Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 12 10月, 2009 4 次提交
  3. 09 10月, 2009 1 次提交
  5. 08 10月, 2009 22 次提交
  7. 07 10月, 2009 10 次提交
    • S
      ipv4: arp_notify address list bug · a21090cf
      由 Stephen Hemminger 提交于 
      This fixes a bug with arp_notify.

If arp_notify is enabled, kernel will crash if address is changed
and no IP address is assigned.
  http://bugzilla.kernel.org/show_bug.cgi?id=14330Reported-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      a21090cf
    • S
      net: mark net_proto_ops as const · ec1b4cf7
      由 Stephen Hemminger 提交于 
      All usages of structure net_proto_ops should be declared const.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ec1b4cf7
    • O
      make TLLAO option for NA packets configurable · f7734fdf
      由 Octavian Purdila 提交于 
      On Friday 02 October 2009 20:53:51 you wrote:

> This is good although I would have shortened the name.

Ah, I knew I forgot something :) Here is v4.

tavi

>From 24d96d825b9fa832b22878cc6c990d5711968734 Mon Sep 17 00:00:00 2001
From: Octavian Purdila <opurdila@ixiacom.com>
Date: Fri, 2 Oct 2009 00:51:15 +0300
Subject: [PATCH] ipv6: new sysctl for sending TLLAO with unicast NAs

Neighbor advertisements responding to unicast neighbor solicitations
did not include the target link-layer address option. This patch adds
a new sysctl option (disabled by default) which controls whether this
option should be sent even with unicast NAs.

The need for this arose because certain routers expect the TLLAO in
some situations even as a response to unicast NS packets.

Moreover, RFC 2461 recommends sending this to avoid a race condition
(section 4.4, Target link-layer address)
Signed-off-by: NCosmin Ratiu <cratiu@ixiacom.com>
Signed-off-by: NOctavian Purdila <opurdila@ixiacom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      f7734fdf
    • B
      Use sk_mark for IPv6 routing lookups · 51953d5b
      由 Brian Haley 提交于 
      Atis Elsts wrote:
> Not sure if there is need to fill the mark from skb in tunnel xmit functions. In any case, it's not done for GRE or IPIP tunnels at the moment.

Ok, I'll just drop that part, I'm not sure what should be done in this case.

> Also, in this patch you are doing that for SIT (v6-in-v4) tunnels only, and not doing it for v4-in-v6 or v6-in-v6 tunnels. Any reason for that?

I just sent that patch out too quickly, here's a better one with the updates.

Add support for IPv6 route lookups using sk_mark.
Signed-off-by: NBrian Haley <brian.haley@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      51953d5b
    • B
      ethtool: Add reset operation · d73d3a8c
      由 Ben Hutchings 提交于 
      After updating firmware stored in flash, users may wish to reset the
relevant hardware and start the new firmware immediately.  This should
not be completely automatic as it may be disruptive.

A selective reset may also be useful for debugging or diagnostics.

This adds a separate reset operation which takes flags indicating the
components to be reset.  Drivers are allowed to reset only a subset of
those requested, and must indicate the actual subset.  This allows the
use of generic component masks and some future expansion.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      d73d3a8c
    • E
      pkt_sched: gen_estimator: Dont report fake rate estimators · d250a5f9
      由 Eric Dumazet 提交于 
      Jarek Poplawski a écrit :
>
>
> Hmm... So you made me to do some "real" work here, and guess what?:
> there is one serious checkpatch warning! ;-) Plus, this new parameter
> should be added to the function description. Otherwise:
> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
>
> Thanks,
> Jarek P.
>
> PS: I guess full "Don't" would show we really mean it...

Okay :) Here is the last round, before the night !

Thanks again

[RFC] pkt_sched: gen_estimator: Don't report fake rate estimators

We currently send TCA_STATS_RATE_EST elements to netlink users, even if no estimator
is running.

