Addresses were changed for a000 devices.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

As preparation for a000 different queue management, separate
mapping of queues from actual enablement.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Now that transport inits the paging in the context info -
remove the call in mvm.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In case of a MFUART assert, get a notification from the fw
that consists of the assert id and debug data.

The notification may be divided to multiple chunks, depending
on the size of the debug data sent to the driver, which would
be up to 1KB.

Get the notification, and if the debug info flag is enabled,
print the debug data to the dmesg.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In a000 devices FW will assign the queue number. Prepare for
that by getting rid of static defines and store them in variables.
Enlarge to u16 since we may have up to 512 queues.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Currently we release up to the last expired frame.
However, if there are consecutive frames after it - we can
optimize it further and release them as well - until the next
hole.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The command was changed to support PN offload and TKIP offload.
The FW will do TKIP calculations in D0 only for a000 devices,
but API is aligned anyway.
However, for all devices we can stop sending the wowlan tkip
command.
Firmware will fetch the keys from the station key command.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Currently multicast queue is associated with the broadcast
station.

This raises quite a few issues:

The multicast queue has a special treatment:
- It is sent in the MAC context command
- It is excluded from tfd_queue_mask

In DQA mode we end up enabling two queues - the probe response
queue and the multicast queue - with the same station (broadcast)
and TID while in DQA mode it should be unique RA-TID.
Firmware will enforce it for a000 devices, so this allocation
will fail.

In addition, in a000 devices the FW will set the FIFO and not
the driver. So there is a need for FW to know when we enable
the queue that it is multicast queue so it will be bound to
the multicast FIFO. There is no such way in current design.

In order to simplify driver and firmware handling of this queue
create a multicast station.
This solves the unique RA-TID issue in the short term and serves
as preparation for the long term.

In the long term we will also add a flag marking this station for
the FW as the multicast station.
Once we will do that the FW will know this is the multicast queue
immediately when it is added and bind it to the correct FIFO.
It will also enable removing the special treatment of the
queue in the MAC context command.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When a station is asleep, the fw will set it as "asleep".
All queues that are used only by one station will be stopped by
the fw.

In pre-DQA mode this was relevant for aggregation queues. However,
in DQA mode a queue is owned by one station only, so all queues
will be stopped.
As a result, we don't expect to get filtered frames back to
mac80211 and don't have to maintain the entire pending_frames
state logic, the same way as we do in aggregations.

The correct behavior is to align DQA behavior with the aggregation
queue behaviour pre-DQA:
- Don't count pending frames.
- Let mac80211 know we have frames in these queues so that it can
properly handle trigger frames.

When a trigger frame is received, mac80211 tells the driver to send
frames from the queues using release_buffered_frames.
The driver will tell the fw to let frames out even if the station
is asleep. This is done by iwl_mvm_sta_modify_sleep_tx_count.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When receiving a frame, we currently pull in sizeof(*hdr) plus
some extra (crypto/snap), which is too much, most headers aren't
actually sizeof(*hdr) since that takes into account the 4-address
format but doesn't take into account QoS. As a result, a typical
frame will have 4 bytes of the payload in the SKB header already.

Fix this by calculating the correct header length, and now that
we have that, align the end of the SKB header to a multiple of 4
so that the IP header will be aligned properly when pulled in.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Final API has a reserved field - adjust accordingly.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This will allow to print the name of the commands in the
logs when we sent it.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For a000 devices the binding API needs to include relevant
lmac ID - support the new API.
The new API should be used regardless if the device had CDB or
not. If there is no actual CDB support the binding is bound
to first lmac regardless of the band.
There are some functionality changes in binding restrictions
and quota allocations that will be handled in future patches.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Allow working IBSS also when working in DQA mode.
This is done by setting it to treat the queues the
same as a BSS AP treats the queues.

Fixes: 7948b873 ("iwlwifi: mvm: enable dynamic queue allocation mode")
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This is a static analysis fix.  The warning is:

	drivers/net/wireless/intel/iwlwifi/mvm/fw-dbg.c:912 iwl_mvm_fw_dbg_collect()
	warn: integer overflows 'sizeof(*desc) + len'

I guess this code is supposed to take a NUL character, but if we write
zero bytes then it tries to write -1 characters and crashes.

Fixes: c91b865c ("iwlwifi: mvm: support description for user triggered fw dbg collection")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Access should be by rcu_dereference. Issue was found by sparse.

