Sets the bpf program represented by fd as an early filter in the rx path
of the netdev. The fd must have been created as BPF_PROG_TYPE_XDP.
Providing a negative value as fd clears the program. Getting the fd back
via rtnl is not possible, therefore reading of this value merely
provides a bool whether the program is valid on the link or not.
Signed-off-by: NBrenden Blanco <bblanco@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add one new netdev op for drivers implementing the BPF_PROG_TYPE_XDP
filter. The single op is used for both setup/query of the xdp program,
modelled after ndo_setup_tc.
Signed-off-by: NBrenden Blanco <bblanco@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new bpf prog type that is intended to run in early stages of the
packet rx path. Only minimal packet metadata will be available, hence a
new context type, struct xdp_md, is exposed to userspace. So far only
expose the packet start and end pointers, and only in read mode.

An XDP program must return one of the well known enum values, all other
return codes are reserved for future use. Unfortunately, this
restriction is hard to enforce at verification time, so take the
approach of warning at runtime when such programs are encountered. Out
of bounds return codes should alias to XDP_ABORTED.
Signed-off-by: NBrenden Blanco <bblanco@plumgrid.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A subsystem may need to store many copies of a bpf program, each
deserving its own reference. Rather than requiring the caller to loop
one by one (with possible mid-loop failure), add a bulk bpf_prog_add
api.
Signed-off-by: NBrenden Blanco <bblanco@plumgrid.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This manages NCSI packages and channels:

 * The available packages and channels are enumerated in the first
   time of calling ncsi_start_dev(). The channels' capabilities are
   probed in the meanwhile. The NCSI network topology won't change
   until the NCSI device is destroyed.
 * There in a queue in every NCSI device. The element in the queue,
   channel, is waiting for configuration (bringup) or suspending
   (teardown). The channel's state (inactive/active) indicates the
   futher action (configuration or suspending) will be applied on the
   channel. Another channel's state (invisible) means the requested
   action is being applied.
 * The hardware arbitration will be enabled if all available packages
   and channels support it. All available channels try to provide
   service when hardware arbitration is enabled. Otherwise, one channel
   is selected as the active one at once.
 * When channel is in active state, meaning it's providing service, a
   timer started to retrieve the channe's link status. If the channel's
   link status fails to be updated in the determined period, the channel
   is going to be reconfigured. It's the error handling implementation
   as defined in NCSI spec.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: NJoel Stanley <joel@jms.id.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The NCSI command packets are sent from MC (Management Controller)
to remote end. They are used for multiple purposes: probe existing
NCSI package/channel, retrieve NCSI channel's capability, configure
NCSI channel etc.

This defines struct to represent NCSI command packets and introduces
function ncsi_xmit_cmd(), which will be used to transmit NCSI command
packet according to the request. The request is represented by struct
ncsi_cmd_arg.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: NJoel Stanley <joel@jms.id.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NCSI spec (DSP0222) defines several objects: package, channel, mode,
filter, version and statistics etc. This introduces the data structs
to represent those objects and implement functions to manage them.
Also, this introduces CONFIG_NET_NCSI for the newly implemented NCSI
stack.

   * The user (e.g. netdev driver) dereference NCSI device by
     "struct ncsi_dev", which is embedded to "struct ncsi_dev_priv".
     The later one is used by NCSI stack internally.
   * Every NCSI device can have multiple packages simultaneously, up
     to 8 packages. It's represented by "struct ncsi_package" and
     identified by 3-bits ID.
   * Every NCSI package can have multiple channels, up to 32. It's
     represented by "struct ncsi_channel" and identified by 5-bits ID.
   * Every NCSI channel has version, statistics, various modes and
     filters. They are represented by "struct ncsi_channel_version",
     "struct ncsi_channel_stats", "struct ncsi_channel_mode" and
     "struct ncsi_channel_filter" separately.
   * Apart from AEN (Asynchronous Event Notification), the NCSI stack
     works in terms of command and response. This introduces "struct
     ncsi_req" to represent a complete NCSI transaction made of NCSI
     request and response.

link: https://www.dmtf.org/sites/default/files/standards/documents/DSP0222_1.1.0.pdfSigned-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: NJoel Stanley <joel@jms.id.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new function for DSA drivers to handle the switchdev
SWITCHDEV_ATTR_ID_BRIDGE_AGEING_TIME attribute.

