Avoid NULL dereference in setup_sge_queues() when the adapter is
in non offload mode.

Fixes: 0fbc81b3 ('chcr/cxgb4i/cxgbit/RDMA/cxgb4: Allocate resources dynamically for all cxgb4 ULD's')
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Each Octeon output ring can DMA packets to host memory in two modes:  info-
pointer mode and buffer-pointer-only mode.  In info-pointer mode, Octeon
takes two buffer pointers for each packet and places the length of the
packet along with specified number of bytes from the beginning of the
packet into one buffer and the rest of the packet in a separate buffer.  In
buffer-pointer-only mode, Octeon takes single buffer pointer and places the
length of the packet at the beginning of the buffer followed by the packet
data.

This patch switches all Octeon output rings from info-pointer mode to
buffer-pointer-only mode.  This results in fewer DMA setups and cache line
snoops.
Signed-off-by: NPrasad Kanneganti <pkanneganti@cavium.com>
Signed-off-by: NDerek Chickles <derek.chickles@cavium.com>
Signed-off-by: NSatanand Burla <satananda.burla@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add implementation to support ethtool -K ethX rx-vlan-filter on/off.
Rename OCTNET_CMD_ENABLE_VLAN_FILTER command to OCTNET_CMD_VLAN_FILTER_CTL
and add OCTNET_CMD_VLAN_FILTER_ENABLE and OCTNET_CMD_VLAN_FILTER_DISABLE
parameters so that it can be used to enable or disable the filter.
Signed-off-by: NPrasad Kanneganti <prasad.kanneganti@cavium.com>
Signed-off-by: NDerek Chickles <derek.chickles@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When booting into the kdump/kexec kernel, pHyp and vios
are not prepared for the initialization crq request and
a failover transport event is generated. This is not
handled correctly.

At this point in initialization the driver is still in
the 'probing' state and cannot handle a full reset of the
driver as is normally done for a failover transport event.

To correct this we catch driver resets while still in the
'probing' state and return EAGAIN. This results in the
driver tearing down the main crq and calling ibmvnic_init()
again.
Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cosmetic patch simplifying the smi read and write error paths. It also
align their error paths with the ones of the xsmi functions.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the xmdio xsmi interface support in the mvmdio driver.
This interface is used in Ethernet controllers on Marvell 370, 7k and 8k
(as of now). The xsmi interface supported by this driver complies with
the IEEE 802.3 clause 45. The xSMI interface is used by 10GbE devices.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a check for the read and write smi operations, to ensure the
MII_ADDR_C45 bit isn't set. This will be needed as soon as the xSMI
support is added to the mvmdio driver.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Put the two poll intervals (min and max) in the driver's ops
structure. This is needed to add the xmdio support later.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce an ops structure to add an indirection on the is_done
function, as this is needed to add the xMDIO support later.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MDIO layer already provides per-bus locking, so there's no need for
MDIO bus drivers to do their own internal locking.  Remove this.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cosmetic patch to use the GENMASK helper for masks.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cosmetic patch replacing spaces by tabs for defined values.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cosmetic fix reordering headers alphabetically.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to qede to report bpf_prog ID during XDP_QUERY_PROG.
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Cc: Mintz Yuval <Yuval.Mintz@cavium.com>
Acked-by: NAlexei Starovoitov <ast@fb.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to nfp to report bpf_prog ID during XDP_QUERY_PROG.
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NAlexei Starovoitov <ast@fb.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to ixgbe to report bpf_prog ID during XDP_QUERY_PROG.
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Acked-by: NAlexei Starovoitov <ast@fb.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to thunderx to report bpf_prog ID during XDP_QUERY_PROG.
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Cc: Sunil Goutham <sgoutham@cavium.com>
Acked-by: NAlexei Starovoitov <ast@fb.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to bnxt to report bpf_prog ID during XDP_QUERY_PROG.
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Acked-by: NAlexei Starovoitov <ast@fb.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to mlx5e to report bpf_prog ID during XDP_QUERY_PROG.
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: NAlexei Starovoitov <ast@fb.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to mlx4 to report bpf_prog ID during XDP_QUERY_PROG.
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: NAlexei Starovoitov <ast@fb.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.

Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:

    @@
    expression SKB, LEN;
    typedef u8;
    identifier fn = { skb_push, __skb_push, skb_push_rcsum };
    @@
    - *(fn(SKB, LEN))
    + *(u8 *)fn(SKB, LEN)

    @@
    expression E, SKB, LEN;
    identifier fn = { skb_push, __skb_push, skb_push_rcsum };
    type T;
    @@
    - E = ((T *)(fn(SKB, LEN)))
    + E = fn(SKB, LEN)

    @@
    expression SKB, LEN;
    identifier fn = { skb_push, __skb_push, skb_push_rcsum };
    @@
    - fn(SKB, LEN)[0]
    + *(u8 *)fn(SKB, LEN)

Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.

Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:

    @@
    expression SKB, LEN;
    typedef u8;
    identifier fn = { skb_put, __skb_put };
    @@
    - *(fn(SKB, LEN))
    + *(u8 *)fn(SKB, LEN)

    @@
    expression E, SKB, LEN;
    identifier fn = { skb_put, __skb_put };
    type T;
    @@
    - E = ((T *)(fn(SKB, LEN)))
    + E = fn(SKB, LEN)

which actually doesn't cover pskb_put since there are only three
users overall.

A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.

An spatch similar to the one for skb_put_zero() converts many
of the places using it:

    @@
    identifier p, p2;
    expression len, skb, data;
    type t, t2;
    @@
    (
    -p = skb_put(skb, len);
    +p = skb_put_data(skb, data, len);
    |
    -p = (t)skb_put(skb, len);
    +p = skb_put_data(skb, data, len);
    )
    (
    p2 = (t2)p;
    -memcpy(p2, data, len);
    |
    -memcpy(p, data, len);
    )

    @@
    type t, t2;
    identifier p, p2;
    expression skb, data;
    @@
    t *p;
    ...
    (
    -p = skb_put(skb, sizeof(t));
    +p = skb_put_data(skb, data, sizeof(t));
    |
    -p = (t *)skb_put(skb, sizeof(t));
    +p = skb_put_data(skb, data, sizeof(t));
    )
    (
    p2 = (t2)p;
    -memcpy(p2, data, sizeof(*p));
    |
    -memcpy(p, data, sizeof(*p));
    )

    @@
    expression skb, len, data;
    @@
    -memcpy(skb_put(skb, len), data, len);
    +skb_put_data(skb, data, len);

(again, manually post-processed to retain some comments)
Reviewed-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There were many places that my previous spatch didn't find,
as pointed out by yuan linyu in various patches.

The following spatch found many more and also removes the
now unnecessary casts:

    @@
    identifier p, p2;
    expression len;
    expression skb;
    type t, t2;
    @@
    (
    -p = skb_put(skb, len);
    +p = skb_put_zero(skb, len);
    |
    -p = (t)skb_put(skb, len);
    +p = skb_put_zero(skb, len);
    )
    ... when != p
    (
    p2 = (t2)p;
    -memset(p2, 0, len);
    |
    -memset(p, 0, len);
    )

    @@
    type t, t2;
    identifier p, p2;
    expression skb;
    @@
    t *p;
    ...
    (
    -p = skb_put(skb, sizeof(t));
    +p = skb_put_zero(skb, sizeof(t));
    |
    -p = (t *)skb_put(skb, sizeof(t));
    +p = skb_put_zero(skb, sizeof(t));
    )
    ... when != p
    (
    p2 = (t2)p;
    -memset(p2, 0, sizeof(*p));
    |
    -memset(p, 0, sizeof(*p));
    )

    @@
    expression skb, len;
    @@
    -memset(skb_put(skb, len), 0, len);
    +skb_put_zero(skb, len);

Apply it to the tree (with one manual fixup to keep the
comment in vxlan.c, which spatch removed.)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some code re-ordering, functionally equivalent.

- The !tx_info->inl check is evaluated anyway in both flows
  (common case/end case). Run it first, this might finish
  the flows earlier.
- dma_unmap calls are identical in both flows, get it out
  of the if block into the common area.