Fixes: 65e25482 ("iwlwifi: mvm: use firmware station PM notification for AP_LINK_PS")
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When a station is asleep, the fw will set it as "asleep".
All queues that are used only by one station will be stopped by
the fw.

In pre-DQA mode this was relevant for aggregation queues. However,
in DQA mode a queue is owned by one station only, so all queues
will be stopped.
As a result, we don't expect to get filtered frames back to
mac80211 and don't have to maintain the entire pending_frames
state logic, the same way as we do in aggregations.

The correct behavior is to align DQA behavior with the aggregation
queue behaviour pre-DQA:
- Don't count pending frames.
- Let mac80211 know we have frames in these queues so that it can
properly handle trigger frames.

When a trigger frame is received, mac80211 tells the driver to send
frames from the queues using release_buffered_frames.
The driver will tell the fw to let frames out even if the station
is asleep. This is done by iwl_mvm_sta_modify_sleep_tx_count.
Reported-and-tested-by: NJens Axboe <axboe@kernel.dk>
Reported-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Divide a mfuart related print so it won't exceed the allowed
MAX_MSG_LEN (110 bytes) per print.

Fixes: 19f63c53 ("iwlwifi: mvm: support v2 of mfuart load notification")
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When removing an IGTK, iwl_mvm_send_sta_igtk() was
called before station ID was retrieved, so the function
was invoked with an invalid station ID. Fix this by first
getting the station ID.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=192411Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The race happens when we send ADD_STA(auth->assoc) -> LQ_CMD
between the commands the FW sometimes loses the medium for AUX, and
sends a ndp to the AP and the flow becomes, ADD_STA -> send ndp -> LQ_CMD
the problem is that there's no rates yet defined for sending the ndp and
FW generates an assert.

The fix: change the order of the commands to LQ_CMD -> ADD_STA
Signed-off-by: NMordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The session protection set for association is only removed when
BSS_CHANGED_BEACON_INFO is set and BSS_CHANGED_ASSOC is not set.

However, mac80211 may set both on association (in case a beacon was
already received). In this case, mac80211 will not set
BSS_CHANGED_BEACON_INFO on the next beacons because it has already
notified the beacon change, so the session protection is never removed
(until the session protection ends).

When a CSA is received within this time, the station will fail to
folllow the channel switch because it cannot schedule the time event.

Fix this by removing the session protection when
BSS_CHANGED_BEACON_INFO and BSS_CHANGED_ASSOC are both set.
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In https://bugzilla.kernel.org/show_bug.cgi?id=177341 Bob
reported a UBSAN WARNING on rs.c in iwldvm.
Fix the same bug in iwlmvm.

This because
	i = index - 1;
	for (mask = (1 << i); i >= 0; i--, mask >>= 1)

is unsafe: i could be negative and hence we can call <<
on a negative value.
This bug doesn't have any real impact since the condition
of the for loop will prevent any usage of mask.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=177341Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we send a deauth to a station we don't know about, we
need to use the PROBE_RESP queue. This can happen when we
send a deauth to a station that is not associated to us.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When NSSN is behind the reorder buffer due to timeout
the reorder timer isn't getting re-armed until NSSN
catches up. Fix it.

Fixes: 0690405f ("iwlwifi: mvm: add reorder timeout per frame")
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In DQA mode, first_agg_queue is initialized to
IWL_MVM_DQA_MIN_DATA_QUEUE. This causes two bugs in the tx response
flow:

1. When TX fails, we set IEEE80211_TX_STAT_AMPDU_NO_BACK regardless
   if we actually have aggregation open on the queue. This causes
   mac80211 to send a BAR frame even though there is no aggregation
   open.
   Fix that by simply checking the AMPDU flag that is set on by
   mac80211 for AMPDU packets.

2. When reclaiming frames in aggregation mode, we reclaim based on
   scheduler ssn and not the SN.
   The reason is that scheduler ssn may be ahead of SN due to a hole
   in the BA window that was filled.
   However, if we have aggregations open on IWL_MVM_DQA_BSS_CLIENT_QUEUE
   the reclaim flow will still go to the code of non-aggregation
   instead of the aggregation code since IWL_MVM_DQA_BSS_CLIENT_QUEUE
   is smaller than IWL_MVM_DQA_MIN_DATA_QUEUE, although it is a valid
   aggregation queue.
   Fix that by always using the aggregation reclaim code by default in
   DQA mode (currently it is implicitly used by default for all queues
   except the reserved BSS queue).

