Enable 83xx virtual NIC mode
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flash template provides instructions to stop, restart and initalize the
firmware. These instructions are abstracted as a series of read, write and
poll operations on hardware registers. Register information and operation
specifics are not exposed to the driver. Driver reads the template from
flash and executes the instructions located at pre-defined offsets.

Template based firmware reset recovery and initialization mechanism minimize
driver changes as firmware evolves.
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Inter Driver Communication (IDC) module.
CNA function drivers(ISCSI, FCOE and NIC) which shares the adapter
relies on IDC mechanism for gracefull shut down, restart and
firmware error recovery.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

83xx adapter flash memory map, data structures and interface routines
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add 83xx sysfs interface routines
Update 82xx sysfs interface routines
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable base 83xx adapter driver.

Common driver interface routines like probe,
interface up/down routines, irq and resource
allocation routines are modified to add support for 83xx
adapter.
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NSritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add 83xx adapter data path routines
Update few 82xx adapter data path routines
Modify datapath resource allocation routines
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NSritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

83xx adapter register map.
83xx hardware interface routines.
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NSritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactor 82xx driver to support new adapter - Qlogic 83XX CNA

Create adapter abstraction layer and seperate 82xx hardware access routines.
Create mailbox based HW interface mechanism
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactor 82xx driver to support new adapter
Update routines to support variable number of NIC partitions
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cleanup get board information API.
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactor 82xx driver to support new adapter
Update PCI and hardware access routines
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move HW specific data to a seperate structure as part of
refactoring 82xx adapter driver.
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add 82xx adapter ID check before 82xx specific operations as part of
refactoring the driver to enable support for new adapter.
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Physical refactoring of 82xx adapter register dump utility.

Move register dump routines to new file qlcnic_minidump.c
Existing register dump routines has coding style issues, the code
is moved to the new file without fixing the style issues.

There is a seperate patch to fix the style issues in qlcnic_minidump.c
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Physical refactoring of 82xx adapter sysfs routines.

Move sysfs routines to new file qlcnic_sysfs.c
Existing sysfs routines has coding style issues, this code is
moved to the new file without fixing the style issues.

There is a seperate patch to fix the style issues in qlcnic_sysfs.c
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Physical refactoring of 82xx adapter data path routines.

Move data path code to new file qlcnic_io.c
Existing data path code has coding stye issues, the code is
moved to the new file without fixing the style issues.

There is a seperate patch to fix the style issues in qlcnic_io.c
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the following warnings:

qlcnic_main.c: In function 'qlcnic_update_cmd_producer':
qlcnic_main.c:119:51: warning: unused parameter 'adapter' [-Wunused-parameter]
qlcnic_main.c:119: warning: unused parameter adapter
qlcnic_init.c: In function qlcnic_process_lro
qlcnic_init.c:1586: warning: unused parameter sds_ring
qlcnic_init.c: In function qlcnic_process_rcv_diag
qlcnic_init.c:1854: warning: unused parameter sds_ring
qlcnic_init.c: In function qlcnic_fetch_mac
qlcnic_init.c:1938: warning: unused parameter adapter

warning: 'pci_using_dac' may be used uninitialized in this function [-Wmaybe-uninitialized]
qlcnic_main.c:1569:10: note: 'pci_using_dac' was declared here
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Use correct l3 (ETH_IP or ETH_IPV6)protcol in case
of inband vlan. Because of incorrect protcol type driver
was setting incorrect opcode. This resulted in adapter calculating
checksum incorrectly.
o Updated driver version to 5.0.29
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add debug messages for FW CDRP command failure.
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Linux stack estimates MSS from skb->len or skb_shinfo(skb)->gso_size.
In case of LRO skb->len is aggregate of len of number of packets hence MSS
obtained using skb->len would be incorrect. Incorrect estimation of recv MSS
would lead to delayed acks in some traffic patterns (which sends two or three
packets and wait for ack and only then send remaining packets). This leads to
drop in performance. Hence we need to set gso_size to MSS obtained from firmware.

o This is fixed recently in firmware hence the MSS is obtained based on
capability. If fw is capable of sending the MSS then only driver sets the gso_size.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o 0x3, 0x7, 0xF, 0x1F, 0x3F, 0x7F and 0xFF are the allowed capture masks.
o Updated driver version to 5.0.28
Signed-off-by: NManish chopra <manish.chopra@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Without failing probe, register netdevice when device is in FAILED state.
o Device will come up with minimum functionality.
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

 - After FW reset, IP addresses need to be reprogrammed to FW for LRO to work. This
   was not happening in context reset path. Fixed it here.
 - Updated driver version to 5.0.27
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Log dump status.
Remove unmatched qlcnic_api_unlock call.
Update version to 5.0.26.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

v2:	add couple missing conversions in drivers
	split unexporting netdev_fix_features()
	implemented %pNF
	convert sock::sk_route_(no?)caps
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Updated version number to 5.0.25

o Do not hold onto RESETTING_BIT for entire duration of LED/ beacon test.
  Instead, just checking for RESETTING_BIT not set before sending config_led
  command down to card.

o Take rtnl_lock instead of RESETTING_BIT for beacon test while sending
  config_led command down to make sure interface cannot be brought up/ down.

o Allocate and free resources if interface is down before
  sending the config_led command. This is to make sure config_led
  command sending doesn't fail.

o Clear QLCNIC_LED_ENABLE bit if beacon/ LED test fails to start.
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Argument list to CDRP function has become unmanageably long. Fix it by properly
declaring a struct that encompasses all the input and output parameters.
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Beacon test flashes both port LEDs instead of just 1 LED of a port.
Updated driver version to 5.0.23.
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reading CRB registers(if reqd) before releasing the api lock.
Signed-off-by: NSritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The FLT entry for FW image region has changed for C0 cards.
Updated the driver to look at the right region in the FLT.
Signed-off-by: NSritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moves the QLogic drivers into drivers/net/ethernet/qlogic/ and
the necessary Kconfig and Makefile changes.

CC: Ron Mercer <ron.mercer@qlogic.com>
CC: Amit Kumar Salecha <amit.salecha@qlogic.com>
CC: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>

Now printing states of essential registers once fw hang has been detected.
Bumped up the driver version to 5.0.22
Signed-off-by: NSritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver should not check for heart beat anymore when FW is hung, rather it
should restart the FW.
Signed-off-by: NSritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Added code to support FW reset without invoking the dump
o Fixed the return value of the dump data size if dump is not available.
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Change FW dump capture mask to a defult value, instead of using the recommended
  value from the FW. This was done to keep the capture mask consistent with other
  function drivers.

o Update driver version to 5.0.21
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Defined error code such as fw not responding, test already running and
  cable not connected.
o Check Fw capability before performing loopback test.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>