This patch adds support for the cpuimx27 board from Eukrea and its
baseboard. This change is intended to further remove non-DT support
for this board.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add initial imx6sx-sdb board support with limited devices enabled.
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Two reasons for this rename.  Firstly, it removes the camel case
convention which isn't used by any other platform and secondly it
matches the naming convention for the internal kernel, which can
become annoying when flipping between the two.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

Add initial device tree nodes for EXYNOS5410 SoC and SMDK5410 board.
Signed-off-by: NTarek Dakhran <t.dakhran@samsung.com>
Signed-off-by: NVyacheslav Tyrtov <v.tyrtov@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Adds support for google peach-pi board having the
Exynos5800 SoC.
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The patch adds the dts file for xyref5260 board which
is based on exynos5260 SoC.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add device-tree file for APQ8084-MTP board, which belongs
to the Snapdragon 805 family.
Signed-off-by: NGeorgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: NKumar Gala <galak@codeaurora.org>

Add basic APQ8064 SoC include device tree and support for basic booting on
the IFC6410 board.  Also, keep dtb build list and qcom_dt_match in sorted
order.
Signed-off-by: NKumar Gala <galak@codeaurora.org>

Add device tree for the Amarillo validation board with an AXM5516 SoC.
Signed-off-by: NAnders Berg <anders.berg@lsi.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The i12 tvbox is an A20 based android tvbox, with 512M / 1G RAM, 4G nand flash,
ap6210 or ap6330 sdio wifi + bt (broadcom sdio wifi + uart attached brcm bt),
2USB host ports using USB-A receptacles and a micro-usb receptacle for USB OTG,
and 100Mbit ethernet using an IP101a phy.

The PCB is labelled i12-a20 hence I've named the board i12-a20. It is used
in noname allwinner A20 tv-boxes, which are sometimes sold with Q5 or
QT840A as product name.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The B2020 RevE differs from the other B2020 boards in a few subtle ways;
including the Ethernet reset GPIO which this patch adds support for and
the LED wiring which will follow in a latter patch.  Without supplying
these differences Ethernet and the board LEDs simply will not work.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

B2120 HDK is the reference board for STiH407 SoC.
It has the following characteristics:
 - 1GB DDR3
 - 8GB eMMC / SD-Card slot
 - 32MB NOR Flash
 - 1 x Gbit Ethernet
 - 1 x USB 3.0 port
 - 1 x Mini-PCIe
 - 1 x SATA
 - 1 x HDMI output
 - 1 x HDMI input
 - 1 x SPDIF

This patch only introduces basic functionnalities, such as I2C and UART.
Acked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: NLee Jones <lee.jones@linaro.org>
Acked-by: NPatrice Chotard <patrice.chotard@st.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

The boards have to be sorted in alphanumerical order in the Makefile.

Cc: Olof Johansson <olof@lixom.net>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for VAR-SOM-OM44[1] SODIMM system on module from
Variscite. SoM features a OMAP4460, 1GB RAM, Gigabit Ethernet
(LAN7500) and optional WLAN/BT.

Also add support for VAR-STK-OM44 development board from
Variscite. This kit features a VAR-SOM-OM44 and the carrier board
VAR-OM44CustomBoard[2]. The VAR-STK-OM44 is the same as
VAR-DVK-OM44 but without the LCD display.

omap4-var-stk-om44.dts replace the old and very limited
omap4-var-som.dts.

[1] http://www.variscite.com/products/system-on-module-som/cortex-a9/var-som-om44-cpu-ti-omap-4-omap4460
[2] http://www.variscite.com/products/single-board-computers/var-om44customboardSigned-off-by: NJoachim Eastwood <manabian@gmail.com>
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Adds initial support for the Marvell BG2-Q DMP. The board has 2GB of
memory, an uart activated and what's initially supported by the Marvell
Armada 1500 pro dtsi.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>

Allwinner sunxi support has been split into the various SoCs in Kconfig.
Adapt the new symbols for the device trees.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Let the multiplatform Genmai support boot with the unified DTS.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Now that r7s72100 has CCF support, remove the legacy Genmai reference
Kconfig bits for the non-multiplatform case.