# tc -s -d qdisc
qdisc pfifo_fast 0: dev eth0 root bands 3 priomap  1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1
 Sent 112833764978 bytes 1495081739 pkt (dropped 0, overlimits 0 requeues 0)
 rate 0bit 0pps backlog 0b 0p requeues 0

User has no way to tell if the "rate 0bit 0pps" is a real estimation, or a fake
one (because no estimator is active)

After this patch, tc command output is :
$ tc -s -d qdisc
qdisc pfifo_fast 0: dev eth0 root bands 3 priomap  1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1
 Sent 561075 bytes 1196 pkt (dropped 0, overlimits 0 requeues 0)
 backlog 0b 0p requeues 0

We add a parameter to gnet_stats_copy_rate_est() function so that
it can use gen_estimator_active(bstats, r), as suggested by Jarek.

This parameter can be NULL if check is not necessary, (htb for
example has a mandatory rate estimator)
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      d250a5f9
    • E
      Use sk_mark for routing lookup in more places · 2d37a186
      由 Eric Dumazet 提交于 
      Here is a followup on this area, thanks.

[RFC] af_packet: fill skb->mark at xmit

skb->mark may be used by classifiers, so fill it in case user
set a SO_MARK option on socket.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      2d37a186
    • Y
      ipv6 sit: 6rd (IPv6 Rapid Deployment) Support. · fa857afc
      由 YOSHIFUJI Hideaki / 吉藤英明 提交于 
      IPv6 Rapid Deployment (6rd; draft-ietf-softwire-ipv6-6rd) builds upon
mechanisms of 6to4 (RFC3056) to enable a service provider to rapidly
deploy IPv6 unicast service to IPv4 sites to which it provides
customer premise equipment.  Like 6to4, it utilizes stateless IPv6 in
IPv4 encapsulation in order to transit IPv4-only network
infrastructure.  Unlike 6to4, a 6rd service provider uses an IPv6
prefix of its own in place of the fixed 6to4 prefix.

With this option enabled, the SIT driver offers 6rd functionality by
providing additional ioctl API to configure the IPv6 Prefix for in
stead of static 2002::/16 for 6to4.

Original patch was done by Alexandre Cassen <acassen@freebox.fr>
based on old Internet-Draft.
Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      fa857afc
    • I
      add vif using local interface index instead of IP · ee5e81f0
      由 Ilia K 提交于 
      When routing daemon wants to enable forwarding of multicast traffic it
performs something like:

       struct vifctl vc = {
               .vifc_vifi  = 1,
               .vifc_flags = 0,
               .vifc_threshold = 1,
               .vifc_rate_limit = 0,
               .vifc_lcl_addr = ip, /* <--- ip address of physical
interface, e.g. eth0 */
               .vifc_rmt_addr.s_addr = htonl(INADDR_ANY),
         };
       setsockopt(fd, IPPROTO_IP, MRT_ADD_VIF, &vc, sizeof(vc));

This leads (in the kernel) to calling  vif_add() function call which
search the (physical) device using assigned IP address:
       dev = ip_dev_find(net, vifc->vifc_lcl_addr.s_addr);

The current API (struct vifctl) does not allow to specify an
interface other way than using it's IP, and if there are more than a
single interface with specified IP only the first one will be found.

The attached patch (against 2.6.30.4) allows to specify an interface
by its index, instead of IP address:

       struct vifctl vc = {
               .vifc_vifi  = 1,
               .vifc_flags = VIFF_USE_IFINDEX,   /* NEW */
               .vifc_threshold = 1,
               .vifc_rate_limit = 0,
               .vifc_lcl_ifindex = if_nametoindex("eth0"),   /* NEW */
               .vifc_rmt_addr.s_addr = htonl(INADDR_ANY),
         };
       setsockopt(fd, IPPROTO_IP, MRT_ADD_VIF, &vc, sizeof(vc));
Signed-off-by: NIlia K. <mail4ilia@gmail.com>

=== modified file 'include/linux/mroute.h'
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ee5e81f0
    • E
      net: speedup sk_wake_async() · bcdce719
      由 Eric Dumazet 提交于 
      An incoming datagram must bring into cpu cache *lot* of cache lines,
in particular : (other parts omitted (hash chains, ip route cache...))