The ageing time is passed as milliseconds.

Also because we can have multiple logical bridges on top of a physical
switch and ageing time are switch-wide, call the driver function with
the fastest ageing time in use on the chip instead of the requested one.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This flag indicates whether fragmentation of segments is allowed.

Formerly this policy was hardcoded according to IPSKB_FORWARDED (set by
either ip_forward or ipmr_forward).

Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: NShmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Abstract a general interface "of_phy_get_and_connect"
for PHY connect. User will have no bother with getting
"phy-mode" and "phy-handle" any more.
Suggested-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDongpo Li <lidongpo@hisilicon.com>
Reviewed-by: NJiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for hardware offloading of ipmr/ip6mr we need an
interface that allows to check (and later update) the age of entries.
Relying on stats alone can show activity but not actual age of the entry,
furthermore when there're tens of thousands of entries a lot of the
hardware implementations only support "hit" bits which are cleared on
read to denote that the entry was active and shouldn't be aged out,
these can then be naturally translated into age timestamp and will be
compatible with the software forwarding age. Using a lastuse entry doesn't
affect performance because the members in that cache line are written to
along with the age.
Since all new users are encouraged to use ipmr via netlink, this is
exported via the RTA_EXPIRES attribute.
Also do a minor local variable declaration style adjustment - arrange them
longest to shortest.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
CC: Shrijeet Mukherjee <shm@cumulusnetworks.com>
CC: Satish Ashok <sashok@cumulusnetworks.com>
CC: Donald Sharp <sharpd@cumulusnetworks.com>
CC: David S. Miller <davem@davemloft.net>
CC: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
CC: James Morris <jmorris@namei.org>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The recent change to tracepoint napi:napi_poll changed the order of
the parameters that perf scripts sees, the printk was correct.  The
problem was that the new parameters (work and budget) were pushed
in front of dev_name.

The new parameters obviously need to be appended to keep backward
compatible.

Fixes: 1db19db7 ("net: tracepoint napi:napi_poll add work and budget")
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This work addresses a couple of issues bpf_skb_event_output()
helper currently has: i) We need two copies instead of just a
single one for the skb data when it should be part of a sample.
The data can be non-linear and thus needs to be extracted via
bpf_skb_load_bytes() helper first, and then copied once again
into the ring buffer slot. ii) Since bpf_skb_load_bytes()
currently needs to be used first, the helper needs to see a
constant size on the passed stack buffer to make sure BPF
verifier can do sanity checks on it during verification time.
Thus, just passing skb->len (or any other non-constant value)
wouldn't work, but changing bpf_skb_load_bytes() is also not
the proper solution, since the two copies are generally still
needed. iii) bpf_skb_load_bytes() is just for rather small
buffers like headers, since they need to sit on the limited
BPF stack anyway. Instead of working around in bpf_skb_load_bytes(),
this work improves the bpf_skb_event_output() helper to address
all 3 at once.

We can make use of the passed in skb context that we have in
the helper anyway, and use some of the reserved flag bits as
a length argument. The helper will use the new __output_custom()
facility from perf side with bpf_skb_copy() as callback helper
to walk and extract the data. It will pass the data for setup
to bpf_event_output(), which generates and pushes the raw record
with an additional frag part. The linear data used in the first
frag of the record serves as programmatically defined meta data
passed along with the appended sample.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for non-linear data on raw records. It
extends raw records to have one or multiple fragments that will
be written linearly into the ring slot, where each fragment can
optionally have a custom callback handler to walk and extract
complex, possibly non-linear data.

