When the external configuration triggers the switch to a configured
controller, it means the setup needs to be run. Controllers that start
out unconfigured have only run limited set of HCI commands. This is
not enough for complete operation and thus run the setup procedure
before announcing the new controller index.

This introduces HCI_CONFIG flag as companion to HCI_SETUP flag. The
HCI_SETUP flag is only used once for the initial setup procedure. And
during that procedure hdev->setup driver callback is called. With the
new HCI_CONFIG the switch from unconfigured to configured state is
triggering the same setup procedure just without hdev->setup. This
is required since bringing a controller back to unconfigured state
from configured state is possible.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

When calling Device Remove with BDADDR_ANY we should in a similar way
emit Device Removed events as we do when removing a single device. Since
we have to iterate the list and call device_removed() the dedicated
hci_conn_params_clear_enabled() is not really useful anymore. This patch
removes the helper function and does the event emission and list item
removal in a single loop.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

During the setup phase of a controller, the Bluetooth address will be
read and to have that original address available for later use, store
it as setup address.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

When one or more of the missing configuration options change, then send
this even to all the other management interface clients.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The Set External Configuration management command allows for switching
between configured and unconfigured start if HCI_QURIK_EXTERNAL_CONFIG
is set by the transport driver.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

When a controller requires external configuration, then setting this
quirk will allow indicating this.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

When a Bluetooth controller does not have a valid public Bluetooth
address, then allow the driver to indicate this. If the quirk is
set, the Bluetooth core will switch to unconfigured state first
and will allow userspace to configure the address before starting
the full initialization of the controller.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The current existing device quirks are not documented. So instead of
spreading bits and pieces somewhere in the code, add proper comments
on where these quirks can be used and what behavior they change.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The public address configuration option is value 0x02 since the generic
external configuration is value 0x01. So adjust this accordingly and
also add the value 0x01 to the list.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

In some circumstances we need to look up entries in pend_le_conns and in
other in pend_le_reports. This patch converts the existing lookup
function for pend_le_conns to something that can be used for both lists.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Since there are no more users of this function we can simply go ahead
and remove it.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When powering off (hci_dev_do_close) we should clear both the
pend_le_reports and pend_le_conns types of entries. When powering on
respectively we should populate both lists. This patch converts the
hci_pend_le_conns_clear() function into hci_pend_le_actions_clear()
(which can now be static) and converts the restart_le_auto_conns()
function into restart_le_actions().
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Now that there are no-longer any users of the hci_pend_le_conn_del()
function we can simply go ahead and remove it.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

To simplify manipulation and lookup of hci_conn_params entries of the
type HCI_AUTO_CONN_REPORT it makes sense to store them in their own
list. The new action list_head in hci_conn_params is used for this
purpose.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

In preparation to store also HCI_AUTO_CONN_REPORT entries in a list it
makes sense to convert the existing pend_le_conn list head of
hci_conn_params into a more generically named "action". This makes sense
because a parameter entry will never participate in more than one action
list.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Read Controller Configuration Information command allows retrieving
details about possible configurations option. The supported options are
returned and also the missing options (if any).
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Since the connection parameters are always a basis for adding entries to
hdev->pend_le_conns (so far of type bdaddr_list) it's simpler and more
efficient to have the parameters themselves be the entries in the
pend_le_conns list. We do this by adding another list_head to the
hci_conn_params struct.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

To be able to make the right choice of whether to start passive scanning
or to send out a mgmt_device_found event we need to know if there are
any devices in the le_conn_params list with the auto_connect value set
to HCI_AUTO_CONN_REPORT. This patch adds a counter for this kind of
devices.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This command allows to get the list of currently known controller that
are in unconfigured state.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

When a controller in an unconfigured state gets removed, then send
Unconfigured Index Removed events.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

When a controller is in unconfigured state it is currently hidden
from the management interface. This change now announces the new
controller with an Unconfigured Index Added event and allows clients
to easily detect the controller.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

With the new unconfigured controller state it is possible to provide a
fully functional HCI transport, but disable the higher level operations
that would normally happen. This way userspace can try to configure the
controller before releases the unconfigured state.

