Introduce a common helper for the pattern of:
  - allocate new blob property
  - potentially free old blob property
  - replace content of indicative property with new blob ID
  - change member pointer on modeset object
Signed-off-by: NDaniel Stone <daniels@collabora.com>
Cc: Dave Airlie <airlied@redhat.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
[danvet: Squash in fixup from Daniel for the kerneldoc, reported by
0day builder.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Previously, when updating the path blob property, we would leak the
existing one. Make this symmetrical with the tile and EDID blob
pointers.
Signed-off-by: NDaniel Stone <daniels@collabora.com>
Cc: Dave Airlie <airlied@redhat.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

One failure path in crtc_helper had an open-coded CRTC state destroy
which didn't actually call through to the driver's specified state
destroy. Fix that.
Signed-off-by: NDaniel Stone <daniels@collabora.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

DMT Version 1.0, Rev. 13 lists a bunch of new modes we don't currently
have in our dmt mode table. So add them.

The order may look a bit weird since it's not sorted based on the DMT
ID, but this is the order they appear in the standard. I suppose they
are ordered by the resolution, pixel clock, or some such factor. I
decided that it's perhaps best to keep the same order as the spec.

Cc: "liu,lei" <lei.a.liu@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

To help with matching things to spec, include the DMT ID in the comments
in out DMT mode table.

Cc: "liu,lei" <lei.a.liu@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Liu Lei noticed that our 1856x1392@75Hz DMT mode doesn't match the spec.
Fix that up, and also fix up a few other inconsistencies I discovered
by parsing the spec (DMT version 1.0, revision 13) and comparing the
results to our current DMT mode table.

Also clean up the indentation mess for the 1024x768i mode.

Cc: "liu,lei" <lei.a.liu@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Completely different approach:  Instead of encoding each and every
framebuffer update as spice operation simply update the shadow
framebuffer and maintain a dirty rectangle.  Also schedule a worker
to push an update for the dirty rectangle as spice operation.  Usually
a bunch of dirty rectangle updates are collected before the worker
actually runs.

What changes:  Updates get batched now.  Instead of sending tons of
small updates a few large ones are sent.  When the same region is
updated multiple times within a short timeframe (scrolling multiple
lines for example) we send a single update only.  Spice server has an
easier job now:  The dependency tree for display operations which spice
server maintains for lazy rendering is alot smaller now.  Spice server's
image compression probably works better too with the larger image blits.

Net effect:  framebuffer console @ qxldrmfb is an order of magnitude
faster now.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

misc drm core patches.

* tag 'topic/drm-misc-2015-05-06' of git://anongit.freedesktop.org/drm-intel:
  drm: simplify master cleanup
  drm: simplify authentication management
  drm: drop unused 'magicfree' list
  drm: fix a memleak on mutex failure path
  drm/atomic-helper: Really recover pre-atomic plane/cursor behavior
  drm/qxl: Fix qxl_noop_get_vblank_counter()
  drm: Zero out invalid vblank timestamp in drm_update_vblank_count. (v2)
  drm: Prevent invalid use of vblank_disable_immediate. (v2)
  drm/vblank: Fixup and document timestamp update/read barriers
  DRM: Don't re-poll connector for disconnect
  drm: Fix for DP CTS test 4.2.2.5 - I2C DEFER handling
  drm: Fix the 'native defer' message in drm_dp_i2c_do_msg()
  drm/atomic-helper: Don't call atomic_update_plane when it stays off

In drm_master_destroy() we _free_ the master object. There is no reason to
hold any locks while dropping its static members, nor do we have to reset
it to 0.

Furthermore, kfree() already does NULL checks, so call it directly on
master->unique and drop the redundant reset-code.
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The magic auth tokens we have are a simple map from cyclic IDs to drm_file
objects. Remove all the old bulk of code and replace it with a simple,
direct IDR.

The previous behavior is kept. Especially calling authmagic multiple times
on the same magic results in EINVAL except on the first call. The only
difference in behavior is that we never allocate IDs multiple times as
long as a client has its FD open.

v2:
 - Fix return code of GetMagic()
 - Use non-cyclic IDR allocator
 - fix off-by-one in "magic > INT_MAX" sanity check

v3:
 - drop redundant "magic > INT_MAX" check
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This list is write-only. It's never used for read-access, so no reason to
keep it around. Drop it!
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Need to free just allocated ctx allocation if we cannot
get our config mutex.

This one has been flagged by kbuild bot all the way back in August,
but somehow nobody picked it up:
https://lists.01.org/pipermail/kbuild/2014-August/001691.html

In addition there is another failure path that leaks the same
ctx reference that is fixed.

