Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 26 9月, 2012 24 次提交
  3. 25 9月, 2012 3 次提交
    • P
      sh: pfc: Fix up GPIO mux type reconfig case. · 16d74ebe
      由 Paul Mundt 提交于 
      Some drivers need to switch pin states between GPIO and pin function at
runtime, which was inadvertently broken in the pinctrl driver for GPIOs
being bound to a specific direction.

This fixes up the request path to ensure that previously configured GPIOs
don't cause us to inadvertently error out with an unsupported mux on
reconfig, which in practice is primarily aimed at trapping pull-up/down
users that have yet to be implemented under the new API.

Fixes up regressions in the TPU PWM driver, amongst others.
Reported-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
      16d74ebe
    • M
      phy/micrel: Rename KS80xx to KSZ80xx · 510d573f
      由 Marek Vasut 提交于 
      There is no such part as KS8001, KS8041 or KS8051. There are only
KSZ8001, KSZ8041 and KSZ8051. Rename these parts as such to match
the Micrel naming.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: David J. Choi <david.choi@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Linux ARM kernel <linux-arm-kernel@lists.infradead.org>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      510d573f
    • M
      phy/micrel: Implement support for KSZ8021 · 212ea99a
      由 Marek Vasut 提交于 
      The KSZ8021 PHY was previously caught by KS8051, which is not correct.
This PHY needs additional setup if it is strapped for address 0. In such
case an reserved bit must be written in the 0x16, "Operation Mode Strap
Override" register. According to the KS8051 datasheet, that bit means
"PHY Address 0 in non-broadcast" and it indeed behaves as such on KSZ8021.
The issue where the ethernet controller (Freescale FEC) did not communicate
with network is fixed by writing this bit as 1.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: David J. Choi <david.choi@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      212ea99a
  5. 24 9月, 2012 5 次提交
    • S
      edac_mc: edac_mc_free() cannot assume mem_ctl_info is registered in sysfs. · faa2ad09
      由 Shaun Ruffell 提交于 
      Fix potential NULL pointer dereference in edac_unregister_sysfs() on
system boot introduced in 3.6-rc1.

Since commit 7a623c03 ("edac: rewrite the sysfs code to use struct
device") edac_mc_alloc() no longer initializes embedded kobjects in
struct mem_ctl_info.  Therefore edac_mc_free() can no longer simply
decrement a kobject reference count to free the allocated memory unless
the memory controller driver module had also called edac_mc_add_mc().

Now edac_mc_free() will check if the newly embedded struct device has
been registered with sysfs before using either the standard device
release functions or freeing the data structures itself with logic
pulled out of the error path of edac_mc_alloc().

The BUG this patch resolves for me:

  BUG: unable to handle kernel NULL pointer dereference at   (null)
  EIP is at __wake_up_common+0x1a/0x6a
  Process modprobe (pid: 933, ti=f3dc6000 task=f3db9520 task.ti=f3dc6000)
  Call Trace:
    complete_all+0x3f/0x50
    device_pm_remove+0x23/0xa2
    device_del+0x34/0x142
    edac_unregister_sysfs+0x3b/0x5c [edac_core]
    edac_mc_free+0x29/0x2f [edac_core]
    e7xxx_probe1+0x268/0x311 [e7xxx_edac]
    e7xxx_init_one+0x56/0x61 [e7xxx_edac]
    local_pci_probe+0x13/0x15
  ...

Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: NShaun Ruffell <sruffell@digium.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      faa2ad09
    • F
      edac_mc: fix messy kfree calls in the error path · ef6e7816
      由 Fengguang Wu 提交于 
      coccinelle warns about:

+ drivers/edac/edac_mc.c:429:9-23: ERROR: reference preceded by free on line 429

   421         if (mci->csrows) {
 > 422                 for (chn = 0; chn < tot_channels; chn++) {
   423                         csr = mci->csrows[chn];
   424                         if (csr) {
 > 425                                 for (chn = 0; chn < tot_channels; chn++)
   426                                          kfree(csr->channels[chn]);
   427                                  kfree(csr);
   428                          }
 > 429                          kfree(mci->csrows[i]);
   430                  }
   431                  kfree(mci->csrows);
   432          }

and that code block seem to mess things up in several ways (double free, memory
leak, out-of-bound reads etc.):

L422: The iterator "chn" and bound "tot_channels" are totally wrong. Should be
      "row" and "tot_csrows" respectively. Which means either memory leak, or
      out-of-bound reads (which if does not trigger an immediate page fault
      error, will further lead to kfree() on random addresses).