On 32bit arches :

offsetof(struct sock, sk_rcvbuf)       =0x30    (read)
offsetof(struct sock, sk_lock)         =0x34   (rw)

offsetof(struct sock, sk_sleep)        =0x50 (read)
offsetof(struct sock, sk_rmem_alloc)   =0x64   (rw)
offsetof(struct sock, sk_receive_queue)=0x74   (rw)

offsetof(struct sock, sk_forward_alloc)=0x98   (rw)

offsetof(struct sock, sk_callback_lock)=0xcc    (rw)
offsetof(struct sock, sk_drops)        =0xd8 (read if we add dropcount support, rw if frame dropped)
offsetof(struct sock, sk_filter)       =0xf8    (read)

offsetof(struct sock, sk_socket)       =0x138 (read)

offsetof(struct sock, sk_data_ready)   =0x15c   (read)


We can avoid sk->sk_socket and socket->fasync_list referencing on sockets
with no fasync() structures. (socket->fasync_list ptr is probably already in cache
because it shares a cache line with socket->wait, ie location pointed by sk->sk_sleep)

This avoids one cache line load per incoming packet for common cases (no fasync())

We can leave (or even move in a future patch) sk->sk_socket in a cold location
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      bcdce719
  9. 05 10月, 2009 3 次提交
    • J
      wext: let get_wireless_stats() sleep · a160ee69
      由 Johannes Berg 提交于 
      A number of drivers (recently including cfg80211-based ones)
assume that all wireless handlers, including statistics, can
sleep and they often also implicitly assume that the rtnl is
held around their invocation. This is almost always true now
except when reading from sysfs:

  BUG: sleeping function called from invalid context at kernel/mutex.c:280
  in_atomic(): 1, irqs_disabled(): 0, pid: 10450, name: head
  2 locks held by head/10450:
   #0:  (&buffer->mutex){+.+.+.}, at: [<c10ceb99>] sysfs_read_file+0x24/0xf4
   #1:  (dev_base_lock){++.?..}, at: [<c12844ee>] wireless_show+0x1a/0x4c
  Pid: 10450, comm: head Not tainted 2.6.32-rc3 #1
  Call Trace:
   [<c102301c>] __might_sleep+0xf0/0xf7
   [<c1324355>] mutex_lock_nested+0x1a/0x33
   [<f8cea53b>] wdev_lock+0xd/0xf [cfg80211]
   [<f8cea58f>] cfg80211_wireless_stats+0x45/0x12d [cfg80211]
   [<c13118d6>] get_wireless_stats+0x16/0x1c
   [<c12844fe>] wireless_show+0x2a/0x4c

Fix this by using the rtnl instead of dev_base_lock.
Reported-by: NMiles Lane <miles.lane@gmail.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      a160ee69
    • A
      net: export device speed and duplex via sysfs · d519e17e
      由 Andy Gospodarek 提交于 
      This patch exports the link-speed (in Mbps) and duplex of an interface
via sysfs.  This eliminates the need to use ethtool just to check the
link-speed.  Not requiring 'ethtool' and not relying on the SIOCETHTOOL
ioctl should be helpful in an embedded environment where space is at a
premium as well.

NOTE: This patch also intentionally allows non-root users to check the link
speed and duplex -- something not possible with ethtool.

Here's some sample output:

# cat /sys/class/net/eth0/speed
100
# cat /sys/class/net/eth0/duplex
half
# ethtool eth0
Settings for eth0:
        Supported ports: [ TP ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Supports auto-negotiation: Yes
        Advertised link modes:  Not reported
        Advertised auto-negotiation: No
        Speed: 100Mb/s
        Duplex: Half
        Port: Twisted Pair
        PHYAD: 1
        Transceiver: internal
        Auto-negotiation: off
        Supports Wake-on: g
        Wake-on: g
        Current message level: 0x000000ff (255)
        Link detected: yes
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      d519e17e
    • M
      cfg80211: assign device type in netdev notifier callback · 053a93dd
      由 Marcel Holtmann 提交于 
      Instead of having to modify every non-mac80211 for device type assignment,
do this inside the netdev notifier callback of cfg80211. So all drivers
that integrate with cfg80211 will export a proper device type.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      053a93dd