Resolves the following build warnings:
drivers/usb/host/xhci.c:332:13: warning: 'xhci_msix_sync_irqs' defined but not used [-Wunused-function]
drivers/usb/host/xhci.c:3901:12: warning: 'xhci_change_max_exit_latency' defined but not used [-Wunused-function]

These functions are not always used, and since they're marked static
they will produce build warnings:
- xhci_msix_sync_irqs is only used with CONFIG_PCI.
- xhci_change_max_exit_latency is a little more complicated with
  dependencies on CONFIG_PM and CONFIG_PM_RUNTIME.

Instead of building a bigger maze of ifdefs in this code, I've just
marked both with __maybe_unused.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

When the host controller fails to respond to an Enable Slot command, and
the host fails to respond to the register write to abort the command
ring, the xHCI driver will assume the host is dead, and call
usb_hc_died().

The USB device's slot_id is still set to zero, and the pointer stored at
xhci->devs[0] will always be NULL.  The call to xhci_check_args in
xhci_free_dev should have caught the NULL virt_dev pointer.

However, xhci_free_dev is designed to free the xhci_virt_device
structures, even if the host is dead, so that we don't leak kernel
memory.  xhci_free_dev checks the return value from the generic
xhci_check_args function.  If the return value is -ENODEV, it carries on
trying to free the virtual device.

The issue is that xhci_check_args looks at the host controller state
before it looks at the xhci_virt_device pointer.  It will return -ENIVAL
because the host is dead, and xhci_free_dev will ignore the return
value, and happily dereference the NULL xhci_virt_device pointer.

The fix is to make sure that xhci_check_args checks the xhci_virt_device
pointer before it checks the host state.

See https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1203453 for
further details.  This patch doesn't solve the underlying issue, but
will ensure we don't see any more NULL pointer dereferences because of
the issue.

This patch should be backported to kernels as old as 3.1, that
contain the commit 7bd89b40 "xhci: Don't
submit commands or URBs to halted hosts."
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NVincent Thiele <vincentthiele@gmail.com>
Cc: stable@vger.kernel.org

This patch adds missing unlocks on error paths in the
xhci_free_streams and xhci_configure_endpoint functions.
Signed-off-by: NEmil Goode <emilgoode@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fail gracefully, instead of causing the kernel to panic, if the input
control context doesn't have the right type (XHCI_CTX_TYPE_INPUT).  Push
finding the pointer to the input control context up into functions that
can fail.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: John Youn <johnyoun@synopsys.com>

Adds abitilty to tune L1 timeout (inactivity timer for usb2 link sleep)
and BESL (best effort service latency)via sysfs.

This also adds a new usb2_lpm_parameters structure with those variables to
struct usb_device.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

usb 2.0 devices with link power managment (LPM) can describe their idle link
timeouts either in BESL or HIRD format, so far xHCI has only supported HIRD but
later xHCI errata add BESL support as well

BESL timeouts need to inform exit latency changes with an evaluate
context command the same way USB 3.0 link PM code does.
The same xhci_change_max_exit_latency() function is used as with USB3
but code is pulled out from #ifdef CONFIG_PM as USB2.0 BESL LPM
funcionality does not depend on CONFIG_PM.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Hardware link powermanagement in usb2 is a per-port capability.
Previously support for hw lpm was enabled for all ports if any usb2 port supported it.

Now instead cache the capability values and check them for each port individually
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

According to Felipe and Alan's comments the second parameter of irq
handler should be 'void *' not a specific structure pointer.
So change it.
Signed-off-by: NAlex Shi <alex.shi@intel.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

When CONFIG_XHCI_HCD_DEBUGGING is activated, the XHCI driver can dump
device and input contexts to the console. The endpoint contexts in that
dump are labeled "Endpoint N Context", where N is the XHCI endpoint
index (DCI - 1). This can be very confusing, especially for people who
are not that familiar with the XHCI specification. This patch introduces
an xhci_get_endpoint_address function (as a counterpart to the reverse
xhci_get_endpoint_index), and uses it to additionally display the
endpoint number and direction when dumping contexts, which are much more
commonly used concepts in USB.
Signed-off-by: NJulius Werner <jwerner@chromium.org>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Some xHCI hosts contain a "redriver" from TI that silently drops port
status connect changes if the port slips into Compliance Mode.  If the
port slips into compliance mode while the host is in D0, there will not
be a port status change event.  If the port slips into compliance mode
while the host is in D3, the host will not send a PME.  This includes
when the system is suspended (S3) or hibernated (S4).