If a callback handler is provided for a fragment, then the new
__output_custom() will be used instead of __output_copy() for
the perf_output_sample() part. perf_prepare_sample() does all
the size calculation only once, so perf_output_sample() doesn't
need to redo the same work anymore, meaning real_size and padding
will be cached in the raw record. The raw record becomes 32 bytes
in size without holes; to not increase it further and to avoid
doing unnecessary recalculations in fast-path, we can reuse
next pointer of the last fragment, idea here is borrowed from
ZERO_OR_NULL_PTR(), which should keep the perf_output_sample()
path for PERF_SAMPLE_RAW minimal.

This facility is needed for BPF's event output helper as a first
user that will, in a follow-up, add an additional perf_raw_frag
to its perf_raw_record in order to be able to more efficiently
dump skb context after a linear head meta data related to it.
skbs can be non-linear and thus need a custom output function to
dump buffers. Currently, the skb data needs to be copied twice;
with the help of __output_custom() this work only needs to be
done once. Future users could be things like XDP/BPF programs
that work on different context though and would thus also have
a different callback function.

The few users of raw records are adapted to initialize their frag
data from the raw record itself, no change in behavior for them.
The code is based upon a PoC diff provided by Peter Zijlstra [1].

  [1] http://thread.gmane.org/gmane.linux.network/421294Suggested-by: NPeter Zijlstra <peterz@infradead.org>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can't detect the FXEN (fiber mode) bootstrap pin, so configure
it via a boolean device tree property "micrel,fiber-mode".
If it is enabled, auto-negotiation is not supported.
The only available modes are 100base-fx (full duplex and half duplex).
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Including devlink.h on ARM and probably other 32-bit architectures results in
a harmless warning:

In file included from ../include/trace/define_trace.h:95:0,
                 from ../include/trace/events/devlink.h:51,
                 from ../net/core/devlink.c:30:
include/trace/events/devlink.h: In function 'trace_raw_output_devlink_hwmsg':
include/trace/events/devlink.h:42:12: error: format '%lu' expects argument of type 'long unsigned int', but argument 10 has type 'size_t {aka unsigned int}' [-Werror=format=]

The correct format string for 'size_t' is %zu, not %lu, this works on all
architectures.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: e5224f0f ("devlink: add hardware messages tracing facility")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Turned on that driver->owner which is struct module is not available when
modules are disabled. Better to depend on a driver name which is
always available.
Reported-by: NRandy Dunlap <rdunlap@infradead.org>
Fixes: e5224f0f ("devlink: add hardware messages tracing facility")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NRandy Dunlap <rdunlap@infradead.org>
Acked-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This helper serves to know if two switchdev port netdevices belong to the
same HW ASIC, e.g to figure out if forwarding offload is possible between them.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit utilize the ability of ConnectX-4 to bulk read flow counters.
Few bulk counter queries could be done instead of issuing thousands of
firmware commands per second to get statistics of all flows set to HW,
such as those programmed when we offload tc filters.

Counters are stored sorted by hardware id, and queried in blocks (id +
number of counters).

Due to hardware requirement, start of block and number of counters in a
block must be four aligned.
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NAmir Vadai <amir@vadai.me>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to use bulk counters, we need to have counters sorted by id.
Signed-off-by: NAmir Vadai <amir@vadai.me>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Identifying address family operations during rx path is not something
expensive but it's ugly to the eye to have it done multiple times,
specially when we already validated it during initial rx processing.

This patch takes advantage of the now shared sctp_input_cb and make the
pointer to the operations readily available.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SCTP will try to access original IP headers on sctp_recvmsg in order to
copy the addresses used. There are also other places that do similar access
to IP or even SCTP headers. But after 90017acc ("sctp: Add GSO
support") they aren't always there because they are only present in the
header skb.

SCTP handles the queueing of incoming data by cloning the incoming skb
and limiting to only the relevant payload. This clone has its cb updated
to something different and it's then queued on socket rx queue. Thus we
need to fix this in two moments.

