgr@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

The simple soundcard binding has its own way for specifying the dai
format. To be able to use this binding we have to make the fsl,mode
property optional. As the property is used in existing devicetrees
keep the option around for compatibility reasons.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-By: NMichael Grzeschik <mgr@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Introduce a SoC data struct which contains the differences between
the different SoCs this driver supports. This makes it easy to support
more differences without having to introduce a new switch/case each
time.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-By: NMichael Grzeschik <mgr@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Doing a suspend/resume sequence while playing an audio track in the backgroung
causes broken audio right after resume:

root@freescale /$ aplay clarinet.wav &

root@freescale /home$ Playing WAVE 'clarinet.wav' : Signed 16 bit Little Endian,
 Rate 44100 Hz, Mono

root@freescale /home$ echo mem > /sys/power/state
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.002 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
PM: suspend of devices complete after 37.082 msecs
PM: suspend devices took 0.040 seconds
PM: late suspend of devices complete after 4.234 msecs
PM: noirq suspend of devices complete after 4.618 msecs
Disabling non-boot CPUs ...
PM: noirq resume of devices complete after 4.013 msecs
PM: early resume of devices complete after 4.000 msecs
PM: resume of devices complete after 68.907 msecs
PM: resume devices took 0.070 seconds
Restarting tasks ... Suspended. Trying resume. Failed. Restarting stream. Done.
Suspended. Trying resume. Failed. Restarting stream. Done.
Suspended. Trying resume. Failed. Restarting stream. Done.
Suspended. Trying resume. Failed. Restarting stream. Done.
Suspended. Trying resume. Failed. Restarting stream. Done.
Suspended. Trying resume. Failed. Restarting stream. Done.
Suspended. Trying resume. Failed. Restarting stream. Done.
....

Add SNDRV_PCM_TRIGGER_RESUME/SUSPEND cases so that we can gracefully handle
system suspend/resume.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NShawn Guo <shawn.guo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

fsl_ssi_set_dai_sysclk will be called from fsl_ssi_hw_params in the
next patch. Move up to avoid forward declaration and to keep the next patch
more readable. No functional change.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-By: NMichael Grzeschik <mgr@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

When the fsl-ssi unit is used in i2s slave mode, it is possible that the
SSI unit starts transmitting data on the wrong channel. This happens
because the SSI does not synchronize with the left-right-clock by
default.

This patch enables transmit enable synchronization.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-By: NMichael Grzeschik <mgr@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

There are some variables defined in struct fsl_ssi_private that describe
states that are also described by other variables.

This patch adds some helper functions that return exactly the same
information based on available variables. This helps to clean up struct
fsl_ssi_private and remove them from the probe function.

It also removes some not really used variables (new_binding, name).
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-By: NMichael Grzeschik <mgr@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Reorder the probe function to be able to move the second imx-specific
block to the seperate imx probe function. The patch also removes some
comments/variables/code that are not used anymore or could be simply
replaced by other variables.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-By: NMichael Grzeschik <mgr@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Simplify dma DT property handling. fsl,ssi-dma-events is not used
anymore. It passes invalid data to imx_pcm_dma_params_init_data() which
copies some data into an imx dma struct. This struct is never used in
imx-dma or imx-sdma because of generic OF DMA handling. The
"fsl,ssi-dma-events" is not used anywhere in dts files.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-By: NMichael Grzeschik <mgr@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Move imx specific probe code to a seperate function. It reduces the
size of the probe() function and makes the code and error handling
easier to understand.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-By: NMichael Grzeschik <mgr@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Instead of creating a name using string manipulation functions, we can
simply use the device name for the DAI driver struct.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-By: NMichael Grzeschik <mgr@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Move all code that is only used for debugging to a seperate file. This
makes it easier to see what functions are used for debugging only.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-By: NMichael Grzeschik <mgr@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

The bits we have to clear when disabling are different when the other
stream is still active.

This patch fixes the calculation of new register values after disabling
one stream. It also adds a more detailed description of the new register
value calculation.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Tested-By: NMichael Grzeschik <mgr@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

In fsl_ssi_hw_params() we update the I2S and NET bits using the i2s_mode
variable. The fsl_ssi_set_dai_fmt() function only writes the i2s-mode to
the i2s_mode variable and not the NET bit. This fixes it by adding that
bit to i2s_mode.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

fsl_ssi_set_dai_fmt() manages most of the register setup routines now.
fsl_ssi_setup() makes the same as fsl_ssi_set_dai_fmt() but it relies on
DT properties.

In most cases the settings of fsl_ssi_setup() are already overwritten by
fsl_ssi_set_dai_fmt() when it is called by the soc-core when a sound
card is added. As these settings depend on the combination of codec and
cpu DAI, this should really be done by sound cards.