If this happens when the system is in S3/S4, there is nothing software
can do.  Other port status change events that would normally cause the
host to wake the system from S3/S4 may also be lost.  This includes
remote wakeup, disconnects and connects on other ports, and overrcurrent
events.  A decision was made to _NOT_ disable system suspend/hibernate
on these systems, since users are unlikely to enable wakeup from S3/S4
for the xHCI host.

Software can deal with this issue when the system is in S0.  A work
around was put in to poll the port status registers for Compliance Mode.
The xHCI driver will continue to poll the registers while the host is
runtime suspended.  Unfortunately, that means we can't allow the PCI
device to go into D3cold, because power will be removed from the host,
and the config space will read as all Fs.

Disable D3cold in the xHCI PCI runtime suspend function.

This patch should be backported to kernels as old as 3.2, that
contain the commit 71c731a2 "usb: host:
xhci: Fix Compliance Mode on SN65LVPE502CP Hardware"
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: stable@vger.kernel.org

Commit 71c731a2 (usb: host: xhci: Fix Compliance Mode on SN65LVPE502CP
Hardware) was a workaround for systems using the SN65LVPE502CP,
controller, but it introduced a bug in resume from hibernate.

The fix created a timer, comp_mode_recovery_timer, which is deleted from
a timer list when xhci_suspend() is called. However, the hibernate image,
including the timer list containing the comp_mode_recovery_timer, had
already been saved before the timer was deleted.

Upon resume from hibernate, the list containing the comp_mode_recovery_timer
is restored from the image saved to disk, and xhci_resume(), assuming that
the timer had been deleted by xhci_suspend(), makes a call to
compliance_mode_recoery_timer_init(), which creates a new instance of the
comp_mode_recovery_timer and attempts to place it into the same list in which
it is already active, thus corrupting the list during the list_add() call.

At this point, a call trace is emitted indicating the list corruption.
Soon afterward, the system locks up, the watchdog times out, and the
ensuing NMI crashes the system.

The problem did not occur when resuming from suspend. In suspend, the
image in RAM remains exactly as it was when xhci_suspend() deleted the
comp_mode_recovery_timer, so there is no problem when xhci_resume()
creates a new instance of this timer and places it in the still empty
list.

This patch avoids the problem by deleting the timer in xhci_resume()
when resuming from hibernate. Now xhci_resume() can safely make the
call to create a new instance of this timer, whether returning from
suspend or hibernate.

Thanks to Alan Stern for his help with understanding the problem.

[Sarah reworked this patch to cover the case where the xHCI restore
register operation fails, and (temp & STS_SRE) is true (and we re-init
the host, including re-init for the compliance mode), but hibernate is
false.  The original patch would have caused list corruption in this
case.]

This patch should be backported to kernels as old as 3.2, that
contain the commit 71c731a2 "usb: host:
xhci: Fix Compliance Mode on SN65LVPE502CP Hardware"
Signed-off-by: NTony Camuso <tcamuso@redhat.com>
Tested-by: NTony Camuso <tcamuso@redhat.com>
Acked-by: NDon Zickus <dzickus@redhat.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

There are no functional changes in this patch. However, because the
compliance mode timer can be deleted in more than one function, it
seemed expedient to include the function name in the debug strings.

Also limited the use of capitals to the first word in the compliance
mode debug messages, except after a function name where all words
start with lower case, in keeping with the style prevalent elsewhere
in xhci.c.
Signed-off-by: NTony Camuso <tcamuso@redhat.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

This patch (as1675) removes the CONFIG_USB_SUSPEND option, essentially
replacing it everywhere with CONFIG_PM_RUNTIME (except for one place
in hub.c, where it is replaced with CONFIG_PM because the code needs
to be used in both runtime and system PM).  The net result is code
shrinkage and simplification.