For rx path, not related to socket queue yet, this patch uses a
partially copied sctp_input_cb to such GSO frags. This restores the
ability to access the headers for this part of the code.

Regarding the socket rx queue, it removes iif member from sctp_event and
also add a chunk pointer on it.

With these changes we're always able to reach the headers again.

The biggest change here is that now the sctp_chunk struct and the
original skb are only freed after the application consumed the buffer.
Note however that the original payload was already like this due to the
skb cloning.

For iif, SCTP's IPv4 code doesn't use it, so no change is necessary.
IPv6 now can fetch it directly from original's IPv6 CB as the original
skb is still accessible.

In the future we probably can simplify sctp_v*_skb_iif() stuff, as
sctp_v4_skb_iif() was called but it's return value not used, and now
it's not even called, but such cleanup is out of scope for this change.

Fixes: 90017acc ("sctp: Add GSO support")
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The next patch needs 8 bytes in there. sctp_ulpevent has a hole due to
bad alignment; msg_flags is using 4 bytes while it actually uses only 2, so
we shrink it, and iif member (4 bytes) which can be easily fetched from
another place once the next patch is there, so we remove it and thus
creating space for 8 bytes.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We process input path in other files too and having access to it is
nice, so move it to a header where it's shared.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If link is disconnected due to Authentication Failure (PIN or Key
Missing status) userspace will be notified about this with proper error
code. Many LE profiles define "PIN or Key Missing" status as indication
of remote lost bond so this allows userspace to take action on this.

@ Device Connected: 88:63:DF:88:0E:83 (1) flags 0x0000
        02 01 1a 05 03 0a 18 0d 18 0b 09 48 65 61 72 74  ...........Heart
        20 52 61 74 65                                    Rate
> HCI Event: Command Status (0x0f) plen 4
      LE Read Remote Used Features (0x08|0x0016) ncmd 1
        Status: Success (0x00)
> ACL Data RX: Handle 3585 flags 0x02 dlen 11
      ATT: Read By Group Type Request (0x10) len 6
        Handle range: 0x0001-0xffff
        Attribute group type: Primary Service (0x2800)
> HCI Event: LE Meta Event (0x3e) plen 12
      LE Read Remote Used Features (0x04)
        Status: Success (0x00)
        Handle: 3585
        Features: 0x01 0x00 0x00 0x00 0x00 0x00 0x00 0x00
          LE Encryption
< HCI Command: LE Start Encryption (0x08|0x0019) plen 28
        Handle: 3585
        Random number: 0x0000000000000000
        Encrypted diversifier: 0x0000
        Long term key: 26201cd479a0921b6f949f0b1fa8dc82
> HCI Event: Command Status (0x0f) plen 4
      LE Start Encryption (0x08|0x0019) ncmd 1
        Status: Success (0x00)
> HCI Event: Encryption Change (0x08) plen 4
        Status: PIN or Key Missing (0x06)
        Handle: 3585
        Encryption: Disabled (0x00)
< HCI Command: Disconnect (0x01|0x0006) plen 3
        Handle: 3585
        Reason: Authentication Failure (0x05)
> HCI Event: Command Status (0x0f) plen 4
      Disconnect (0x01|0x0006) ncmd 1
        Status: Success (0x00)
> HCI Event: Disconnect Complete (0x05) plen 4
        Status: Success (0x00)
        Handle: 3585
        Reason: Connection Terminated By Local Host (0x16)
@ Device Disconnected: 88:63:DF:88:0E:83 (1) reason 4