Found with smatch.
Signed-off-by: NOleg Drokin <green@linuxhacker.ru>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I've fumbled this in

commit f02ad907
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Thu Jan 22 16:36:23 2015 +0100

    drm/atomic-helpers: Recover full cursor plane behaviour

and accidentally put the assignment for legacy_cursor_upate after the
atomic commit, where it is pretty useless.
Reported-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

This breaks under the vblank timestamp cleanup patch
by Daniel Vetter. Also it is pointless to return anything
but zero (or any other constant) if the function doesn't
actually query a hw vblank counter. The bogus return of
the current drm vblank counter via direct readout or via
drm_vblank_count() is found in many of the new kms drivers,
but it does exactly nothing different from returning any
arbitrary constant - it's a no operation.

Let's simply return 0 - Easy and fast.
Signed-off-by: NMario Kleiner <mario.kleiner.de@gmail.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since commit 844b03f2 we make
sure that after vblank irq off, we return the last valid
(vblank count, vblank timestamp) pair to clients, e.g., during
modesets, which is good.

An overlooked side effect of that commit for kms drivers without
support for precise vblank timestamping is that at vblank irq
enable, when we update the vblank counter from the hw counter, we
can't update the corresponding vblank timestamp, so now we have a
totally mismatched timestamp for the new count to confuse clients.

Restore old client visible behaviour from before Linux 3.18, but
zero out the timestamp at vblank counter update (instead of disable
as in original implementation) if we can't generate a meaningful
timestamp immediately for the new vblank counter. This will fix
this regression, so callers know they need to retry again later
if they need a valid timestamp, but at the same time preserves
the improvements made in the commit mentioned above.

v2: Rebased on top of Daniel Vetter's fixup and documentation
    patch for timestamp updates. Drop request for stable kernel
    backport as this would be more difficult, unless the original
    patch would get applied to stable kernels.
Signed-off-by: NMario Kleiner <mario.kleiner.de@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For a kms driver to support immediate disable of vblank
irq's reliably without introducing off by one errors or
other mayhem for clients, it must not only support a
hardware vblank counter query, but also high precision
vblank timestamping, so vblank count and timestamp can be
instantaneously reinitialzed to valid values. Additionally
the exposed hardware counter must behave as if it is
incrementing at leading edge of vblank to avoid off by
one errors during reinitialization of the counter while
the display happens to be inside or close to vblank.

Check during drm_vblank_init that a driver which claims to
be capable of vblank_disable_immediate at least supports
high precision timestamping and prevent use of instant
disable if that isn't present as a minimum requirement.

v2: Changed from DRM_ERROR to DRM_INFO and made message
    more clear, as suggested by Michel Dänzer.
Signed-off-by: NMario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: NMichel Dänzer <michel.daenzer@amd.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This was a bit too much cargo-culted, so lets make it solid:
- vblank->count doesn't need to be an atomic, writes are always done
  under the protection of dev->vblank_time_lock. Switch to an unsigned
  long instead and update comments. Note that atomic_read is just a
  normal read of a volatile variable, so no need to audit all the
  read-side access specifically.

- The barriers for the vblank counter seqlock weren't complete: The
  read-side was missing the first barrier between the counter read and
  the timestamp read, it only had a barrier between the ts and the
  counter read. We need both.

- Barriers weren't properly documented. Since barriers only work if
  you have them on boths sides of the transaction it's prudent to
  reference where the other side is. To avoid duplicating the
  write-side comment 3 times extract a little store_vblank() helper.
  In that helper also assert that we do indeed hold
  dev->vblank_time_lock, since in some cases the lock is acquired a
  few functions up in the callchain.

Spotted while reviewing a patch from Chris Wilson to add a fastpath to
the vblank_wait ioctl.

v2: Add comment to better explain how store_vblank works, suggested by
Chris.

v3: Peter noticed that as-is the 2nd smp_wmb is redundant with the
implicit barrier in the spin_unlock. But that can only be proven by
auditing all callers and my point in extracting this little helper was
to localize all the locking into just one place. Hence I think that
additional optimization is too risky.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Michel Dänzer <michel@daenzer.net>
Cc: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-and-tested-by: NMario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

Pull ext4 fixes from Ted Ts'o:
 "Some miscellaneous bug fixes and some final on-disk and ABI changes
  for ext4 encryption which provide better security and performance"

* tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix growing of tiny filesystems
  ext4: move check under lock scope to close a race.
  ext4: fix data corruption caused by unwritten and delayed extents
  ext4 crypto: remove duplicated encryption mode definitions
  ext4 crypto: do not select from EXT4_FS_ENCRYPTION
  ext4 crypto: add padding to filenames before encrypting
  ext4 crypto: simplify and speed up filename encryption