Fixes: cf961e16 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Handling of the number of space time streams was missing for HT rate in
rate printing function. Fix it.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Extend ieee80211_cqm_rssi_notify with a rssi_level parameter so that
this information can be passed to netlink clients in the next patch, if
available.  Most drivers will have this value at hand.  wl1251 receives
events from the firmware that only tell it whether latest measurement
is above or below threshold so we don't pass any value at this time
(parameter is 0).
Signed-off-by: NAndrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Support new version of beacon template command which deprecates
the use of the tx command inside.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Unify code, remove redundant assignments.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When a small frame is copied completely into the skb->head, the code
doesn't take alignment into account, making mac80211 copy it again
later on architectures that need the alignment. Avoid this by taking
the PAD flag from the device into account when copying.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In DQA mode the check whether to decrement the pending frames
counter relies on the tid status and not on the txq id.
This may result in an inconsistent state of the pending frames
counter in case frame is queued on a non aggregation queue but
with this TID, and will be followed by a failure to remove the
station and later on SYSASSERT 0x3421 when trying to remove the
MAC.
Such frames are for example bar and qos NDPs.
Fix it by aligning the condition of incrementing the counter
with the condition of decrementing it - rely on TID state for
DQA mode.
Also, avoid internal error like this affecting station removal
for DQA mode - since we can know for sure it is an internal
error.

Fixes: cf961e16 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

A few of the static queues are enabled along with the bcast
STA. Make sure they are removed along with it, rather than
waiting for the mac ctxt release.

This is needed because we sometimes have a STA being removed
and then added again (either with the same sta_id or a
different one). If we wait for the mac ctxt release we will
try to allocate the queues again (as this is currently done
in the STA allocation and not in the MAC init) although
they weren't freed, and even if the sta_id of the STA has
changed.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Instead of setting the tx_cmd length in the mvm code, which is
complicated by the fact that DQA may want to temporarily store
the SKB on the side, adjust the length in the PCIe code which
also knows about this since it's responsible for duplicating
all those headers that are account for in this code.

As the PCIe code already relies on the tx_cmd->len field, this
doesn't really introduce any new dependencies.

To make this possible we need to move the memcpy() of the TX
command until after it was updated.

This does even simplify the code though, since the PCIe code
already does a lot of manipulations to build A-MSDUs correctly
and changing the length becomes a simple operation to see how
much was added/removed, rather than predicting it.

Fixes: 24afba76 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We don't really need clear the skb's status area nor store the
dev_cmd into it until we really commit to the frame by handing
it to the transport - defer those operations until just before
we do that.

This doesn't entirely fix the bug with frames not getting sent
out after having been deferred due to DQA, because it doesn't
restore the info->driver_data[0] place that was already set to
zero (or another value) by the A-MSDU logic.

Fixes: 24afba76 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The firmware will soon actually look at the AID field, and
when it does that it'll try to ensure that the AID is never
changing. Due to the way the station is added, it may start
with an invalid AID before it's associated, so to ensure a
constant AID (once it becomes non-zero), track the station
state and set the AID only when the station is associated
and when it disassociates.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This fixes a long-standing bug that was introduced when this code
was introduced: cfg80211 passes a pointer, but we treat it as if
it was passing a value. The result is that we pass the pointer to
the firmware, instead of the value. It's not clear how this could
ever have worked, unless the firmware is ignoring this value.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When driver needs to access the contents of a streaming DMA buffer
without unmapping it it should call dma_sync_single_for_cpu().
Once the call has been made, the CPU "owns" the DMA buffer and can
work with it as needed.
Before the device accesses the buffer, however, ownership should be
transferred back to it with dma_sync_single_for_device().
Both calls weren't performed by the driver, resulting with odd paging
errors on some platforms. Fix it.

Fixes: a6c4fb44 ("iwlwifi: mvm: Add FW paging mechanism for the UMAC on PCI")
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Support getting alive from two LMACs and dumping debug
data from both.
Deprecate older alive notifications no one is using.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There's already a variable with the result in scope, use that.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

If iwl_mvm_find_free_queue() doesn't find a free queue, it will
return an inactive one.
However, not all the call paths free this queue before reassigning
it, which is a bug.
Check it in other paths and act accordingly.

Fixes: 9794c64f ("iwlwifi: mvm: support dqa queue inactivation upon timeout")
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>