Performance tests:
Tested on ConnectX3Pro, Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz

Gain is too small to be measurable, no degradation sensed.
Results are similar for IPv4 and IPv6.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NSaeed Mahameed <saeedm@mellanox.com>
Cc: kernel-team@fb.com
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Define LOG_TXBB_SIZE, log of TXBB_SIZE, and use it with a shift
operation instead of a multiplication with TXBB_SIZE.
Operations are equivalent as TXBB_SIZE is a power of two.

Performance tests:
Tested on ConnectX3Pro, Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz

Gain is too small to be measurable, no degradation sensed.
Results are similar for IPv4 and IPv6.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NSaeed Mahameed <saeedm@mellanox.com>
Cc: kernel-team@fb.com
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Increase the default TX ring size (from 512 to 1024) to match
the RX ring size.
This gives the XDP TX ring a better chance to keep up with the
rate of its RX ring in case of a high load of XDP_TX actions.

Tested:
Ethtool counter rx_xdp_tx_full used to increase, after applying this
patch it stopped.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NSaeed Mahameed <saeedm@mellanox.com>
Cc: kernel-team@fb.com
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of having their own NAPIs, XDP TX completion queues get
polled within the corresponding RX NAPI.
This prevents any possible race on TX ring prod/cons indices,
between the context that issues the transmits (RX NAPI) and the
context that handles the completions (was previously done in
a separate NAPI).

This also improves performance, as it decreases the number
of NAPIs running on a CPU, saving the overhead of syncing
and switching between the contexts.

Performance tests:
Tested on ConnectX3Pro, Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
Single queue no-RSS optimization ON.

XDP_TX packet rate:
-------------------------------------
     | Before    | After     | Gain |
IPv4 | 12.0 Mpps | 13.8 Mpps |  15% |
IPv6 | 12.0 Mpps | 13.8 Mpps |  15% |
-------------------------------------
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NSaeed Mahameed <saeedm@mellanox.com>
Cc: kernel-team@fb.com
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several performance improvements in XDP TX datapath,
including:
- Ring a single doorbell for XDP TX ring per NAPI budget,
  instead of doing it per a lower threshold (was 8).
  This includes removing the flow of immediate doorbell ringing
  in case of a full TX ring.
- Compiler branch predictor hints.
- Calculate values in compile time rather than in runtime.

Performance tests:
Tested on ConnectX3Pro, Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
Single queue no-RSS optimization ON.

XDP_TX packet rate:
-------------------------------------
     | Before    | After     | Gain |
IPv4 | 10.3 Mpps | 12.0 Mpps |  17% |
IPv6 | 10.3 Mpps | 12.0 Mpps |  17% |
-------------------------------------
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NSaeed Mahameed <saeedm@mellanox.com>
Cc: kernel-team@fb.com
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several small code and performance improvements in stack TX datapath,
including:
- Compiler branch predictor hints.
- Minimize variables scope.
- Move tx_info non-inline flow handling to a separate function.
- Calculate data_offset in compile time rather than in runtime
  (for !lso_header_size branch).
- Avoid trinary-operator ("?") when value can be preset in a matching
  branch.

Performance tests:
Tested on ConnectX3Pro, Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz

Gain is too small to be measurable, no degradation sensed.
Results are similar for IPv4 and IPv6.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NSaeed Mahameed <saeedm@mellanox.com>
Cc: kernel-team@fb.com
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several small performance improvements in TX CQ polling,
including:
- Compiler branch predictor hints.
- Minimize variables scope.
- More proper check of cq type.
- Use boolean instead of int for a binary indication.

Performance tests:
Tested on ConnectX3Pro, Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz

Packet-rate tests for both regular stack and XDP use cases:
No noticeable gain, no degradation.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NSaeed Mahameed <saeedm@mellanox.com>
Cc: kernel-team@fb.com
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several small performance improvements in RX datapath,
including:
- Compiler branch predictor hints.
- Replace a multiplication with a shift operation.
- Minimize variables scope.
- Write-prefetch for packet header.
- Avoid trinary-operator ("?") when value can be preset in a matching
  branch.
- Save a branch by updating RX ring doorbell within
  mlx4_en_refill_rx_buffers(), which now returns void.

