Dispc driver presumes that the callers handle locking for all normal
functions. However, omapdrm doesn't handle this, and presumes that all
overlay manager registers are private to that overlay manager, and thus
presumes that configurations for overlay managers can be written via
different threads freely.

For many registers the above is true. The exceptions are DISPC_CONTROL
and DISPC_CONFIG registers, which contain bits for both LCD and TV
overlay managers.

Fixing this properly in omapdrm means a big omapdrm rewrite. So, for
now, add locking to dispc for the problematic registers.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: NSomnath Mukherjee <somnath@ti.com>

omapdrm doesn't always configure the overlays correctly, causing the
overlay setup functions to be called with zero timings. This leads to
division by zero error.

This happens, for example, when a HDMI cable is not connected, but a
user tries to setup a plane with scaling.

Fixing omapdrm is a big job, so for now let's check for the bad timings
in DISPC and return an error.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

When configuring the lcd timings, instead of writing enum values
directly to the HW, use switch-case to get the value to be programmed.

This is safer and also allows us to change the enum values.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DISPC can drive data lines either on rising or falling pixel clock edge,
which can be configured by the user.

Sync lines can also be driven on rising or falling pixel clock edge, but
additionally the HW can be configured to drive the sync lines on
opposite clock edge from the data lines.

This opposite edge setting does not make any sense, as the same effect
can be achieved by just setting the sync lines to be driven on the other
edge compared to the data lines. It feels like some kind of backward
compatibility option, even if all DSS versions seem to have the same
implementation.

To simplify the code and configuration of the signals, and to make the
dispc timings more compatible with what is used on other platforms,
let's just remove the whole opposite-edge support.

The drivers that used OMAPDSS_DRIVE_SIG_OPPOSITE_EDGES setting are
changed so that they use the opposite setting from the data edge.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The DISPC driver checks that the buffer address is not 0. However, when
using TILER, the address space is TILER specific and 0 is a valid
address.

Fix the check to allow address of 0 for TILER.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Nsrinivas pulukuru <srinivas.pulukuru@ti.com>

On DRA7xx, DISPC needs to write output signal polarities not only to a
DISPC register, like for all earlier DSS versions, but to control
module's CTRL_CORE_SMA_SW_1 register.

This patch adds support to write the polarities to control module.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add DRA7xx support to DISPC driver. The DISPC block is the same as on
OMAP5, except the PLL's used for clocking are "videoX", not "dsiX".
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that we have the common DSS PLL support, change DSI to use it. This
results in quite a lot of changes, but almost all of them are trivial
name changes.

The functions to calculate and program the PLL settings can be removed
from dsi.c, as the common PLL API contains the same functionality.

We also need to create struct dss_pll_hw entries for PLL hardware
features for different OMAP platforms, instead of using the
dss_features.c as the old code does.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Preload register is dumped twice for video overlays and mflag register
is not dumped for GFX.

Fix the register dump.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

omapdss drivers cannot handle devices being unbound while the devices
are part of a connected display pipeline. Module refcounts are used to
prevent unloading the modules, but one can still manually unbind the
devices via sysfs, causing crash.

Set suppress_bind_attrs to disable the bind/unbind support via sysfs.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

dispc_mgr_timings_ok() is a bit confusing how it handles the return
value.

Change the function to just return immediately when a timing is deemed
not valid, making the code much easier to follow.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

OMAP2/3 does not support interlace for LCD out. OMAP4+ does, but is not
supported by the driver at the moment.

The driver still accepts interlaced mode for LCD out, causing broken
display output.

This patch makes dispc reject interlace for LCD out.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DISPC reg dump prints a few registers twice. Remove the extra prints.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

When omapdss writes to DISPC_POL_FREQ register, it always ORs the bits
with the current contents of the register, never clearing the old ones,
causing wrong signal polarity settings.

As we write all the bits in DISPC_POL_FREQ, we don't need to care about
the current contents of the register. So fix the issue by constructing
new register value from scratch.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add omap5 entries to dispc's and dss's of_device_id tables.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add DSS features for AM43xx.
Signed-off-by: NSathya Prakash M R <sathyap@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

If LPAE is enabled, dma_addr_t is 64 bit, so we have to
change a few type for everything in this driver to match
again.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The drivers/video directory is a mess. It contains generic video related
files, directories for backlight, console, linux logo, lots of fbdev
device drivers, fbdev framework files.

Make some order into the chaos by creating drivers/video/fbdev
directory, and move all fbdev related files there.

No functionality is changed, although I guess it is possible that some
subtle Makefile build order related issue could be created by this
patch.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NRob Clark <robdclark@gmail.com>
Acked-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Avoid colision with regmap's struct reg_field definition by renaming
omapdss's struct reg_field to dispc_reg_field, and moving it inside
dispc.c as that's the only place it is used.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DSS uses shared irq handlers for DISPC and DSI, because on OMAP3, the
DISPC and DSI share the same irq line.

