The following chips need to enable internal settings to let ASPM
and clock request work.

RTL8111E-VL, RTL8111F, RTL8411, RTL8111G
RTL8105, RTL8402, RTL8106
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use WARN rather than printk followed by WARN_ON(1), for conciseness.

A simplified version of the semantic patch that makes this transformation
is as follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression list es;
@@

-printk(
+WARN(1,
  es);
-WARN_ON(1);
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Building atp.o triggers this GCC warning:
    drivers/net/ethernet/realtek/atp.c: In function ‘set_rx_mode’:
    drivers/net/ethernet/realtek/atp.c:871:26: warning: ‘mc_filter[0]’ may be used uninitialized in this function [-Wuninitialized]

GCC is correct. In promiscuous mode 'mc_filter' will be used
uninitialized in set_rx_mode_8012(), which is apparently inlined into
set_rx_mode().

But it turns out set_rx_mode_8012() will never be called, since
net_local.chip_type will always be RTL8002. So we can just remove
set_rx_mode_8012() and do some related cleanups.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CPSW driver remaps two different IO regions, but fails to unmap them
both. This patch fixes the issue by calling iounmap in the appropriate
places.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code mixes up the CPSW_SS and the CPSW_WR register naming. This patch
changes the names to conform to the published Technical Reference Manual
from TI, in order to make working on the code less confusing.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When underlying phy driver restores its state very fast after being brought
down and up so that macb driver function macb_handle_link_change() was never
called with link state "down", driver's internal representation of phy speed
and duplex (bp->speed and bp->duplex) didn't change. So, macb driver sees no
reason to perform actual write to the NCFGR register, although the speed and
duplex settings in that register were reset when interface was brought down
and up. In that case actual phy speed and duplex differ from NCFGR settings.
The patch fixes that by keeping internal driver representation of speed and
duplex in sync with actual content of NCFGR.
Signed-off-by: NVitalii Demianets <vitas@nppfactor.kiev.ua>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ben Hutchings recently came up with a better way to handle the kconfig
dependencies for the PTP hardware clocks. This patch converts one new and
one older driver to the new scheme.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After d58d46b5 (r8169: jumbo fixes.) max frame len is stored in
rtl_chip_infos[].jumbo_max for each chip and SafeMtu should be gone.
Signed-off-by: NKirill Smelkov <kirr@mns.spb.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Function name should include '_ether_addr'.
Return type should be bool.
Parameter name should be 'addr' not 'dest' (also matching kernel-doc).
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This was missed in commit a24006ed
('ptp: Enable clock drivers along with associated net/PHY drivers')
which enabled sfc's clock driver unconditionally.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a driver for the FEC(MX6) that offers time
stamping and a PTP haderware clock. Because FEC\ENET(MX6)
hardware frequency adjustment is complex, we have implemented
this in software by changing the multiplication factor of the
timecounter.
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A new file fec_ptp.c will use fec_enet_private to support 1588 PTP
move such structure to common header file fec.h
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch hooks into the CPTS code and adds support for the HWTSTAMP
ioctl. The patch includes code for the CPSW version found in the dm814x
even though the background device tree support for this board is still
missing.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a way to configure the CPTS input clock scaling factors
via the device tree.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Because time stamping on both external ports of the switch simultaneously
is positively useless from the application's point of view, this patch
provides a DT configuration method to choose the active port.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a driver for the CPTS that offers time
stamping and a PTP hardware clock. Because some of the
CPTS hardware variants (like the am335x) do not support
frequency adjustment, we have implemented this in software
by changing the multiplication factor of the timecounter.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the cpsw driver to operate correctly with both the
dm814x and the am335x versions of the switch hardware.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch lets the CPSW driver remember the version number in order to
support the two different variants already in the wild.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code mixes up the CPSW_SS and the CPSW_WR register naming. This patch
changes the names to conform to the published Technical Reference Manual
from TI, in order to make working on the code less confusing.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding multicast address to ALE table via netdev ops to subscribe, transmit
or receive multicast frames to and from the network
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If no pinctrl available just report a warning as some architecture may not
need to do anything.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: adapt the error path, remove unneeded headers]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the ethernet frame payload word-aligned, possibly making the
memcpy into the skb a bit faster. This will be even more important
after we eliminate the copy altogether.