@ Device Connected: C4:43:8F:A3:4D:83 (0) flags 0x0000
        08 09 4e 65 78 75 73 20 35                       ..Nexus 5
> HCI Event: Command Status (0x0f) plen 4
      Authentication Requested (0x01|0x0011) ncmd 1
        Status: Success (0x00)
> HCI Event: Link Key Request (0x17) plen 6
        Address: C4:43:8F:A3:4D:83 (LG Electronics)
< HCI Command: Link Key Request Reply (0x01|0x000b) plen 22
        Address: C4:43:8F:A3:4D:83 (LG Electronics)
        Link key: 080812e4aa97a863d11826f71f65a933
> HCI Event: Command Complete (0x0e) plen 10
      Link Key Request Reply (0x01|0x000b) ncmd 1
        Status: Success (0x00)
        Address: C4:43:8F:A3:4D:83 (LG Electronics)
> HCI Event: Auth Complete (0x06) plen 3
        Status: PIN or Key Missing (0x06)
        Handle: 75
@ Authentication Failed: C4:43:8F:A3:4D:83 (0) status 0x05
< HCI Command: Disconnect (0x01|0x0006) plen 3
        Handle: 75
        Reason: Remote User Terminated Connection (0x13)
> HCI Event: Command Status (0x0f) plen 4
      Disconnect (0x01|0x0006) ncmd 1
        Status: Success (0x00)
> HCI Event: Disconnect Complete (0x05) plen 4
        Status: Success (0x00)
        Handle: 75
        Reason: Connection Terminated By Local Host (0x16)
@ Device Disconnected: C4:43:8F:A3:4D:83 (0) reason 4
Signed-off-by: NSzymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Define a tracepoint and allow user to trace messages going to and from
hardware associated with devlink instance.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

prsctp PRIO policy is a policy to abandon lower priority chunks when
asoc doesn't have enough snd buffer, so that the current chunk with
higher priority can be queued successfully.

Similar to TTL/RTX policy, we will set the priority of the chunk to
prsctp_param with sinfo->sinfo_timetolive in sctp_set_prsctp_policy().
So if PRIO policy is enabled, msg->expire_at won't work.

asoc->sent_cnt_removable will record how many chunks can be checked to
remove. If priority policy is enabled, when the chunk is queued into
the out_queue, we will increase sent_cnt_removable. When the chunk is
moved to abandon_queue or dequeue and free, we will decrease
sent_cnt_removable.

In sctp_sendmsg, we will check if there is enough snd buffer for current
msg and if sent_cnt_removable is not 0. Then try to abandon chunks in
sctp_prune_prsctp when sendmsg from the retransmit/transmited queue, and
free chunks from out_queue in right order until the abandon+free size >
msg_len - sctp_wfree. For the abandon size, we have to wait until it
sends FORWARD TSN, receives the sack and the chunks are really freed.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

prsctp TTL policy is a policy to abandon chunks when they expire
at the specific time in local stack. It's similar with expires_at
in struct sctp_datamsg.

This patch uses sinfo->sinfo_timetolive to set the specific time for
TTL policy. sinfo->sinfo_timetolive is also used for msg->expires_at.
So if prsctp_enable or TTL policy is not enabled, msg->expires_at
still works as before.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds SCTP_PR_ASSOC_STATUS to sctp sockopt, which is used
to dump the prsctp statistics info from the asoc. The prsctp statistics
includes abandoned_sent/unsent from the asoc. abandoned_sent is the
count of the packets we drop packets from retransmit/transmited queue,
and abandoned_unsent is the count of the packets we drop from out_queue
according to the policy.

Note: another option for prsctp statistics dump described in rfc is
SCTP_PR_STREAM_STATUS, which is used to dump the prsctp statistics
info from each stream. But by now, linux doesn't yet have per stream
statistics info, it needs rfc6525 to be implemented. As the prsctp
statistics for each stream has to be based on per stream statistics,
we will delay it until rfc6525 is done in linux.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds SCTP_DEFAULT_PRINFO to sctp sockopt. It is used
to set/get sctp Partially Reliable Policies' default params,
which includes 3 policies (ttl, rtx, prio) and their values.

Still, if we set policy params in sndinfo, we will use the params
of sndinfo against chunks, instead of the default params.

