There is a defect in imx6 LPM design.  When SW tries to enter low power
mode with following sequence, the chip will enter low power mode before
A9 CPU execute WFI instruction:

1. Set CCM_CLPCR[1:0] to 2'b00;
2. ARM CPU enters WFI;
3. ARM CPU wakeup from an interrupt event, which is masked by GPC or not
   visible to GPC, such as interrupt from local timer;
4. Set CCM_CLPCR[1:0] to 2'b01 or 2'b10;
5. ARM CPU execute WFI.

Before the last step, the chip will enter WAIT mode if CCM_CLPCR[1:0] is
set to 2'b01, or enter STOP mode if CCM_CLPCR[1:0] is set to 2'b10.

The patch implements a recommended workaround for this issue.

1. SW triggers irq #32(IOMUX) to be always pending manually by setting
   IOMUX_GPR1_GINT bit;
2. SW should then unmask it in GPC before setting CCM LPM;
3. SW should mask it right after CCM LPM is set (bit0-1 of CCM_CLPCR).
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The LPM (Low Power Mode) code that currently sits in imx6q clock driver
will be reused by imx6sl.  Let's move it into pm-imx6q.c, so that we
can keep clock driver SoC specific and reuse pm-imx6q.c on imx6sl.

In order to avoid adding another ioremap for CCM block,
imx6q_pm_set_ccm_base() is created to let clock driver set up ccm_base
for pm code.

During the move, the unused CCGR macros get removed.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Since commit 70dc8a48 (checkpatch: warn when using extern with function
prototypes in .h files), we will get checkpatch warning when updating
common.h following the existing convention which has extern for function
prototypes.

Let's change the convention to not use extern with function prototypes
in this header.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The imx6q_restart() works fine with normal reboot but will run into
problem with emergency reboot like sysrq-b.  In that case, of_iomap()
gets called from interrupt context and hence triggers the BUG_ON in
__get_vm_area_node().

Actually, since commit c1e31d12 (ARM: imx: create
mxc_arch_reset_init_dt() for DT boot), imx6q/dl should try to use
mxc_restart() by calling mxc_arch_reset_init_dt() beforehand, where
things like of_iomap() can be done.

The patch updates mxc_restart() a little bit to get it work for imx6q/dl
and kill imx6q_restart() completely.
Reported-by: NNathan Lynch <nathan_lynch@mentor.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The mx53_display_revision() declaration in common.h is stale and used
nowhere, so remove it.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The patch enables soc bus infrastructure and adds a function
imx_soc_device_init() to report soc info via soc device interface for
imx6qdl and imx6sl.  With the support, user space can get soc related
info by looking at sysfs like below.

  $ cat /sys/devices/soc0/machine
  Freescale i.MX6 Quad SABRE Smart Device Board
  $ cat /sys/devices/soc0/family
  Freescale i.MX
  $ cat /sys/devices/soc0/soc_id
  i.MX6Q
  $ cat /sys/devices/soc0/revision
  1.2
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The patch creates a common function imx_init_revision_from_anatop() by
merging imx6q_init_revision() and imx_anatop_get_digprog(), so that any
SoC that encodes revision info in anatop can use it to initialize
revision.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

It calls imx_set_soc_revision() to set up soc revision in
imx6q_init_revision(), and replaces all the occurrences of
imx6q_revision() with common helper imx_get_soc_revision().
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Similar to what we do for cpu type, the patch adds helper functions
imx_set_soc_revision() and imx_get_soc_revision() to maintain
imx_soc_revision in cpu.c.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

With arch/arm calling of_clk_init(NULL) from time_init(), we can now
remove custom .init_time hooks.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>

Move anatop related (For USB) from board file to anatop driver
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Current imx53_pm_init() implementation is incomplete as it lacks calling
suspend_set_ops().

Use a single imx5_pm_init() function to handle both mx51 and mx53.

This allows mx53 to enter in low-power mode.