However, the irq handlers presume that the hardware is enabled, which,
in theory, may not be the case with shared irq handlers. So if an
interrupt happens while the DISPC/DSI is off, the kernel will halt as
the irq handler tries to access the DISPC/DSI registers.

In practice that should never happen, as both DSI and DISPC are in the
same power domain. So if there's an IRQ for one of them, the other is
also enabled. However, if CONFIG_DEBUG_SHIRQ is enabled, the kernel will
generate a spurious IRQ, which then causes the problem.

This patch adds an is_enabled field for both DISPC and DSI, which is
used to track if the HW is enabled. For DISPC the code is slightly more
complex, as the users of DISPC can register the interrupt handler, and
we want to hide the is_enabled handling from the users of DISPC.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add DT support to DISPC. Only thing needed here is the of_match_table.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

omapdss has its own video-timings struct, but we want to move the common
videomode.

The first step is to change the omapdss's pixelclock unit from kHz to
Hz. Also, omapdss uses "pixel_clock" field name, whereas the common
videomode uses "pixelclock" field name. This patch changes the field
name also, as that makes it easy to spot any non-converted pixel_clock
uses.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Instead of relying on the OMAP specific
omap_pm_get_dev_context_loss_count() to detect register context loss, we
can achieve the same in a much simpler way by just observing the DISPC
registers.

We always set DISPC's load mode to LOAD_FRAME_ONLY, which is not the
reset value. Thus we can just observe the load mode to see if we have
lost register context.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

The driver uses DIV_ROUND_UP when calculating decimated width & height.
For example, when decimating with 3, the width is calculated as:

  width = DIV_ROUND_UP(width, decim_x);

This yields bad results for some values. For example, 800/3=266.666...,
which is rounded to 267. When the input width is set to 267, and pixel
increment is set to 3, this causes the dispc to read a line of 801
pixels, i.e. it reads a wrong pixel at the end of the line.

Even more pressing, the above rounding causes a BUG() in pixinc(), as
the value of 801 is used to calculate row increment, leading to a bad
value being passed to pixinc().

This patch fixes the decimation by removing the DIV_ROUND_UP()s when
calculating width and height for decimation.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

commit 7faa9233 OMAPDSS: DISPC: Handle
synclost errors in OMAP3 introduces limits check to prevent SYNCLOST errors
on OMAP3. However, it misses the logic found in Nokia kernels that is
needed to correctly calculate whether 3 tap or 5 tap rescaler to be used as
well as the logic to fallback to 3 taps if 5 taps clock results in too
tight horizontal timings. Without that patch "horizontal timing too tight"
errors are seen when a video with resolution above 640x350 is tried to be
played. The patch is a forward-ported logic found in Nokia N900 and N9/50
kernels.
Signed-off-by: NIvaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DISPC pipeline DMAs preload some bytes of pixel data in the vertical blanking
region before the start of each frame. The preload ensures the pipeline doesn't
underflow when the active region of the display starts.

DISPC_GFX/VIDp_PRELOAD registers allow us to program how many bytes of data
should be preloaded for each pipeline. Calculating a precise preload value
would be a complex function of the pixel clock of the connected display, the
vertical blanking duration and the interconnect traffic at that instance. If
the register is left untouched, a default value is preloaded.

We observe underflows for OMAP4+ SoCs for certain bandwidth intensive use cases
with many other initiators active, and in situations where memory access isn't
very efficient(like accessing Tiler mapped buffers and EMIF configured in
non-interleaved more). The cause of the underflow is because the default preload
value isn't sufficient for the DMA to reach a steady state. We configure the
PRELOAD register such that the pipelines preload data up to the high threshold
of the FIFO.

Preloading lot of data for older SoCs can have a negative impact. Due to slower
interconnects, it's possible that the DISPC DMA cannot preload up to the high
threshold within the vertical blanking region of the panel. We leave the PRELOAD
registers to their reset values since we haven't faced underflows with these
SoCs because of low value of PRELOAD.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DISPC_MSTANDBY_CTRL register is used in the driver, but it's not
restored in dispc_restore_context(), causing problems after resume.

Instead of adding DISPC_MSTANDBY_CTRL to dispc_restore_context(), let's
call _omap_dispc_initial_config() as the first thing in
dispc_runtime_resume(). This will initialize the DISPC core registers
properly, and will avoid similar issues in the future.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

omapdrm (un)registers irqs inside an irq handler. The problem is that
the (un)register function uses dispc_runtime_get/put() to enable the
clocks, and those functions are not irq safe by default.