This patch removes fsl_ssi_setup() and adds the missing register setups
to fsl_ssi_set_dai_fmt(). It also removes all calls to fsl_ssi_setup().
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

The BCP bit in TCR4/RCR4 register rules as followings:
  0 Bit clock is active high with drive outputs on rising edge
    and sample inputs on falling edge.
  1 Bit clock is active low with drive outputs on falling edge
    and sample inputs on rising edge.

For all formats currently supported in the fsl_sai driver, they're exactly
sending data on the falling edge and sampling on the rising edge.

However, the driver clears this BCP bit for all of them which results click
noise when working with SGTL5000 and big noise with WM8962.

Thus this patch corrects the BCP settings for all the formats here to fix
the nosie issue.
Signed-off-by: NNicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

It's quite cricial to clear error flags because SAI might hang if getting
FIFO underrun during playback (I haven't confirmed the same issue on Rx
overflow though).

So this patch enables those irq and adds isr() to clear the flags so as to
keep playback entirely safe.
Signed-off-by: NNicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch add .xlate_tdm_slot_mask support for IMX SSI, and this
will generate the TDM slot TX and RX masks.
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch add .xlate_tdm_slot_mask support for ESAI, and this will
generate the TDM slot TX and RX masks.
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch add fsl_asoc_xlate_tdm_slot_mask() support for utils.
For the some spcified DAI driver, this will be used to generate the
TDM slot TX/RX mask. And the TX/RX mask will use a 0 bit for an active
slot as default, and the default active bits are at the LSB of
the masks.
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Now that AIC23 supports two control interfaces all existing I2C users
should select I2C variant.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

There is no point in using FIQ if DMA is available (it is selected) and
selecting FIQ currently breaks the build on non-i.MX platforms.  If FIQ
is actually required the build will need to be restricted or have a
select for the relevant FIQ code adding.
Signed-off-by: NMark Brown <broonie@linaro.org>

Use table based setup to register the DAPM widgets and routes.  This on one hand
makes the code a bit shorter and cleaner and on the other hand the board level
DAPM elements get registered in the card's DAPM context rather than in the
CODEC's DAPM context.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Cc: Eric Bénard <eric@eukrea.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: alsa-devel@alsa-project.org
Cc: devicetree@vger.kernel.org
Signed-off-by: NDenis Carikli <denis@eukrea.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

o Add SND_SOC_DAIFMT_DSP_A support.
o Add SND_SOC_DAIFMT_DSP_B support.
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

o Fix some bugs of fsl_sai_set_dai_fmt_tr().
o Add SND_SOC_DAIFMT_LEFT_J support.
o Add SND_SOC_DAIFMT_CBS_CFM support.
o Add SND_SOC_DAIFMT_CBM_CFS support.
o And SND_SOC_DAIFMT_RIGHT_J need to be done in the future.
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Instead of jumping to the 'out' label, just return the error code immediately.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

For most platforms, the CPU and ESAI device is in the same endianess
mode. While for the LS1 platform, the CPU is in LE mode and the ESAI
is in BE mode.
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Acked-by: NNicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

For most platforms, the CPU and SPDIF device is in the same endianess
mode. While for the LS1 platform, the CPU is in LE mode and the SPDIF
is in BE mode.
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Acked-by: NNicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Since the Freescale SAI, ESAI and SPDIF are using the regmap-mmio,
there needs a select of REGMAP_MMIO in the Kconfig to ensure that
regmap-mmio is actually enabled.
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Acked-by: NNicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

The commit 1abe729f (ASoC: fsl: Add missing pm to current machine
drivers) enables pm support for a few IMX machine drivers.  But it does
not update dev drvdata to be the pointer to 'card'.  This causes the
kernel dump below in system suspend, because snd_soc_suspend() expects
that the dev drvdata points to 'card', while it still points to the
private data of machine driver.

This patch fixes imx-sgtl5000 and imx-wm8962 by attaching 'card' to dev
drvdata and private data to card drvdata.  For imx-mc13783, I simply
revert the pm change because it must be broken for the same reason and
I don't have hardware to test pm enabling code.