There's very little point in keeping CONFIG_USB_SUSPEND because almost
everybody enables it.  The few that don't will find that the usbcore
module has gotten somewhat bigger and they will have to take active
measures if they want to prevent hubs from being runtime suspended.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: Peter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci driver divides the root hub into two logical hubs which work
respectively for usb 2.0 and usb 3.0 devices. They are independent
devices in the usb core. But in the ACPI table, it's one device node
and all usb2.0 and usb3.0 ports are under it. Binding usb port with
its acpi node needs the raw port number which is reflected in the xhci
extended capabilities table. This patch is to add find_raw_port_number
callback to struct hc_driver(), fill it with xhci_find_raw_port_number()
which will return raw port number and add a wrap usb_hcd_find_raw_port_number().

Otherwise, refactor xhci_find_real_port_number(). Using
xhci_find_raw_port_number() to get real index in the HW port status
registers instead of scanning through the xHCI roothub port array.
This can help to speed up.

All addresses in xhci->usb2_ports and xhci->usb3_ports array are
kown good ports and don't include following bad ports in the extended
capabilities talbe.
     (1) root port that doesn't have an entry
     (2) root port with unknown speed
     (3) root port that is listed twice and with different speeds.

So xhci_find_raw_port_number() will only return port num of good ones
and never touch bad ports above.
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

xhci has its own interrupt enabling routine, which will try to
use MSI-X/MSI if present. So the usb core shouldn't try to enable
legacy interrupts; on some machines the xhci legacy IRQ setting
is invalid.

v3: Be careful to not break XHCI_BROKEN_MSI workaround (by trenn)

Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Frederik Himpe <fhimpe@vub.ac.be>
Cc: David Haerdeman <david@hardeman.nu>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reviewed-by: NThomas Renninger <trenn@suse.de>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The USB core hub thread (khubd) is designed with external USB hubs in
mind.  It expects that if a port status change bit is set, the hub will
continue to send a notification through the hub status data transfer.
Basically, it expects hub notifications to be level-triggered.

The xHCI host controller is designed to be edge-triggered on the logical
'OR' of all the port status change bits.  When all port status change
bits are clear, and a new change bit is set, the xHC will generate a
Port Status Change Event.  If another change bit is set in the same port
status register before the first bit is cleared, it will not send
another event.

This means that the hub code may lose port status changes because of
race conditions between clearing change bits.  The user sees this as a
"dead port" that doesn't react to device connects.

The fix is to turn on port polling whenever a new change bit is set.
Once the USB core issues a hub status request that shows that no change
bits are set in any USB ports, turn off port polling.

We can't allow the USB core to poll the roothub for port events during
host suspend because if the PCI host is in D3cold, the port registers
will be all f's.  Instead, stop the port polling timer, and
unconditionally restart it when the host resumes.  If there are no port
change bits set after the resume, the first call to hub_status_data will
disable polling.

This patch should be backported to stable kernels with the first xHCI
support, 2.6.31 and newer, that include the commit
0f2a7930 "USB: xhci: Root hub support."
There will be merge conflicts because the check for HC_STATE_SUSPENDED
was moved into xhci_suspend in 3.8.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org

that check will have to be done by all users
of xhci_suspend() so it sounds a lot better to
move the check to xhci_suspend() in order to
avoid code duplication.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

This minor patch creates a more stricter conditional for the Z1 sytems for applying
the Compliance Mode Patch, this to avoid the quirk to be applied to models that
contain a "Z1" in their dmi product string but are different from Z1 systems.

This patch should be backported to stable kernels as old as 3.2, that
contain the commit 71c731a2 "usb: host:
xhci: Fix Compliance Mode on SN65LVPE502CP Hardware"
Signed-off-by: NAlexis R. Cortes <alexis.cortes@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

David reports that at drivers/usb/host/xhci.c:2257:

static bool xhci_is_sync_in_ep(unsigned int ep_type)
{
    return (ep_type == ISOC_IN_EP || ep_type != INT_IN_EP);
}

The static analyser cppcheck says

[linux-3.7-rc2/drivers/usb/host/xhci.c:2257]: (style) Redundant condition: If ep_type == 5, the comparison ep_type != 7 is always true.

Maybe the original programmer intention was something like

static bool xhci_is_sync_in_ep(unsigned int ep_type)
{
    return (ep_type == ISOC_IN_EP || ep_type == INT_IN_EP);
}

Fix this.

