Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The follwing commit breaks SH-Mobile on non-ARM platforms:
"8a77b8d0 serial: sh-sci: Support ARM-based SH-Mobile CPUs."

The commit assumed that CONFIG_ARCH_SHMOBILE only was set
on ARM platforms, but it turns out that this kconfig is also
set by all SH-based SoCs. Sh7724 and other older SH-Mobile
SoCs are all broken without this fix.

This patch converts the "defined(CONFIG_ARCH_SHMOBILE)" into
one "defined()" per SoC model - similar to existing SH code.
Reported-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Print the CPU associated with the error only when the field is valid.

Cc: <stable@kernel.org> # .32.x .33.x
Signed-off-by: NBorislav Petkov <borislav.petkov@amd.com>

The console port could have been hot-unplugged. Check if it is valid
before working on it.
Signed-off-by: NAmit Shah <amit.shah@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

When the host lets us know what 'name' a port is assigned, we create the
sysfs 'name' attribute. Generate a 'change' event after this so that
udev wakes up and acts on the rules for virtio-ports (currently there's
only one rule that creates a symlink from the 'name' to the actual char
device).
Signed-off-by: NAmit Shah <amit.shah@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

There is no need to adjust the next rx descriptor after each packet,
so do it only once at the end of the routine.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>

Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clean up some text output formatting.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The recovery from PF reset works better when you shorten up the delay
until the watchdog task executes.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The counters in the 82599 Virtual Function are not clear on read.  They
accumulate to the maximum value and then roll over.  They are also not
cleared when the VF executes a soft reset, so it is possible they are
non-zero when the driver loads and starts.  This has all been accounted
for in the code that keeps the stats up to date but there is one case
that is not.  When the PF driver is reset the counters in the VF are
all reset to zero.  This adds an additional accounting overhead into
the VF driver when the PF is reset under its feet.  This patch adds
additional counters that are used by the VF driver to accumulate and
save stats after a PF reset has been detected.  Prior to this patch
displaying the stats in the VF after the PF has reset would show
bogus data.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As per Simon Horman's feedback set IXGBE_RSC_CB(skb)->dma to zero
after unmapping HWRSC DMA address to avoid double freeing.
Signed-off-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently netdev_features_change is called before fcoe tx queues
setup is done, so this patch moves calling of netdev_features_change
after tx queues setup is done in ixgbe_init_interrupt_scheme, so
that real_num_tx_queues is updated correctly on each fcoe enable
or disable.

This allows additional fcoe queues updated correctly in vlan driver
for their correct queue selection.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The content was deleted in cc87edb1,
but the file remained as a zero-length file.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

cdc_do_config() had a double ret check after fsg_add().
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

fix the problem that when a USB hub is attached to the r8a66597-hcd and
a device is removed from that hub, it's likely that a kernel panic follows.
Reported-by: NMarkus Pietrek <Markus.Pietrek@emtrion.de>
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The xHCI hardware can only handle polling intervals that are a power of
two.  When we add a new endpoint during a bandwidth allocation, and the
polling interval is rounded down to a power of two, print the original
polling interval in the endpoint descriptor.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB 3 and Wireless USB specify a logarithmic encoding of the endpoint
interval that matches the USB 2 specification.  usb_fill_int_urb() didn't
know that and was filling in the interval as if it was USB 1.1.  Fix
usb_fill_int_urb() for SuperSpeed devices, but leave the wireless case
alone, because David Vrabel wants to keep the old encoding.

Update the struct urb kernel doc to note that SuperSpeed URBs must have
urb->interval specified in microframes.