L425: The inner loop is reusing the same iterator "chn" as the outer loop,
      which could lead to premature end of the outer loop, and hence memory leak.

L429: The array index 'i' in mci->csrows[i] is a temporary value used in
      previous loops, and won't change at all in the current loop. Which
      means either out-of-bound read and possibly kfree(random number), or the
      same mci->csrows[i] get freed once and again, and possibly double free
      for the kfree(csr) in L427.

L426/L427: a kfree(csr->channels) is needed in between to avoid leaking the memory.

The buggy code was introduced by commit de3910eb ("edac: change the mem
allocation scheme to make Documentation/kobject.txt happy") in the 3.6-rc1
merge window. Fix it by freeing up resources in this order:

  free csrows[i]->channels[j]
  free csrows[i]->channels
  free csrows[i]
  free csrows

CC: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      ef6e7816
    • A
      hwmon: (fam15h_power) Tweak runavg_range on resume · 5f0ecb90
      由 Andreas Herrmann 提交于 
      The quirk introduced with commit
00250ec9 (hwmon: fam15h_power: fix
bogus values with current BIOSes) is not only required during driver
load but also when system resumes from suspend. The BIOS might set the
previously recommended (but unsuitable) initilization value for the
running average range register during resume.
Signed-off-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Tested-by: NAndreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@vger.kernel.org # 3.0+
      5f0ecb90
    • S
      hwmon: (coretemp) Use get_online_cpus to avoid races involving CPU hotplug · 641f1456
      由 Silas Boyd-Wickizer 提交于 
      coretemp_init loops with for_each_online_cpu, adding platform_devices
and sysfs interfaces, then calls register_hotcpu_notifier.  There is a
race if a CPU is offlined or onlined after the loop, but before
register_hotcpu_notifier.  The race might result in the absence of a
platform_device+sysfs interface for an online CPU, or the presence of
a platform_device+sysfs interface for an offline CPU.  A similar race
occurs during coretemp_exit, after the module calls
unregister_hotcpu_notifier, but before it unregisters all devices, a
CPU might offline and a device for an offline CPU will exist for a
short while.

This fix surrounds for_each_online_cpu and register_hotcpu_notifier
with get_online_cpus+put_online_cpus; and surrounds
unregister_hotcpu_notifier and device unregistering with
get_online_cpus+put_online_cpus.

Build tested.
Signed-off-by: NSilas Boyd-Wickizer <sbw@mit.edu>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
      641f1456
    • S
      hwmon: (via-cputemp) Use get_online_cpus to avoid races involving CPU hotplug · 1ec3ddfd
      由 Silas Boyd-Wickizer 提交于 
      via_cputemp_init loops with for_each_online_cpu, adding
platform_devices, then calls register_hotcpu_notifier.  If a CPU is
offlined between the loop and register_hotcpu_notifier, then later
onlined, via_cputemp_device_add will attempt to add platform devices
with the same ID.  A similar race occurs during via_cputemp_exit,
after the module calls unregister_hotcpu_notifier, a CPU might offline
and a device will exist for a CPU that is offline.

This fix surrounds for_each_online_cpu and register_hotcpu_notifier
with get_online_cpus+put_online_cpus; and surrounds
unregister_hotcpu_notifier and device unregistering with
get_online_cpus+put_online_cpus.

Build tested.
Signed-off-by: NSilas Boyd-Wickizer <sbw@mit.edu>
Acked-by: NHarald Welte <laforge@gnumonks.org>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
      1ec3ddfd
  7. 23 9月, 2012 3 次提交
  9. 22 9月, 2012 5 次提交