This patch should be backported to stable kernels as old as 3.2, that
contain the commit 2b698999 "xhci: USB
3.0 BW checking."
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NDavid Binderman <dcb314@hotmail.com>
Cc: stable@vger.kernel.org

Non-static xHCI driver symbols should start with the "xhci_" prefix, in
order to avoid namespace pollution.  Rename the "handshake" function to
"xhci_handshake".
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NBen Hutchings <ben@decadent.org.uk>

Remove the variable ep_ctx from xhci_add_endpoint(), since it is
assigned but unused.  Caught by Coverity.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Coverity complains that xhci_evaluate_context_result() is missing a
break statement after the COMP_EBADSLT switch case.  It's not a big
deal, since we wanted to return the same error code as the case
statement below it does.  The end result would be one that a Slot
Disabled error completion code would also print the warning message
associated with a Context State error code.  No other bad behavior would
result.

It's not worth backporting to stable kernels, since it only fixes an
issue with too much debugging.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

xhci_service_interval_to_ns() returns long long
to avoid an overflow. However, the type cast happens
too late. The fix is to force ULL from the beginning.

This patch should be backported to kernels as old as 3.5, that contain
the commit e3567d2c "xhci: Add Intel
U1/U2 timeout policy."
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
CC: stable@vger.kernel.org

An le16 is accessed without conversion.

This patch should be backported to kernels as old as 3.5, that contain
the commit e3567d2c "xhci: Add Intel
U1/U2 timeout policy."
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
CC: stable@vger.kernel.org

This minor change adds a new system to which the "Fix Compliance Mode
on SN65LVPE502CP Hardware" patch has to be applied also.

System added:
Vendor: Hewlett-Packard. System Model: Z1
Signed-off-by: NAlexis R. Cortes <alexis.cortes@ti.com>
Acked-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In 71c731a2: usb: host: xhci: Fix Compliance Mode on SN65LVPE502CP Hardware
when extracting DMI strings (vendor or product_name) to mark them as quirk
we may get NULL pointer in case of non-x86 systems which won't define
CONFIG_DMI. Hence susbsequent strstr() calls crash while driver probing.

So, returning 'false' here in case we get a NULL vendor or product_name.

This is tested with ARM (exynos) system.

This patch should be backported to stable kernels as old as 3.6, that
contain the commit 71c731a2 "usb: host:
xhci: Fix Compliance Mode on SN65LVPE502CP Hardware"
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NSebastian Gottschall (DD-WRT) <s.gottschall@dd-wrt.com>
Cc: stable@vger.kernel.org

The Intel XHCI specification says that after clearing the run/stop bit
the controller may take up to 16ms to halt. We've seen a device take
14ms, which with the current timeout of 10ms causes the kernel to
abort the suspend. Increasing the timeout to the recommended value
fixes the problem.

This patch should be backported to kernels as old as 2.6.37, that
contain the commit 5535b1d5 "USB: xHCI:
PCI power management implementation".
Signed-off-by: NMichael Spang <spang@chromium.org>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

drivers/usb/host/xhci.c:1826:14: warning: symbol 'xhci_get_block_size' was not declared. Should it be static?
drivers/usb/host/xhci.c:1844:14: warning: symbol 'xhci_get_largest_overhead' was not declared. Should it be static?
drivers/usb/host/xhci-ring.c:2304:36: warning: context imbalance in 'handle_tx_event' - unexpected unlock
drivers/usb/host/xhci-hub.c:425:6: warning: symbol 'xhci_set_remote_wake_mask' was not declared. Should it be static?
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The patch is used to cancel command when the command isn't
acknowledged and a timeout occurs.

This patch should be backported to kernels as old as 3.0, that contain
the commit 7ed603ec "xhci: Add an
assertion to check for virt_dev=0 bug." That commit papers over a NULL
pointer dereference, and this patch fixes the underlying issue that
caused the NULL pointer dereference.
Signed-off-by: NElric Fu <elricfu1@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NMiroslav Sabljic <miroslav.sabljic@avl.com>
Cc: stable@vger.kernel.org

Software have to abort command ring and cancel command
when a command is failed or hang. Otherwise, the command
ring will hang up and can't handle the others. An example
of a command that may hang is the Address Device Command,
because waiting for a SET_ADDRESS request to be acknowledged
by a USB device is outside of the xHC's ability to control.

To cancel a command, software will initialize a command
descriptor for the cancel command, and add it into a
cancel_cmd_list of xhci.

Sarah: Fixed missing newline on "Have the command ring been stopped?"
debugging statement.