This was kind of fixed in 48664b21
(OMAPDSS: DISPC: set irq_safe for runtime PM), which makes dispc's
runtime calls irq-safe.

However, using pm_runtime_irq_safe in dispc makes the parent of dispc,
dss, always enabled, effectively preventing PM for the whole DSS module.

This patch makes omapdrm behave better by adding new irq (un)register
functions that do not use dispc_runtime_get/put, and using those
functions in interrupt context. Thus we can make dispc again
non-irq-safe, allowing proper PM.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Rob Clark <robdclark@gmail.com>

OMAP5 has MFLAG feature in DISPC. Add the register definition and dump
it. The register is not used yet, though.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Functions dispc_ovl_set_fifo_threshold and
dispc_ovl_compute_fifo_thresholds need to be exported. Add the
EXPORT_SYMBOLs.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

These aren't necessary after switch, for, and if blocks.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Convert 0 to false and 1 to true when assigning values to bool
variables. Inspired by commit 3db1cd5c.

The simplified semantic patch that find this problem is as
follows (http://coccinelle.lip6.fr/):

@@
bool b;
@@
(
-b = 0
+b = false
|
-b = 1
+b = true
)
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We have a bug with omapdrm, where omapdrm calls dispc's pm_runtime
function in atomic context, and dispc's pm_runtime is not marked as
irq_safe:

BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:952

Dispc's runtime PM callbacks are irq safe, so we can just set the
irq_safe flag to fix the issue.

However, in the long term, I'd rather have omapdrm manage the runtime PM
calls in a better way. Calling get/put for every small operation that
touches the dispc registers is very inefficient. It'd be better and
cleaner to have clear "in-use" and "not-in-use" states for dispc, so
that we don't need to do register context restore for small operations,
only to turn dispc off right afterwards.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DISPC needs to know the clock rate for DIGIT (i.e. TV) channel, and this
clock is provided by either VENC or HDMI modules. Currently DISPC will
call a function in VENC/HDMI, asking what the clock rate is. This means
we have a fixed dependency from DISPC to both VENC and HDMI.

To have a more generic approach, and in particular to allow adding OMAP5
HDMI driver, we need to remove this dependency. This patch makes
VENC/HDMI inform DISPC when the their clock changes, thus reversing the
dependency and removing the issue.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Currently omapdrm creates crtcs, which map directly to DSS overlay
managers, only on demand at init time. This would make it difficult to
manage connecting the display entities in the future, as the code cannot
just search for a suitable overlay manager.

We cannot fix this the sane way, which would be to create crtcs for each
overlay manager, because we need an overlay for each crtc. With limited
number of overlays, that's not possible.

So the solution for now is to detach the overlay manager from the crtc.
crtcs are still created on demand at init time, but all overlay managers
are always initialized by the omapdss.

This way we can create and connect whole display pipelines from the
overlay manager to the display, regardless of which crtcs omapdrm would
create.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DISPC on OMAP5 has a more optimised mechanism of asserting Mstandby to achieve
more power savings when DISPC is configured in Smart Standby mode. This
mechanism leads to underflows when multiple DISPC pipes are enabled.

There is a register field which can let us revert to the older mechanism of
asserting Mstandby. Configure this field to prevent underflows.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

When using a DISPC video pipeline to a fetch a NV12 buffer in a 2D container, we
need to set set a doublestride bit in the video pipe's ATTRIBUTES register. This
is needed because the stride for the UV plane(using a 16 bit Tiler container) is
double the stride for the Y plane(using a 8 bit Tiler container) for the 0 or
180 degree views. The ROW_INC register is meant for the Y plane, and the HW will
calculate the row increment needed for the UV plane by using double the stride
value based on whether this bit is set or not.

Set the bit when we are using a 2D Tiler buffer and when rotation is 0 or 180
degrees. The stride value is the same for 90 and 270 degree Tiler views, hence
the bit shouldn't be set.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Each version of OMAP has a limitation on the maximum pixel clock frequency
supported by an overlay manager. This limit isn't checked by omapdss. Add
dispc feats for lcd and tv managers and check whether the target timings can
be supported or not.

The pixel clock limitations are actually more complex. They depend on which OPP
OMAP is in, and they also depend on which encoder is the manager connected to.
The OPP dependence is ignored as DSS forces the PM framework to be on OPP100
when DSS is enabled, and the encoder dependencies are ignored by DISPC for now.
These limits should come from the encoder driver.

The OMAP2 TRM doesn't mention the maximum pixel clock limit. This value is left
as half of DSS_FCLK, as OMAP2 requires the PCD to be atleast 2.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that the old clock calculation code is no longer used, we can remove
it from the driver.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>