$ echo mem > /sys/power/state
PM: Syncing filesystems ... done.
PM: Preparing system for mem sleep
mmc1: card e624 removed
Freezing user space processes ... (elapsed 0.002 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done.
PM: Entering mem sleep
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 1861 Comm: bash Not tainted 3.14.0-rc1+ #1648
Backtrace:
[<80012144>] (dump_backtrace) from [<800122e4>] (show_stack+0x18/0x1c)
 r6:8079c77c r5:00000c5a r4:00000000 r3:00000000
[<800122cc>] (show_stack) from [<80637ac0>] (dump_stack+0x78/0x94)
[<80637a48>] (dump_stack) from [<80028918>] (warn_slowpath_common+0x6c/0x8c)
 r4:bdb21c38 r3:be62df00
[<800288ac>] (warn_slowpath_common) from [<800289dc>] (warn_slowpath_fmt+0x38/0x40)
 r8:be62e3a8 r7:bf122960 r6:00000005 r5:00000000 r4:00000000
[<800289a8>] (warn_slowpath_fmt) from [<8006518c>] (__lock_acquire+0x1ae0/0x1ce0)
 r3:8079d598 r2:80799e70
[<800636ac>] (__lock_acquire) from [<80065894>] (lock_acquire+0x68/0x7c)
 r10:bdb20000 r9:be62df00 r8:00000000 r7:00000000 r6:60000013 r5:bdb20000
 r4:00000000
[<8006582c>] (lock_acquire) from [<8063c938>] (mutex_lock_nested+0x5c/0x3b8)
 r7:00000000 r6:80dfc78c r5:804be444 r4:bf122928
[<8063c8dc>] (mutex_lock_nested) from [<804be444>] (snd_soc_suspend+0x34/0x42c)
 r10:00000000 r9:00000000 r8:00000000 r7:bf1c4444 r6:bf1c4410 r5:be978150
 r4:be978010
[<804be410>] (snd_soc_suspend) from [<8034392c>] (platform_pm_suspend+0x34/0x64)
 r10:00000000 r8:00000000 r7:bf1c4444 r6:bf1c4410 r5:803438f8 r4:bf1c4410
[<803438f8>] (platform_pm_suspend) from [<80348e18>] (dpm_run_callback.isra.7+0x34/0x6c)
[<80348de4>] (dpm_run_callback.isra.7) from [<80349354>] (__device_suspend+0x10c/0x220)
 r9:808dd974 r8:808c4a5c r6:00000002 r5:80e5001c r4:bf1c4410
[<80349248>] (__device_suspend) from [<8034a338>] (dpm_suspend+0x60/0x220)
 r7:bf1c4410 r6:808dd90c r5:80e5001c r4:bf1c44c0
[<8034a2d8>] (dpm_suspend) from [<8034a790>] (dpm_suspend_start+0x60/0x68)
 r10:8079a818 r9:00000000 r8:00000004 r7:80dfbe90 r6:80641eec r5:00000000
 r4:00000002
[<8034a730>] (dpm_suspend_start) from [<8006a788>] (suspend_devices_and_enter+0x74/0x318)
 r4:00000003 r3:80dfbe98
[<8006a714>] (suspend_devices_and_enter) from [<8006abd8>] (pm_suspend+0x1ac/0x244)
 r10:8079a818 r8:00000004 r7:00000003 r6:80641eec r5:00000000 r4:00000003
[<8006aa2c>] (pm_suspend) from [<80069a4c>] (state_store+0x70/0xc0)
 r5:00000003 r4:bd85ea40
[<800699dc>] (state_store) from [<80294034>] (kobj_attr_store+0x1c/0x28)
 r10:beb9fe08 r8:00000000 r7:bdb21f78 r6:bd85ea40 r5:00000004 r4:beb9fe00
[<80294018>] (kobj_attr_store) from [<80140f90>] (sysfs_kf_write+0x54/0x58)
[<80140f3c>] (sysfs_kf_write) from [<8014474c>] (kernfs_fop_write+0xc4/0x160)
 r6:bd85ea40 r5:beb9fe00 r4:00000004 r3:80140f3c
[<80144688>] (kernfs_fop_write) from [<800dfa14>] (vfs_write+0xbc/0x184)
 r10:00000000 r9:00000000 r8:00000000 r7:bdb21f78 r6:00500c08 r5:00000004
 r4:be782600
[<800df958>] (vfs_write) from [<800dfe00>] (SyS_write+0x48/0x70)
 r10:00000000 r8:00000000 r7:00000004 r6:00500c08 r5:00000000 r4:be782600
[<800dfdb8>] (SyS_write) from [<8000e800>] (ret_fast_syscall+0x0/0x48)
 r9:bdb20000 r8:8000e9c4 r7:00000004 r6:00500c08 r5:00000004 r4:76eb65e0

Fixes: 1abe729f (ASoC: fsl: Add missing pm to current machine drivers)
Cc: stable@vger.kernel.org
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Acked-by: NNicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Currently everytime we get the following message on boot:

fsl-ssi-dai 202c000.ssi: could not get baud clock: -2

This is not really useful information to get on every boot, so make it a debug
message instead.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Since commit aafa85e7 (ASoC: fsl_ssi: Add DAI master mode support for SSI on
i.MX series) master mode is supported, so update the comments and code to
reflect that.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Symbol MFD_MC13783 always selected by MFD_MC13XXX, so no need
to keep additional symbol.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

SNDRV_PCM_RATE_CONTINUOUS means that all rates (possibly limited to a certain
interval) are supported. There is no need to manually set other rate bits.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>