Starting from this commit Genmai board support is always enabled via
CONFIG_MACH_GENMAI, and CONFIG_ARCH_MULTIPLATFORM is used to select
between board-genmai.c and board-genmai-reference.c

The file board-genmai-reference.c can no longer be used together with
the legacy sh-clk clock framework, instead CCF is used.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

add element14s RIoTboard http://www.riotboard.org which is an i.MX6Solo
based design targeted at makers.

Signed-off-by: Iain Paton<ipaton0@gmail.com>
Reviewed-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The PBA-B-01 carrier board can be equipped with either Quad or DualLite/Solo
phyFLEX i.MX6 modules (PFL-A-02).
This moves all common devices into imx6qdl-phytec-pbab01.dtsi. The SoC specific
device trees then just include the pfla01 and pbab01 dtsi files corresponding
to the SoC variant.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This patch adds support for Digi ConnectCore® i.MX51/Wi-i.MX51 SOM
and basic support for the ConnectCore for i.MX51 JumpStart Kit.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add initial Toradex Colibri VF61 board support. Ethernet, UART
and SDHC cards are working. Cache latencies need to be a bit
higher than vf610.dtsi suggests. Those values are validated
by running multiple memory tests.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add support for UART, eSDHC and NAND.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Create DTS files to describe the Marvell OpenRD boards.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1399836639-1918-1-git-send-email-andrew@lunn.chTested-by: NFrancois Lorrain <francois.lorrain@gmail.com>
Acked-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This patch adds the device tree to support Toradex Colibri T30, a
computer on module which can be used on different carrier boards.

The module consists of a Tegra 30 SoC, two PMIC, DDR3L RAM, eMMC,
a LM95245 temperature sensor and an AX88772B USB Ethernet
Controller. Furthermore, there is a STMPE811 and SGTL5000 audio
codec which are not yet supported. Anything that is not self
contained on the module is disabled by default.

The device tree for the Evaluation Board includes the modules
device tree and enables the supported pheripherials of the carrier
board (the Evaluation Board supports almost all of them).
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The APP4 EVB1 development boards embeds an A31, together with some NAND, one SD
card slot, and one SDIO + UART WiFi and Bluetooth chip, a few I2C buses, USB,
and a LCD display.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>

NVIDIA SHIELD is a portable Android console containing a Tegra 4 SoC with
2GB RAM and a 720p panel.

The following hardware is enabled by this device tree: UART, eMMC, USB
(needs external power), PMIC, backlight, joystick, SD card, GPIO keys.

DSI panel, HDMI output, charger, self-powered USB, audio, wifi bluetooth
are not supported yet but might be by future patches (likely in that
order).

Touch panel and sensors will probably never be supported.

Initrd addresses are hardcoded to match the static values used by the
bootloader, since it won't add them for us. All the same, a kernel
command-line is provided to replace the one passed by the
bootloader which is filled with garbage.

NVIDIA SHIELD is typically booted with an appended DTB to avoid
modifications made by the bootloader.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
[swarren, fixed gpio-keys child node sort order, patch description]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The R7 tv-dongle is an A10s based hdmi tv dongle, with 1G RAM, 4G nand flash,
and rtl8189es sdio wifi. It has a standard male hdmi connector, an USB host
port using an USB-A receptacle and a micro-usb receptacle for both power
and USB OTG.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Adds the google peach-pit board dts file which uses
exynos5420 SoC.
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

DRA722 is part of DRA72x family which are single core cortex A15 devices
with most infrastructure IPs otherwise same as whats on the DRA74x family.

So move the cpu nodes into dra74x.dtsi and dra72x.dtsi respectively.

