dev_dbg() and dev_err() cannot be used to report failures
that may have been caused by a device's removal
Signed-off-by: NOliver Neukum <neukum@b1-systems.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

While an available response is read the device must not
be autosuspended. This requires a flag dedicated to that
purpose.
Signed-off-by: NOliver Neukum <neukum@b1-systems.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Unify mutexes to fix a race between write and disconnect
and shift the test for disconnection to always report it.
Signed-off-by: NOliver Neukum <neukum@b1-systems.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

... and avoid a compilation if we disable host side
of musb.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The recent commit "usb: musb: Add context save and restore support" added
some stubs for the Blackfin code so things would compile, but it also
added a bunch of warnings due to missing return statements.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The USB PHY on current Blackfin processors is a UTMI+ level 2 PHY.
However, it has no ULPI support - so there are no registers at all.
That means accesses to ULPI_BUSCONTROL have to be abstracted away
like other MUSB registers.

This fixes building for Blackfin parts again.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

CONFIG_ARCH_OMAP34XX is now CONFIG_ARCH_OMAP3.

But since drivers/usb/musb/omap2430.c use CONFIG_PM for these
registers and functions, do the same for the header.

Otherwise we get the following for most omap3 defconfigs:

drivers/usb/musb/omap2430.c:261: error: expected identifier or '(' before 'do'
drivers/usb/musb/omap2430.c:261: error: expected identifier or '(' before 'while'
drivers/usb/musb/omap2430.c:268: error: expected identifier or '(' before 'do'
drivers/usb/musb/omap2430.c:268: error: expected identifier or '(' before 'while'
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

C file uses IS_ERR and PTR_ERR, but doesn't include <linux/err.h>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The name used in the documentation doesn't match reality.
Signed-off-by: NOliver Neukum <neukum@b1-systems.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NNathaniel McCallum <nathaniel@natemccallum.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NNathaniel McCallum <nathaniel@natemccallum.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NNathaniel McCallum <nathaniel@natemccallum.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a patch to ftdi_sio_ids.h and ftdi_sio.c that adds identifiers for
CONTEC USB serial converter.  I tested it with the device COM-1(USB)H

[akpm@linux-foundation.org: keep the VIDs sorted a bit]
Signed-off-by: NDaniel Sangorrin <daniel.sangorrin@gmail.com>
Cc: Andreas Mohr <andi@lisas.de>
Cc: Radek Liboska <liboska@uochb.cas.cz>
Cc: stable <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When a signal interrupts a Configure Endpoint command, the cmd_completion used
in xhci_configure_endpoint() is not re-initialized and the
wait_for_completion_interruptible_timeout() will return failure. Initialize
cmd_completion in xhci_configure_endpoint().
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Naming consistency with other USB HCDs.
Signed-off-by: NAlex Chiang <achiang@hp.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The recent commit "usb: musb: Fix for isochronous IN transfer" (f82a689f)
seems to have been against an older kernel version.  It uses the old style
naming of variables.  Unfortunately, this breaks building for most MUSB
users out there since "bDesiredMode" has been renamed to "desired_mode".
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds various USB device IDs for Gobi 2000 devices, as found in the
drivers available at https://www.codeaurora.org/wiki/GOBI_ReleasesSigned-off-by: NBernhard Rosenkraenzer <bero@arklinux.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Stupid logic bug passing a just nulled pointer
Signed-off-by: NOliver Neukum <neukum@b1-systems.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The EHCI driver stores in usb_host_endpoint.hcpriv a pointer to either
an ehci_qh or an ehci_iso_stream structure, and uses the contents of the
hw_info1 field to distinguish the two cases.

After ehci_qh was split into hw and sw parts, ehci_iso_stream must also
be adjusted so that it again looks like an ehci_qh structure.

This fixes a NULL pointer access in ehci_endpoint_disable() when it
tries to access qh->hw->hw_info1.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Reported-by: NColin Fletcher <colin.m.fletcher@googlemail.com>
Cc: stable <stable@kernel.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When isochronous URBs are shorter than one frame and when more than one
ITD in a frame has been completed before the interrupt can be handled,
scan_periodic() completes the URBs in the order in which they are found
in the descriptor list.  Therefore, the descriptor list must contain the
ITDs in the correct order, i.e., a new ITD must be linked in after any
previous ITDs of the same endpoint.

This should fix garbled capture data in the USB audio drivers.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Reported-by: NColin Fletcher <colin.m.fletcher@googlemail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I found a DLink DWM 652 U5 USB 3G modem has product ID 0xce1e instead
of orignal 0xce16. The new ID is added.

And I found there are two entries for 0xce16, one has raw number, the
other has symbol DLINK_PRODUCT_DWM_652_U5. This is fixed too.
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

SL11R-IDE 2.6c (at least) reports wrong capacity (one sector more).
Reading that last sector causes the device not to work anymore (and looks
like HAL or something does that automatically after plugging in):
sd 5:0:0:0: [sdc] Device not ready
sd 5:0:0:0: [sdc] Result: hostbyte=0x00 driverbyte=0x08
sd 5:0:0:0: [sdc] Sense Key : 0x2 [current]
sd 5:0:0:0: [sdc] ASC=0x0 ASCQ=0x0
sd 5:0:0:0: [sdc] CDB: cdb[0]=0x28: 28 00 04 a8 b5 70 00 00 01 00

Add unusual_devs entry to fix the capacity.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

It is possible to have a multi-port device with a port lacking an in or
out bulk endpoint. Only checking for num_bulk_in or num_bulk_out is thus not
sufficient to determine whether a specific port has an in or out bulk
endpoint.