This patch should be backported to kernels as old as 3.0, that contain
the commit 7ed603ec "xhci: Add an
assertion to check for virt_dev=0 bug." That commit papers over a NULL
pointer dereference, and this patch fixes the underlying issue that
caused the NULL pointer dereference.
Signed-off-by: NElric Fu <elricfu1@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NMiroslav Sabljic <miroslav.sabljic@avl.com>
Cc: stable@vger.kernel.org

Adding cmd_ring_state for command ring. It helps to verify
the current command ring state for controlling the command
ring operations.

This patch should be backported to kernels as old as 3.0.  The commit
7ed603ec "xhci: Add an assertion to
check for virt_dev=0 bug." papers over the NULL pointer dereference that
I now believe is related to a timed out Set Address command.  This (and
the four patches that follow it) contain the real fix that also allows
VIA USB 3.0 hubs to consistently re-enumerate during the plug/unplug
stress tests.
Signed-off-by: NElric Fu <elricfu1@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NMiroslav Sabljic <miroslav.sabljic@avl.com>
Cc: stable@vger.kernel.org

This patch is intended to work around a known issue on the
SN65LVPE502CP USB3.0 re-driver that can delay the negotiation
between a device and the host past the usual handshake timeout.

If that happens on the first insertion, the host controller
port will enter in Compliance Mode and NO port status event will
be generated (as per xHCI Spec) making impossible to detect this
event by software. The port will remain in compliance mode until
a warm reset is applied to it.

As a result of this, the port will seem "dead" to the user and no
device connections or disconnections will be detected.

For solving this, the patch creates a timer which polls every 2
seconds the link state of each host controller's port (this
by reading the PORTSC register) and recovers the port by issuing a
Warm reset every time Compliance mode is detected.

If a xHC USB3.0 port has previously entered to U0, the compliance
mode issue will NOT occur only until system resumes from
sleep/hibernate, therefore, the compliance mode timer is stopped
when all xHC USB 3.0 ports have entered U0. The timer is initialized
again after each system resume.

Since the issue is being caused by a piece of hardware, the timer
will be enabled ONLY on those systems that have the SN65LVPE502CP
installed (this patch uses DMI strings for detecting those systems)
therefore making this patch to act as a quirk (XHCI_COMP_MODE_QUIRK
has been added to the xhci stack).

This patch applies for these systems:
Vendor: Hewlett-Packard. System Models: Z420, Z620 and Z820.

This patch should be backported to kernels as old as 3.2, as that was
the first kernel to support warm reset.  The kernels will need to
contain both commit 10d674a8 "USB: When
hot reset for USB3 fails, try warm reset" and commit
8bea2bd3 "usb: Add support for root hub
port status CAS".  The first patch add warm reset support, and the
second patch modifies the USB core to issue a warm reset when the port
is in compliance mode.
Signed-off-by: NAlexis R. Cortes <alexis.cortes@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

The intent was to test whether the flag was set.

This patch should be backported to stable kernels as old as 3.0, since
it fixes a bug in commit e95829f4 "xhci:
Switch PPT ports to EHCI on shutdown.", which was marked for stable.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

The Intel desktop boards DH77EB and DH77DF have a hardware issue that
can be worked around by BIOS.  If the USB ports are switched to xHCI on
shutdown, the xHCI host will send a spurious interrupt, which will wake
the system.  Some BIOS will work around this, but not all.

The bug can be avoided if the USB ports are switched back to EHCI on
shutdown.  The Intel Windows driver switches the ports back to EHCI, so
change the Linux xHCI driver to do the same.

Unfortunately, we can't tell the two effected boards apart from other
working motherboards, because the vendors will change the DMI strings
for the DH77EB and DH77DF boards to their own custom names.  One example
is Compulab's mini-desktop, the Intense-PC.  Instead, key off the
Panther Point xHCI host PCI vendor and device ID, and switch the ports
over for all PPT xHCI hosts.

The only impact this will have on non-effected boards is to add a couple
hundred milliseconds delay on boot when the BIOS has to switch the ports
over from EHCI to xHCI.

This patch should be backported to kernels as old as 3.0, that contain
the commit 69e848c2 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NDenis Turischev <denis@compulab.co.il>
Tested-by: NDenis Turischev <denis@compulab.co.il>
Cc: stable@vger.kernel.org

The NEC/Renesas 720201 xHCI host controller does not complete its reset
within 250 milliseconds.  In fact, it takes about 9 seconds to reset the
host controller, and 1 second for the host to be ready for doorbell
rings.  Extend the reset and CNR polling timeout to 10 seconds each.