In this patch, we will use 5-8bit of sp/asoc->default_flags
to store prsctp policies, and reuse asoc->default_timetolive
to store their values. It means if we enable and set prsctp
policy, prior ttl timeout in sctp will not work any more.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to section 4.5 of rfc7496, prsctp_enable should be per asoc.
We will add prsctp_enable to both asoc and ep, and replace the places
where it used net.sctp->prsctp_enable with asoc->prsctp_enable.

ep->prsctp_enable will be initialized with net.sctp->prsctp_enable, and
asoc->prsctp_enable will be initialized with ep->prsctp_enable. We can
also modify it's value through sockopt SCTP_PR_SUPPORTED.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An important information for the napi_poll tracepoint is knowing
the work done (packets processed) by the napi_poll() call. Add
both the work done and budget, as they are related.

Handle trace_napi_poll() param change in dropwatch/drop_monitor
and in python perf script netdev-times.py in backward compat way,
as python fortunately supports optional parameter handling.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As was suggested this patch adds support for the different versions of MLD
and IGMP query types. Since the user visible structure is still in net-next
we can augment it instead of adding netlink attributes.
The distinction between the different IGMP/MLD query types is done as
suggested in Section 7.1, RFC 3376 [1] and Section 8.1, RFC 3810 [2] based
on query payload size and code for IGMP. Since all IGMP packets go through
multicast_rcv() and it uses ip_mc_check_igmp/ipv6_mc_check_mld we can be
sure that at least the ip/ipv6 header can be directly used.

[1] https://tools.ietf.org/html/rfc3376#section-7
[2] https://tools.ietf.org/html/rfc3810#section-8.1Suggested-by: NLinus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The HCI_BREDR naming is confusing since it actually stands for Primary
Bluetooth Controller. Which is a term that has been used in the latest
standard. However from a legacy point of view there only really have
been Basic Rate (BR) and Enhanced Data Rate (EDR). Recent versions of
Bluetooth introduced Low Energy (LE) and made this terminology a little
bit confused since Dual Mode Controllers include BR/EDR and LE. To
simplify this the name HCI_PRIMARY stands for the Primary Controller
which can be a single mode or dual mode controller.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

over time there were multiple requests to access different data
structures and fields of task_struct current, so finally add
the helper to access 'current' as-is. Tracing bpf programs will do
the rest of walking the pointers via bpf_probe_read().
Note that current can be null and bpf program has to deal it with,
but even dumb passing null into bpf_probe_read() is still safe.
Suggested-by: NBrendan Gregg <brendan.d.gregg@gmail.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The routing table of every switch in a tree is currently initialized to
all zeros. This is an issue since 0 is a valid port number.

Add a DSA_RTABLE_NONE=-1 constant to initialize the signed values of the
routing table pointing to other switches.

This fixes the device mapping of the mv88e6xxx driver where the port
pointing to the switch itself and to non-existent switches was wrongly
configured to be 0. It is now set to the expected 0xf value.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch cleanups the WARN_ON which occurs when the sk buffer has
insufficient buffer space by moving the WARN_ON into if condition.
Signed-off-by: NAlexander Aring <aar@pengutronix.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch fixes ieee802154_get_fc_from_skb function on big endian
machines. The function get_unaligned_le16 converts the byte order to
host byte order but we want to keep the byte order like in mac header.
Signed-off-by: NAlexander Aring <aar@pengutronix.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The RIOT-OS stack does send intra-pan frames but don't set the intra pan
flag inside the mac header. It seems this is valid frame addressing but
inefficient. Anyway this patch adds a new function for intra pan
addressing, doesn't matter if intra pan flag or source and destination
are the same. The newly introduction function will be used to check on
intra pan addressing for 6lowpan.
Signed-off-by: NAlexander Aring <aar@pengutronix.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds ieee802154_skb_src_pan function to get the pointer
address of the source pan id at skb mac pointer.
Signed-off-by: NAlexander Aring <aar@pengutronix.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>