This fixes potential null pointer dereferences in the generic open and
write routines, as well as access to uninitialised fifo in write_room
and chars_in_buffer.

Also let write fail with ENODEV (instead of 0) on missing out endpoint
(also on zero-length writes).
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Make sure usb_serial_port_softint is called on errors also when using
multi urb writes.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Resubmitting read urb fails with -EPERM if completion handler runs while
urb is being killed on close. This should not be reported as an error.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1352) fixes a bug in the way isochronous input data is
returned to userspace for usbfs transfers.  The entire buffer must be
copied, not just the first actual_length bytes, because the individual
packets will be discontiguous if any of them are short.
Reported-by: NMarkus Rechberger <mrechberger@gmail.com>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (34 commits)
  ACPI: processor: push file static MADT pointer into internal map_madt_entry()
  ACPI: processor: refactor internal map_lsapic_id()
  ACPI: processor: refactor internal map_x2apic_id()
  ACPI: processor: refactor internal map_lapic_id()
  ACPI: processor: driver doesn't need to evaluate _PDC
  ACPI: processor: remove early _PDC optin quirks
  ACPI: processor: add internal processor_physically_present()
  ACPI: processor: move acpi_get_cpuid into processor_core.c
  ACPI: processor: export acpi_get_cpuid()
  ACPI: processor: mv processor_pdc.c processor_core.c
  ACPI: processor: mv processor_core.c processor_driver.c
  ACPI: plan to delete "acpi=ht" boot option
  ACPI: remove "acpi=ht" DMI blacklist
  PNPACPI: add bus number support
  PNPACPI: add window support
  resource: add window support
  resource: add bus number support
  resource: expand IORESOURCE_TYPE_BITS to make room for bus resource type
  acpiphp: Execute ACPI _REG method for hotadded devices
  ACPI video: Be more liberal in validating _BQC behaviour
  ...

Commit 6992f533 ("sysfs: Use one lockdep
class per sysfs attribute.") introduced this requirement.  First, at25
was fixed manually.  Then, other occurences were found with coccinelle
and the following semantic patch.  Results were reviewed and fixed up:

    @ init @
    identifier struct_name, bin;
    @@

    	struct struct_name {
    		...
    		struct bin_attribute bin;
    		...
    	};

    @ main extends init @
    expression E;
    statement S;
    identifier name, err;
    @@

    (
    	struct struct_name *name;
    |
    -	struct struct_name *name = NULL;
    +	struct struct_name *name;
    )
    	...
    (
    	sysfs_bin_attr_init(&name->bin);
    |
    +	sysfs_bin_attr_init(&name->bin);
    	if (sysfs_create_bin_file(E, &name->bin))
    		S
    |
    +	sysfs_bin_attr_init(&name->bin);
    	err = sysfs_create_bin_file(E, &name->bin);
    )
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Merge branches 'battery-2.6.34', 'bugzilla-10805', 'bugzilla-14668', 'bugzilla-531916-power-state', 'ht-warn-2.6.34', 'pnp', 'processor-rename', 'sony-2.6.34', 'suse-bugzilla-531547', 'tz-check', 'video' and 'misc-2.6.34' into release

There's no real need for a pointer to the MADT to be global. The only
function who uses it is map_madt_entry.

This allows us to remove some more ugly #ifdefs.
Acked-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Un-nest the if statements for readability.

Remove comments that re-state the obvious.

Change the control flow so that we no longer need a temp variable.
Acked-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Untangle the nested if conditions to make this function look
more similar to the other map_*apic_id() functions.
Acked-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Untangle the if() statement a little for readability.
Acked-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Now that the early _PDC evaluation path knows how to correctly
evaluate _PDC on only physically present processors, there's no
need for the processor driver to evaluate it later when it loads.

To cover the hotplug case, push _PDC evaluation down into the
hotplug paths.

Cc: x86@kernel.org
Cc: Tony Luck <tony.luck@intel.com>
Acked-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Now that we check for physically present processors before blindly
evaluating _PDC, we no longer need to maintain a DMI opt-in table
nor a kernel param.
Acked-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Detect if a processor is physically present before evaluating _PDC.

We want this because some BIOS will provide a _PDC even for processors
that are not present. These bogus _PDC methods then attempt to load
non-existent tables, which causes problems.

Avoid those bogus landmines.
Acked-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Enumerating processors (via MADT/_MAT) belongs in the processor core,
which is always built-in, rather than living in the processor driver
which may not be built.
Acked-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Rename static get_cpu_id() to acpi_get_cpuid() and export it.

This change also gives us an opportunity to remove the
#ifndef CONFIG_SMP from processor_driver.c and into a header file
where it properly belongs.
Acked-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

We've renamed the old processor_core.c to processor_driver.c, to
convey the idea that it can be built modular and has driver-like
bits.

Now let's re-create a processor_core.c for the bits needed
statically by the rest of the kernel. The contents of processor_pdc.c
are a good starting spot, so let's just rename that file and
complete our three card monte.
Acked-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

The ACPI processor driver can be built as a module. But it has
pieces of code that should always be built statically into the
kernel.

The plan is for processor_core.c to contain the static bits while
processor_driver.c contains the module-like bits.

Since the bulk of the code in the current processor_core.c is
module-like, first step is to rename the file to processor_driver.c

Next step will re-create processor_core.c and cherry-pick out
the static bits.
Acked-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NLen Brown <len.brown@intel.com>