This patch should be backported to kernels as old as 2.6.31, that
contain the commit 66d4eadd "USB: xhci:
BIOS handoff and HW initialization."
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NEdwin Klein Mentink <e.kleinmentink@zonnet.nl>
Cc: stable@vger.kernel.org

There are a few (new) usbdevfs capabilities which an application cannot
discover in any other way then checking the kernel version. There are 3
problems with this:
1) It is just not very pretty.
2) Given the tendency of enterprise distros to backport stuff it is not
reliable.
3) As discussed in length on the mailinglist, USBDEVFS_URB_BULK_CONTINUATION
does not work as it should when combined with USBDEVFS_URB_SHORT_NOT_OK
(which is its intended use) on devices attached to an XHCI controller.
So the availability of these features can be host controller dependent,
making depending on them based on the kernel version not a good idea.

This patch besides adding the new ioctl also adds flags for the following
existing capabilities:

USBDEVFS_CAP_ZERO_PACKET,        available since 2.6.31
USBDEVFS_CAP_BULK_CONTINUATION,  available since 2.6.32, except for XHCI
USBDEVFS_CAP_NO_PACKET_SIZE_LIM, available since 3.3

Note that this patch only does not advertise the USBDEVFS_URB_BULK_CONTINUATION
cap for XHCI controllers, bulk transfers with this flag set will still be
accepted when submitted to XHCI controllers.

Returning -EINVAL for them would break existing apps, and in most cases the
troublesome scenario wrt USBDEVFS_URB_SHORT_NOT_OK urbs on XHCI controllers
will never get hit, so this would break working use cases.

The disadvantage of not returning -EINVAL is that cases were it is causing
real trouble may go undetected / the cause of the trouble may be unclear,
but this is the best we can do.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When system software decides to power down the xHC with the intent of
resuming operation at a later time, it will ask xHC to save the internal
state and restore it when resume to correctly recover from a power event.
Two bits are used to enable this operation: Save State and Restore State.

xHCI spec 4.23.2 says software should "Set the Controller Save/Restore
State flag in the USBCMD register and wait for the Save/Restore State
Status flag in the USBSTS register to transition to '0'". However, it does
not define how long software should wait for the SSS/RSS bit to transition
to 0.

Currently the timeout is set to 1ms. There is bug report
(https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1002697)
indicates that the timeout is too short for ASMedia ASM1042 host controller
to save/restore the state successfully. Increase the timeout to 10ms helps to
resolve the issue.

This patch should be backported to stable kernels as old as 2.6.37, that
contain the commit 5535b1d5 "USB: xHCI:
PCI power management implementation"
Signed-off-by: NAndiry Xu <andiry.xu@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: stable@vger.kernel.org

This patch fixes an issue discovered by Dan Carpenter:

The patch 3b3db026: "xhci: Add infrastructure for host-specific
LPM policies." from May 9, 2012, leads to the following warning:
drivers/usb/host/xhci.c:3909 xhci_get_timeout_no_hub_lpm()
         warn: signedness bug returning '-22'

  3906          default:
  3907                  dev_warn(&udev->dev, "%s: Can't get timeout for non-U1 or U2 state.\n",
  3908                                  __func__);
  3909                  return -EINVAL;
                        ^^^^^^^^^^^^^^
This should be a u16 like USB3_LPM_DISABLED or something.

  3910          }
  3911
  3912          if (sel <= max_sel_pel && pel <= max_sel_pel)
  3913                  return USB3_LPM_DEVICE_INITIATED;
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>

Fengguang reports that the xHCI driver isn't linked properly on his
machine:

ERROR: "__udivdi3" [drivers/usb/host/xhci-hcd.ko] undefined!
ERROR: "handle_edge_irq" [drivers/gpio/gpio-pch.ko] undefined!
ERROR: "irq_to_desc" [drivers/gpio/gpio-pch.ko] undefined!

The driver compiles fine on my 64-bit box (gcc version 4.6.1).
Fengguang thinks it's because the xHCI driver was using DIV_ROUND_UP()
instead of DIV_ROUND_UP_ULL() with arguments that were unsigned long
long variables.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NWu Fengguang <wfg@linux.intel.com>