Also add a minimal dra72-evm dts file.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Cc: linux-doc@vger.kernel.org
Cc: devicetree@vger.kernel.org
Acked-by: NArnd Bergmann <arnd@arndb.de>
[tony@atomide.com: updated for Makefile sorting]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for CM-T54 CoM and SBC-T54 board:

http://compulab.co.il/products/computer-on-modules/cm-t54/
http://compulab.co.il/products/sbcs/sbc-t54/

SBC-T54 is a single board computer based on OMAP5432 CPU.
It is implemented with a CM-T54 CoM providing most of the functions,
and SB-T54 carrier board providing connectors and several additional
functions.

Added basic support for:

* PMIC
* LED
* MMC/SD
* eMMC
* USB
* I2C1/4
* SB-T54 and CM-T54 EEPROMs
* RTC
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
[tony@atomide.com: updated for Makefile sorting]
Signed-off-by: NTony Lindgren <tony@atomide.com>

With ARCH_OMAP2PLUS being separated out into OMAP2/3/4/5 etc all the TI device
tree blobs are built no matter the combination of SoCs that are enabled. This
often causes a bunch of irrelevant .dts to be built on a multi platform kernel,
this enables the building of just the ones relevant to the SoCs that are
actually enabled. It also orders the dts file alphabetically.

This also helps to avoid trivial merge conflicts when adding support
for new boards.

[tony@atomide.com: updated the order for am335x and am43x, moved am3517 to omap3]
Signed-off-by: NTony Lindgren <tony@atomide.com>

The SOCrates is a SOCFpga-Cyclone5 based board from EBV.
Add support for it.
Reviewed-by: NPavel Machek <pavel@denx.de>
Signed-off-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: NDinh Nguyen <dinguyen@altera.com>

Add a new sun6i-a31-m9 dts file for the Mele M9 / Mele A1000G Quad. These
HTPCs use the same board in a different case, for more details see:
http://linux-sunxi.org/Mele_M9Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Tegra Note 7 is a consumer tablet embedding a Tegra 4 SoC with 1GB RAM
and a 720p panel.

The following hardware is enabled by this device tree: UART, eMMC, USB
(needs external power), PMIC, backlight, DSI panel, keys.

SD card, HDMI, charger, self-powered USB, audio, wifi, bluetooth are not
yet supported but might be by future patches (likely in that order).

Touch panel, sensors & cameras will probably never be supported.

Pinctrl is not set yet, as the bootloader-provided values allow us to
use the currently supported hardware.

Initrd addresses are hardcoded to match the static values used by the
bootloader, since it won't add them for us. All the same, a kernel
command-line is provided to replace the one passed by the bootloader
which is filled with garbage.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
[treding@nvidia.com: DT fixes, DSI panel support]
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This commit converts the Maxtor Shared Storage II Orion5x platform to
the Device Tree. The only remaining things not converted are PCI and
the special power off method.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: https://lkml.kernel.org/r/1398202002-28530-37-git-send-email-thomas.petazzoni@free-electrons.com
Cc: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This commit converts the LaCie d2 Network platform to the Device Tree.

All devices except LEDs are converted, because the LED code needs a
non-LED GPIO to be set to a given value for the LEDs to work, and this
cannot yet be easily represented in DT.

Also, references to the LaCie Big Disk Network platform are lost,
because this platform apparently has exactly the same hardware support
as the LaCie d2 Network, so their Device Tree files would be
identical.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: https://lkml.kernel.org/r/1398202002-28530-36-git-send-email-thomas.petazzoni@free-electrons.com
Cc: Simon Guinot <sguinot@lacie.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This commit converts the RD-88F5182 platform to the Device Tree. All
devices except the PCI are converted to the Device Tree.

It is worth noting that:

 * The PCI description for the DT case is kept in board-rd88f5182.c.

 * The existing non-DT support in rd88f5182-setup.c is kept as is, in
   order to allow testing of a given platform in both DT and non-DT
   cases. It will ultimately be removed, once we no longer care about
   non-DT support for Orion5x.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: https://lkml.kernel.org/r/1398202002-28530-35-git-send-email-thomas.petazzoni@free-electrons.com
Cc: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Add the initial device tree for the R8A7791 SoC based Henninger board. SCIF0
serial port support is included, so that the serial console can work.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>