Tested on a mx53qsb:

root@freescale /$ echo mem > /sys/power/state
PM: Syncing filesystems ... done.
mmc0: card e624 removed
Freezing user space processes ... (elapsed 0.001 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
Suspending console(s) (use no_console_suspend to debug)

... (Press Power button)

PM: suspend of devices complete after 17.067 msecs
PM: suspend devices took 0.020 seconds
PM: late suspend of devices complete after 0.954 msecs
PM: noirq suspend of devices complete after 1.288 msecs
Disabling non-boot CPUs ...
PM: noirq resume of devices complete after 0.680 msecs
PM: early resume of devices complete after 0.914 msecs
PM: resume of devices complete after 44.955 msecs
PM: resume devices took 0.050 seconds
Restarting tasks ... done.
mmc0: host does not support reading read-only switch. assuming write-enable.
mmc0: new SDHC card at address e624
mmcblk0: mmc0:e624 SU04G 3.69 GiB
 mmcblk0: p1 p2 p3
libphy: 63fec000.etherne:00 - Link is Down
libphy: 63fec000.etherne:00 - Link is Up - 100/Full
root@freescale /$
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Move imx6q L2 initialization function imx6q_init_l2cache() into
system.c, and rename it imx_init_l2cache(), so that other platforms
other than imx6q can also use the function.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NDirk Behme <dirk.behme@de.bosch.com>

Preparing to move the parsing of reboot= to generic kernel code forces
the change in reboot_mode handling to use the enum.

[akpm@linux-foundation.org: fix arch/arm/mach-socfpga/socfpga.c]
Signed-off-by: NRobin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Instead of explicitly calling clock initialization functions, we can
declare the functions with CLK_OF_DECLARE() and then call common
of_clk_init() to have them invoked properly.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add initial support for i.MX6 SoloLite.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The mxc_arch_reset_init() uses static mapping and calls clk_get_sys() to
get clock.  It's suitable for non-DT boot but not for DT boot where
dynamic mapping and of_clk_get() should be used instead.  Create
mxc_arch_reset_init_dt() as the DT variant of mxc_arch_reset_init(),
and change DT platforms to use it.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Commit bca7a5a0 (ARM: cpu hotplug: remove majority of cache flushing
from platforms) removes include of <asm/cacheflush.h> and hence
discovers a few indirect inclusion and declaration problems as below.

  CC      arch/arm/mach-imx/hotplug.o
In file included from arch/arm/mach-imx/hotplug.c:16:0:
arch/arm/mach-imx/common.h:100:29: warning: ‘struct pt_regs’ declared inside parameter list [enabled by default]
arch/arm/mach-imx/common.h:100:29: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
arch/arm/mach-imx/common.h:101:29: warning: ‘struct pt_regs’ declared inside parameter list [enabled by default]
arch/arm/mach-imx/hotplug.c: In function ‘imx_cpu_die’:
arch/arm/mach-imx/hotplug.c:53:2: error: implicit declaration of function ‘cpu_do_idle’ [-Werror=implicit-function-declaration]
arch/arm/mach-imx/hotplug.c: In function ‘imx_cpu_kill’:
arch/arm/mach-imx/hotplug.c:58:26: error: ‘jiffies’ undeclared (first use in this function)
arch/arm/mach-imx/hotplug.c:58:26: note: each undeclared identifier is reported only once for each function it appears in
arch/arm/mach-imx/hotplug.c:58:2: error: implicit declaration of function ‘msecs_to_jiffies’ [-Werror=implicit-function-declaration]
arch/arm/mach-imx/hotplug.c:61:3: error: implicit declaration of function ‘time_after’ [-Werror=implicit-function-declaration]

Fix them by adding the needed inclusion and declaration.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NOlof Johansson <olof@lixom.net>

So it can be used in clk-imx6q.c for revision dependent clock tree setup.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

RBC is to control whether some ANATOP sub modules
can enter lpm mode when SOC is into STOP mode, if
RBC is enabled and PMIC_VSTBY_REQ is set, ANATOP
will have below behaviors:

1. Digital LDOs(CORE, SOC and PU) are bypassed;
2. Analog LDOs(1P1, 2P5, 3P0) are disabled;

As the 2P5 is necessary for DRAM IO pre-drive in
STOP mode, so we need to enable weak 2P5 in STOP
mode when 2P5 LDO is disabled.

For RBC settings, there are some rules as below
due to hardware design:

1. All interrupts must be masked during operating
   RBC registers;
2. At least 2 CKIL(32K) cycles is needed after the
   RBC setting is changed.
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Anatop module have sereval configurations for user
to reduce the power consumption in suspend, provide
suspend/resume interface for further use and enable
fet_odrive to reduce CORE LDO leakage during suspend.