Also eliminate the redundant RX_OFFSET constant -- it has the same
definition and purpose as NET_IP_ALIGN.
Signed-off-by: NHavard Skinnemoen <havard@skinnemoen.net>
[nicolas.ferre@atmel.com: adapt to newer kernel]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Handle all TX errors, not only underruns. TX error management is
deferred to a dedicated workqueue.
Reinitialize the TX ring after treating all remaining frames, and
restart the controller when everything has been cleaned up properly.
Napi is not stopped during this task as the driver only handles
napi for RX for now.
With this sequence, we do not need a special check during the xmit
method as the packets will be caught by TX disable during workqueue
execution.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add macb_get_regs() ethtool function and its helper function:
macb_get_regs_len().
The version field is deduced from the IP revision which gives the
"MACB or GEM" information. An additional version field is reserved.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of masking head and tail every time we increment them, just let them
wrap through UINT_MAX and mask them when subscripting. Add simple accessor
functions to do the subscripting properly to minimize the chances of messing
this up.

This makes the code slightly smaller, and hopefully faster as well.  Also,
doing the ring buffer management this way will simplify things a lot when
making the ring sizes configurable in the future.

Available number of descriptors in ring buffer function by David Laight.
Signed-off-by: NHavard Skinnemoen <havard@skinnemoen.net>
[nicolas.ferre@atmel.com: split patch in topics, adapt to newer kernel]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some revision of GEM, TSR status register has more information.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function has little meaning so remove it altogether and
let ethtool core fill in the fields automatically.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert some noisy netdev_dbg() statements to netdev_vdbg(). Defining
DEBUG will no longer fill up the logs; VERBOSE_DEBUG still does.
Add one more verbose debug for ISR status.
Signed-off-by: NHavard Skinnemoen <havard@skinnemoen.net>
[nicolas.ferre@atmel.com: split patch in topics, add ISR status]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove a couple of unneeded barriers and document the remaining ones.
Signed-off-by: NHavard Skinnemoen <havard@skinnemoen.net>
[nicolas.ferre@atmel.com: split patch in topics]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add Gigabit Ethernet mode to GEM cadence IP and enable RGMII connection.
Signed-off-by: NPatrice Vilchez <patrice.vilchez@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The BF518 has a PTP time unit that works in a similar way to other MAC
based clocks, like gianfar, ixp46x, and igb. This patch adds support for
using the blackfin as a PHC. Although the blackfin hardware does offer a
few ancillary features, this patch implements only the basic operations.

Compile tested only.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NBob Liu <lliubbo@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch replaces the sys time stamps and timecompare code with simple
raw hardware time stamps in nanosecond resolution. The only tricky bit is
to find a PTP Hardware Clock period slower than the input clock period
and a power of two.

Compile tested only.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NBob Liu <lliubbo@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hardware time stamping code is a compile time option for the blackfin.
When it is not enabled, the driver should fall back to the standard
ethtool reply to the get_ts_info query.

Compile tested only.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NBob Liu <lliubbo@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Where a PTP clock driver is associated with a net or PHY driver, it
should be enabled automatically whenever that driver is enabled.
Therefore:

- Make PTP clock drivers select rather than depending on PTP_1588_CLOCK
- Remove separate boolean options for PTP clock drivers that are built
  as part of net driver modules.  (This also fixes cases where the PTP
  subsystem is wrongly forced to be built-in.)
- Set 'default y' for PTP clock drivers that depend on specific net
  drivers but are built separately
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PTP hardware clock drivers that select PTP_1588_CLOCK must currently
also select PPS.  For those drivers that don't, the user must enable
PPS, then enable PTP_1588_CLOCK, then the driver.  Simplify things for
developers and users by putting this selection in one place.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These are now established subsystems, and we want drivers to be able
to select PPS and PTP_1588_CLOCK without depending on EXPERIMENTAL.
Further, the use of EXPERIMENTAL is now deprecated in general.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>