This patch converts the rb532 code to use gpio library
and register its gpio chip.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch cleans up headers and regroups informations to
where they should reside. While moving, try to have a
consistant naming for defines.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

We are no longer using setup_serial_port. So just remove it
from the prom code.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When there is only platform device of the same type, id = -1
should be used, fix this.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch replaces a raw read using volatiles
with a readl.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

We are no longer using gpio bootup state, so do not export
it and do not parse the kernel command line tag for it.
Instead we provide gpio-keys for the button the gpio bootup
state was checking.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch fixes the misuse of virtual addresses for the GPIO and third
device controller which would lead to problems while accessing ioremap'd
registers.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch moves GPIO related definitions to gpio.h and IRQ
related to irq.h
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Setup default board_be_handler for TX4927/TX4938.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add default machine_restart routine using watchdog reset of TX4927 and
TX4938.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Helper routines in txx9/rbtx4938/spi_eeprom.c is not TX4938 specific.
Move it to txx9/generic/ directory and make it works with SPI bus
number other than 0.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 create mode 100644 arch/mips/txx9/generic/spi_eeprom.c
 delete mode 100644 arch/mips/txx9/rbtx4938/spi_eeprom.c

Add TOSHIBA_RBTX4938_MPLEX_KEEP to keep MPLEX settings by firmware.
Also replace some printk with pr_info.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add helper routines to register physmap-flash platform devices for NOR
flashes.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add kernel options to control bus timeout error.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

TX39/TX49 can enable/disable I/D cache at runtime.  Add kernel options
to control them.  This is useful to debug some cache-related issues,
such as aliasing or I/D coherency.  Also enable CWF bit for TX49 SoCs.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

* Select board by command-line option or firmware environment variable.
* Handle "masterclk=" option.
* Add boards.h to centerize board_vec declaration.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 create mode 100644 include/asm-mips/txx9/boards.h

Add prom_getenv() which can be used for YAMON.  This assumes other
firmware should pass NULL for fw_arg2.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

* Make prom_init_cmdline() static and be called from prom_init.
* Append built-in args if the first character was '+'.
* Drop command-line args if the first character of built-in was '-'.
* Enclose args include spaces by quotes.
* TX4938_NAND_BOOT is no longer needed.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

* Make sure all interrupts cleared on startup
* Initialize some GPIOs
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This new gpio driver for PMC-Sierra's MSP71xx SoC allows
standard api calls for access to the general and extended
gpio's.
Signed-off-by: NPatrick Glass <patrickglass@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 create mode 100755 arch/mips/pmc-sierra/msp71xx/gpio.c
 create mode 100755 arch/mips/pmc-sierra/msp71xx/gpio_extended.c
 create mode 100755 include/asm-mips/pmc-sierra/msp71xx/gpio.h

This replaces mips's sys_ptrace32 with a compat_arch_ptrace and
enables the new generic definition of compat_sys_ptrace instead.
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Symbol name spaghetti which is too complicated to cleanup on this stage
of the release cycle breaks the build on BCM1480 platforms.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Because sync-r4k.c doesn't build.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The Swarm IDE driver uses a release method which is defined in the driver
itself thus potentially oopsable.  The simple fix would be to just leak
the device but this patch goes the full length and moves the entire
handling of the platform device in the platform code and retains only
the platform driver code in drivers/ide/mips/swarm.c.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
[bart: remove no longer needed BLK_DEV_IDE_SWARM from ide/Kconfig]
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Rework of SMTC support to make it work with the new clock event system,
allowing "tickless" operation, and to make it compatible with the use of
the "wait_irqoff" idle loop.  The new clocking scheme means that the
previously optional IPI instant replay mechanism is now required, and has
been made more robust.
Signed-off-by: NKevin D. Kissell <kevink@paralogos.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NKevin D. Kissell <kevink@paralogos.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NKevin D. Kissell <kevink@paralogos.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Though from a hardware perspective it would be sensible to use only a
32-bit unsigned int type Linux defines interrupt flags to be stored in
an unsigned long and nothing else.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch defines pcibios_map_irq() and pcibios_plat_dev_init() for
the BCM47xx platform.

It fixes the regression introduced by commit
aab547ce.
Signed-off-by: NAurelien Jarno <aurelien@aurel32.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

pcibios_map_irq is no way of returning an error but on IP27 an interrupt
is possibly not routable when running out of resources.  So do the
interrupt routing at pcibios_enable_device time.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

David Brownell <david-b@pacbell.net> wrote:
>       The problem is that "value" is zero-or-nonzero.
>       This code wrongly assumes it's zero-or-one.
>       Possible fix:  "((!!value) << gpio)".
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

On the x86 arch, user space single step exceptions should be ignored
if they occur in the kernel space, such as ptrace stepping through a
system call.

First check if it is kgdb that is executing a single step, then ensure
it is not an accidental traversal into the user space, while in kgdb,
any other time the TIF_SINGLESTEP is set, kgdb should ignore the
exception.

On x86, arm, mips and powerpc, the kgdb_contthread usage was
inconsistent with the way single stepping is implemented in the kgdb
core.  The arch specific stub should always set the
kgdb_cpu_doing_single_step correctly if it is single stepping.  This
allows kgdb to correctly process an instruction steps if ptrace
happens to be requesting an instruction step over a system call.
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>

When setting the direction of one GPIO pin we have to keep the state of the
other pins, hence use binary OR. Also gpio_direction_output() wants to set an
initial value, so add that too.

This fixes a problem with the USB power switch on mtx-1 boards.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The -ffunction-sections puts each text in .text.function_name section.
Without this patch, most functions are placed outside _text..._etext
area and it breaks show_stacktrace(), etc.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

If an interrupt happened between checking of NEED_RESCHED and WAIT
instruction, adjust EPC to restart from checking of NEED_RESCHED.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>