As we have a common anatop file, remove all the operations
of anatop module in other files, use anatop interfaces to
do that.
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Commit a1f1c7ef (arm/imx6q: add suspend/resume support) added
declaration for a non-existing function pl310_get_save_ptr() by
mistake.  Remove it.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Commit 13eed989 (arm/imx6q: add device tree machine support) added
duplicated function declaration for imx_enable_cpu() and
imx_set_cpu_jump().  Remove them.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

There is a sync issue with hotplug operation.  It's possible that when
imx_cpu_kill gets running on primary core, the imx_cpu_die execution
on the core which is to be killed hasn't been finished yet.  The problem
will very likely be hit when running suspend without no_console_suspend
setting on kernel cmdline.

It uses cpu jumping argument register to sync imx_cpu_die and
imx_cpu_kill.  The register will be set in imx_cpu_die and imx_cpu_kill
will wait for the register being cleared to actually kill the cpu.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>

Add WAIT mode (ARM core clock gating) support to imx6q cpuidle driver.
As WAIT mode is broken on imx6q TO 1.0 and 1.1, it only enables the
support for revision 1.2 with chicken bit set.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Only mx508 based board is mach-mx50_rdp and it has been marked as BROKEN
for several releases.

mx508 currently lacks clock support.

In case someone needs to add mx508 support back, then the recommended approach
is to use device tree.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Use debug_ll_io_init() to map low level debug port for imx6q, so that
arch/arm/mach-imx/lluart.c can be removed.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

imx6q_clock_map_io() becomes an empty function since imx6q clock driver
is moved to common clock framework.  It's used nowhere now.  Remove it.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

It's buggy to disable the cpu that is being hot-unplugged in .cpu_die
hook which runs on the cpu itself.  Instead, it should be done in
.cpu_kill which runs on the thread (another cpu) that asks for shutting
down the cpu.  Move imx_enable_cpu(cpu, false) call into .cpu_kill
hook, and leave the cpu to be hot-unplugged in WFI within .cpu_die,
so that we can get a more stable cpu hot-plug operation.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Now that the GIC initialization sets up the handle_arch_irq pointer, we
can remove it for all machines and make it static.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Acked-by: NTony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Acked-by: NArnd Bergmann <arnd@arndb.de>

This adds a i.MX25 dt machine descriptor and changes the clock
support to optionally initialize from dt.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>

mxc_device_init() is a core_initcall function used to register devices
for mxc_aips_bus and mxc_ahb_bus, which are needed by gpio and dma
device registration.

Instead of being a core_initcall function, we have it called in soc
specific initialization function before gpio and dma devices get
registered, so that it will not be called for other platforms when
we enable multi-platform support for imx.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Rename mach-imx/include/mach/common.h to mach-imx/common.h and update
all users to include common.h rather than mach/common.h.

It also removes an unneeded inclusion to common.h in
mach-imx/devices/devices.c.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>

It's really unnecessary to have plat-mxc, and let's merge it into
mach-imx.  It's pretty much just a bunch of file renaming and
Kconfig/Makefile merge.

To make the change less invasive, we keep using Kconfig symbol
CONFIG_ARCH_MXC for mach-imx sub-architecture.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Convert the imx6q platform to use struct smp_operations to provide
its SMP and CPU hotplug operations.
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Acked-by: NNicolas Pitre <nico@linaro.org>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Now, imx51 device tree kernel calls pinctrl to set up pins.  The
function used to hook up non-DT pin setup is not needed for DT boot
any more.  Remove it from DT image.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Now imx53 is a device tree only platform, so the files and functions
used only by non-DT kernel can be removed.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Now, imx53 device tree kernel calls pinctrl to set up pins.  The
functions used to hook up non-DT pin setup is not needed for DT boot
any more.  Remove them from DT image.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This patch adds basic devicetree support for i.MX31 based SoCs.

Only the UART and interrupts bindings are added.
Signed-off-by: NDenis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add various functionality needed to enable a imx53 low power idle
state.  This includes adding the imx53 gpc_dvfs clock and making a
common imx5_late_init function and initializing all imx53
 MACHINE_STATE late_init calls to imx5_late_init.
Signed-off-by: NRobert Lee <rob.lee@linaro.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>