Performance tests:
Tested on ConnectX3Pro, Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
Single queue no-RSS optimization ON
(enable by ethtool -L <interface> rx 1).

XDP_DROP packet rate:
Same (28.1 Mpps), lower CPU utilization (from ~100% to ~92%).

Drop packets in TC:
-------------------------------------
     | Before    | After     | Gain |
IPv4 | 4.14 Mpps | 4.18 Mpps |   1% |
-------------------------------------

XDP_TX packet rate:
-------------------------------------
     | Before    | After     | Gain |
IPv4 | 10.1 Mpps | 10.3 Mpps |   2% |
IPv6 | 10.1 Mpps | 10.3 Mpps |   2% |
-------------------------------------
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NSaeed Mahameed <saeedm@mellanox.com>
Cc: kernel-team@fb.com
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid touching RX QP RSS context when loading with only
one RX ring, to allow optimized A0 RX steering.

Enable by:
- loading mlx4_core with module param: log_num_mgm_entry_size = -6.
- then: ethtool -L <interface> rx 1

Performance tests:
Tested on ConnectX3Pro, Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz

XDP_DROP packet rate:
-------------------------------------
     | Before    | After     | Gain |
IPv4 | 20.5 Mpps | 28.1 Mpps |  37% |
IPv6 | 18.4 Mpps | 28.1 Mpps |  53% |
-------------------------------------
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Cc: kernel-team@fb.com
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove owner argument, as it is obsolete and unused.
This also saves the overhead of calculating its value in data-path.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NSaeed Mahameed <saeedm@mellanox.com>
Cc: kernel-team@fb.com
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding a support to flush all HW resources with one FW command and
skip all the heavy unload flows of the driver on kernel shutdown.
There's no need to free all the SW context since a new fresh kernel
will be loaded afterwards.

Regarding the FW resources, they should be closed, otherwise we will
have leakage in the FW. To accelerate this flow, we execute one command
in the beginning that tells the FW that the driver isn't going to close
any of the FW resources and asks the FW to clean up everything.
Once the commands complete, it's safe to close the PCI resources and
finish the routine.
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Add a new interface for commands execution that allows the
caller to wait for the command's completion in a busy-wait
loop (polling mode).

This is useful if we want to execute a command in a polling mode
while the driver is working in events mode for the rest of
the commands.
This interface will be used in the downstream patches.
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Unlike ethtool stats, get_stats ndo provides information cached by
update stats work that is running in the background without updating
them explicitly.
We cannot update all counters inside the ndo because some
updates require firmware commands that cannot be performed under a
spinlock.

update_stats work does not need to update ALL counters, since only
some of them are needed by ndo_get_stats.
This patch will allow for a minimal run of update_stats using an extra
parameter which will update necessary counters only and cut 13
firmware commands in each iteration of the work.

Work duration previous to this patch: ~4200us.
Work duration after this patch: ~700us (17% of the original time).
Signed-off-by: NGal Pressman <galp@mellanox.com>
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Cc: kernel-team@fb.com

Move "query queue counter out of buffer" helper function out of
qp.c to en_main.c, since mlx5e netdev driver is the only one to use it.

Also allocate the output buffer on the stack instead of the heap, to reduce
number of heap allocs on update_stats work.
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Cc: kernel-team@fb.com

Allocating buffers on the heap every 200ms is something we should avoid,
let's use buffers located on the stack instead.
Signed-off-by: NGal Pressman <galp@mellanox.com>
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Cc: kernel-team@fb.com

Rename rx_symbol_errors_phy to rx_pcs_symbol_err_phy, in order to
prevent confusion with rx_symbol_err_phy counter.

rx_pcs_symbol_err_phy counter counts the number of symbol errors that
were detected on the PCS (regardless of traffic) and weren't
corrected by FEC correction algorithm or that FEC algorithm was
not active on this interface.

rx_symbol_err_phy refers to errors on packet level (physical error
during a packet receive).

Fixes: 5db0a4f6 ("net/mlx5e: Expose physical layer statistical...")
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Cc: kernel-team@fb.com