Add a missing break statement in the usb_submit_urb() interrupt URB
checking, since wireless USB and SuperSpeed USB encode urb->interval
differently.  This allows xHCI roothubs to actually register with khubd.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch removes a double usb_control_msg that sets the cp210x
configuration registers a second time when calling cp210x_set_config.
For data sizes >2 the second write gets corrupted.
The patch has been created against 2.6.34-rc1, but all cp210x driver
revisions are affected.
Signed-off-by: NMichael Brunner <mibru@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

One last bit was missed while removing the USB_BERRY_CHARGE config
option in a8d4211f which gets dropped
by this patch.
Signed-off-by: NChristoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This prevents some drivers from complaining that no bcdDevice id was set.
Signed-off-by: NMaurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The change_speed() function should be serialized against multiple calls.
Use the cfg_lock mutex to do this.
Signed-off-by: NAlessio Igor Bogani <abogani@texware.it>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Kconfig help message for Mass Storage Gadget claimed the
module will be named "g_file_storage" whereas it should be
"g_mass_storage".
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Contrary to the comment in fsg_add, fsg_bind calls fsg_unbind on errors,
which decreases refcount and frees the fsg_dev structure, causing trouble
when fsg_add does the same.

Fix it by simply leaving up cleanup to fsg_add().
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Acked-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The recent commit (0e530b45) that moved usb_ep_autoconfig from the
__devinit section to the __init section missed the mass storage device.
Its fsg_bind() function uses the usb_ep_autoconfig() function from non
__init context leading to:
WARNING: drivers/usb/gadget/g_mass_storage.o(.text): Section mismatch in
	reference from the function _fsg_bind()
	            to the function .init.text:_usb_ep_autoconfig()

So move fsg_bind() into __init as well.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The recent change to clean out dead gadget drivers (90f79768)
missed the call to gadget_is_musbhsfc() behind CONFIG_BLACKFIN.  This
causes Blackfin gadget builds to fail since the function no longer
exists anywhere.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

"dev" is always null here.  In the end it's only used to get the
pci_name() of "pdev" which is redundant information and so I
removed it.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Nspark <spark@bandrich.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The module is called qcaux and not moto_modem. Also use help instead of
---help-- to be in sync with the other Kconfig entries.
Signed-off-by: NStefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The new runtime PM scheme allows resume() to have no locks.
This fixes the deadlock.
Signed-off-by: NOliver Neukum <neukum@b1-systems.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- as the callback can schedule work, URBs must be killed first
- if the driver causes an autoresume, the caller must handle locking
Signed-off-by: NOliver Neukum <neukum@b1-systems.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The guarding flag must be set and tested under spinlock
and cleared before the URBs are resubmitted in resume.
Signed-off-by: NOliver Neukum <neukum@b1-systems.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There's a window under which cdc-wdm may submit
an URB to a device about to be suspended. This
introduces a flag to prevent it.
Signed-off-by: NOliver Neukum <neukum@b1-systems.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

dev_dbg() and dev_err() cannot be used to report failures
that may have been caused by a device's removal
Signed-off-by: NOliver Neukum <neukum@b1-systems.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

While an available response is read the device must not
be autosuspended. This requires a flag dedicated to that
purpose.
Signed-off-by: NOliver Neukum <neukum@b1-systems.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Unify mutexes to fix a race between write and disconnect
and shift the test for disconnection to always report it.
Signed-off-by: NOliver Neukum <neukum@b1-systems.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

... and avoid a compilation if we disable host side
of musb.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The recent commit "usb: musb: Add context save and restore support" added
some stubs for the Blackfin code so things would compile, but it also
added a bunch of warnings due to missing return statements.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The USB PHY on current Blackfin processors is a UTMI+ level 2 PHY.
However, it has no ULPI support - so there are no registers at all.
That means accesses to ULPI_BUSCONTROL have to be abstracted away
like other MUSB registers.

This fixes building for Blackfin parts again.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

CONFIG_ARCH_OMAP34XX is now CONFIG_ARCH_OMAP3.

But since drivers/usb/musb/omap2430.c use CONFIG_PM for these
registers and functions, do the same for the header.

Otherwise we get the following for most omap3 defconfigs:

drivers/usb/musb/omap2430.c:261: error: expected identifier or '(' before 'do'
drivers/usb/musb/omap2430.c:261: error: expected identifier or '(' before 'while'
drivers/usb/musb/omap2430.c:268: error: expected identifier or '(' before 'do'
drivers/usb/musb/omap2430.c:268: error: expected identifier or '(' before 'while'
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

C file uses IS_ERR and PTR_ERR, but doesn't include <linux/err.h>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>