The internal state is represented by HCI_UNCONFIGURED. This replaces the
HCI_QUIRK_RAW_DEVICE quirk as internal state representation. This is now
a real state and drivers can use the quirk to actually trigger this
state. In the future this will allow a more fine grained switching from
unconfigured state to configured state for controller inititialization.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

There are more places that can take advantage of is_identity_address()
besides hci_core.c. This patch moves the function to hci_core.h and
gives it the appropriate hci_ prefix.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The calling functions of mgmt_new_conn_param have more information about
the parameters, such as whether the kernel is tracking them or not. It
makes therefore sense to have them pass an initial store_hint value to
the mgmt_new_conn_param function.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The caller of hci_le_conn_update is directly interested in knowing what
the best value is for the store_hint parameter of the corresponding
mgmt event. Since hci_le_conn_update knows whether there were stored
parameters that were updated or not we can have it return an initial
store_hint value to the caller.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch implements the new Load Connection Parameters mgmt command
that's intended to load the desired connection parameters for LE
devices.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The 0x00 action value of mgmt means "scan and report" but do not
connect. This is different from HCI_AUTO_CONN_DISABLED so we need a new
value for it.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

In some circumstances we'll need to either clear only the enabled
parameters or only the disabled ones. This patch adds convenience
functions for this purpose.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

We'll soon have specific clear functions for clearing enabled or
disabled entries, so rename the function that removes everything to
clear_all().
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Some embedded controllers allow the programming of a public address
and this adds vendor support for supporting OEM confguration of such
addresses.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This patch introduces a new Mgmt event called "New Connection Parameter".
This event indicates to userspace the connection parameters values the
remote device requested.

The user may store these values and load them into kernel. This way, next
time a connection is established to that device, the kernel will use those
parameters values instead of the default ones.

This event is sent when the remote device requests new connection
parameters through connection parameter update procedure. This event is
not sent for slave connections.
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Bluetooth 4.1 introduces a new LE meta event called "LE Remote
Connection Parameter Request" event. In order to the controller
sends this event to host, we should enable it during controller
initialization.
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds support for LE Connection Parameters Request Link
Layer control procedure introduced in Core spec 4.1. This procedure
allows a Peripheral or Central to update the Link Layer connection
parameters of an established connection.

Regarding the acceptance of connection parameters, the LL procedure
follows the same approach of L2CAP procedure (see l2cap_conn_param_
update_req function). We accept any connection parameters values as
long as they are within the valid range.
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

For the Block/Unblock Device mgmt commands we should only emit the
Blocked/Unblocked events on any socket except for the one which received
the command. The code was previously incorrectly trying to look up a
non-existent pending command and thereby ending up not skipping the
command socket for the event.

We can simplify the code a lot by simply sending the event directly from
the command handler functions. We have the reference to the command
socket available there which makes it easy to pass to the mgmt_event
function for skipping.

The only notable side-effect of this is that the old blacklisting
ioctl's no-longer cause mgmt events to be emitted, however as user space
versions using these ioctl's are not mgmt-aware this is acceptable.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

There are certain subtle differences in behavior when we're encrypted
with the STK, such as allowing re-encryption even though the security
level stays the same. Because of this, add a flag to track whether we're
encrypted with an STK or not.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Device Found events of the management interface should indicate if
it is possible to connect to a remote device or if it is broadcaster
only advertising. To allow this differentation the Not Connectable flag
is introduced that will be set when it is known that a device can not
be connected.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Providing the flags parameter directly to mgmt_device_found function
makes the core simpler and more readable. With this it becomes a lot
easier to add new flags in the future.

This also changes hci_inquiry_cache_update to just return that flags
needed for mgmt_device_found since that is its only use for the two
return parameters anyway.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The connection interval parameter of hci_conn_params_set are always used
with the controller defaults. So just let hci_conn_params_add set the
controller default and not bother resetting them to controller defaults
every time the hci_conn_params_set is called.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

When adding new connection parameters, it is useful to return either
the existing struct or the newly created one.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This patch renames l2cap_check_conn_param() to hci_check_conn_params()
and moves it to hci_core.h so it can reused in others files. This helper
will be reused in the next patch.
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>