This structure will also be used for GART in the near future.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Upcoming patches are going to enable full support for buffers that keep
a constant GPU virtual address whenever they're validated for use by
the GPU.

In order for this to work properly while keeping support for large pages,
we need to know if it's ever going to be possible for a buffer to end
up in GART, and if so, disable large pages for the buffer's VMA.

This is a new restriction that's not present in earlier kernel's, but
should not break userspace as the current code never attempts to validate
buffers into a memtype other than it was created with.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

'mappable' isn't really used at all, nor is it necessary anymore as the
bo code is capable of moving buffers to mappable vram as required.

'no_vm' isn't necessary anymore either, any places that don't want to be
mapped into a GPU address space should allocate the VRAM directly instead.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

We need to be able to have the bh run while possibly spinning waiting for
the EVO notifier to signal.  This apparently happens in some circumstances
with preempt disabled, so our workqueue was never being run.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

With cmwq, there's no reason for nouveau to use a dedicated workqueue.
Drop dev_priv->wq and use system_wq instead.  Each work item is sync
flushed when the containing structure is unregistered/destroyed.

Note that this change also makes sure that nv50_gpio_handler is not
freed while the contained work item is still running.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

v2. moved nv44 pciegart table back to instmem, where it's not
    accessible by userspace clients.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

In preparation for the addition of a new nv40 backend, we'll need to be
able to distinguish between a paged dma object and the on-chip GART.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Somehow missed this in the original merge of the nvc0 code.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

We need to track the state of the switch in drivers, so that after s/r
we don't resume the card we've explicitly switched off before. Also
don't allow a userspace open to occur if we've switched the gpu off.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

NVC0 will be able to share some of nv50's paths this way.  This also makes
it the card-specific vram code responsible for deciding if a given set
of tile_flags is valid, rather than duplicating the allowed types in
nv50_vram.c and nouveau_gem.c
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

As of this commit, it's guaranteed that if an object is in VRAM that its
GPU virtual address will be constant.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

This is required on nv50 as we need to be able to have more precise control
over physical VRAM allocations to avoid buffer corruption when using
buffers of mixed memory types.

This removes some nasty overallocation/alignment that we were previously
using to "control" this problem.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

This will be used later to fixup bo.offset with a buffer's fixed GPU
virtual address.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

There have been reports of PFIFO cache errors during context take down
(fdo bug 31637). They are caused by some GPU objects being taken out
while the channel is still potentially processing commands. Make sure
that all the previous rendering has landed before releasing a GPU
object.
Reported-by: NGrzesiek Sójka <pld@pfu.pl>
Reported-by: NPatrice Mandin <patmandin@gmail.com>
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Acked-by: NBen Skeggs <bskeggs@redhat.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Reviewed-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Reviewed-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Reviewed-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Allows callers to install their own handlers for when a GPIO line
changes state (such as for hotplug detect).

This also fixes a bug where we weren't acknowledging the GPIO IRQ
until after the bottom half had run, causing a severe IRQ storm
in some cases.
Reviewed-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Reviewed-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Reviewed-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Reviewed-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>