Pull drm fixes from Dave Airlie:
 "One intel fix, one rockchip fix, and a bunch of radeon fixes for some
  regressions from audio rework and vm stability"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/i915/chv: Implement WaDisableShadowRegForCpd
  drm/radeon: fix userptr return value checking (v2)
  drm/radeon: check new address before removing old one
  drm/radeon: reset BOs address after clearing it.
  drm/radeon: fix lockup when BOs aren't part of the VM on release
  drm/radeon: add SI DPM quirk for Sapphire R9 270 Dual-X 2G GDDR5
  drm/radeon: adjust pll when audio is not enabled
  drm/radeon: only enable audio streams if the monitor supports it
  drm/radeon: only mark audio as connected if the monitor supports it (v3)
  drm/radeon/audio: don't enable packets until the end
  drm/radeon: drop dce6_dp_enable
  drm/radeon: fix ordering of AVI packet setup
  drm/radeon: Use drm_calloc_ab for CS relocs
  drm/rockchip: fix error check when getting irq
  MAINTAINERS: add entry for Rockchip drm drivers

Just a single intel fix
* tag 'drm-intel-fixes-2015-04-30' of git://anongit.freedesktop.org/drm-intel:
  drm/i915/chv: Implement WaDisableShadowRegForCpd

one fix and maintainers update
* 'drm-next0420' of https://github.com/markyzq/kernel-drm-rockchip:
  drm/rockchip: fix error check when getting irq
  MAINTAINERS: add entry for Rockchip drm drivers

Pull SCSI fixes from James Bottomley:
 "This is three logical fixes (as 5 patches).

  The 3ware class of drivers were causing an oops with multiqueue by
  tearing down the command mappings after completing the command (where
  the variables in the command used to tear down the mapping were
  no-longer valid).  There's also a fix for the qnap iscsi target which
  was choking on us sending it commands that were too long and a fix for
  the reworked aha1542 allocating GFP_KERNEL under a lock"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  3w-9xxx: fix command completion race
  3w-xxxx: fix command completion race
  3w-sas: fix command completion race
  aha1542: Allocate memory before taking a lock
  SCSI: add 1024 max sectors black list flag

Pull slave dmaengine fixes from Vinod Koul:
 "Here are the fixes in dmaengine subsystem for rc2:

   - privatecnt fix for slave dma request API by Christopher

   - warn fix for PM ifdef in usb-dmac by Geert

   - fix hardware dependency for xgene by Jean"

* 'next' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: increment privatecnt when using dma_get_any_slave_channel
  dmaengine: xgene: Set hardware dependency
  dmaengine: usb-dmac: Protect PM-only functions to kill warning

Pull powerpc fixes from Michael Ellerman:
 - build fix for SMP=n in book3s_xics.c
 - fix for Daniel's pci_controller_ops on powernv.
 - revert the TM syscall abort patch for now.
 - CPU affinity fix from Nathan.
 - two EEH fixes from Gavin.
 - fix for CR corruption from Sam.
 - selftest build fix.

* tag 'powerpc-4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
  powerpc/powernv: Restore non-volatile CRs after nap
  powerpc/eeh: Delay probing EEH device during hotplug
  powerpc/eeh: Fix race condition in pcibios_set_pcie_reset_state()
  powerpc/pseries: Correct cpu affinity for dlpar added cpus
  selftests/powerpc: Fix the pmu install rule
  Revert "powerpc/tm: Abort syscalls in active transactions"
  powerpc/powernv: Fix early pci_controller_ops loading.
  powerpc/kvm: Fix SMP=n build error in book3s_xics.c

The estimate of necessary transaction credits in ext4_flex_group_add()
is too pessimistic. It reserves credit for sb, resize inode, and resize
inode dindirect block for each group added in a flex group although they
are always the same block and thus it is enough to account them only
once. Also the number of modified GDT block is overestimated since we
fit EXT4_DESC_PER_BLOCK(sb) descriptors in one block.

Make the estimation more precise. That reduces number of requested
credits enough that we can grow 20 MB filesystem (which has 1 MB
journal, 79 reserved GDT blocks, and flex group size 16 by default).
Signed-off-by: NJan Kara <jack@suse.cz>
Signed-off-by: NTheodore Ts'o <tytso@mit.edu>
Reviewed-by: NEric Sandeen <sandeen@redhat.com>

fallocate() checks that the file is extent-based and returns
EOPNOTSUPP in case is not. Other tasks can convert from and to
indirect and extent so it's safe to check only after grabbing
the inode mutex.
Signed-off-by: NDavide Italiano <dccitaliano@gmail.com>
Signed-off-by: NTheodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org

Currently it is possible to lose whole file system block worth of data
when we hit the specific interaction with unwritten and delayed extents
in status extent tree.

The problem is that when we insert delayed extent into extent status
tree the only way to get rid of it is when we write out delayed buffer.
However there is a limitation in the extent status tree implementation
so that when inserting unwritten extent should there be even a single
delayed block the whole unwritten extent would be marked as delayed.

At this point, there is no way to get rid of the delayed extents,
because there are no delayed buffers to write out. So when a we write
into said unwritten extent we will convert it to written, but it still
remains delayed.

When we try to write into that block later ext4_da_map_blocks() will set
the buffer new and delayed and map it to invalid block which causes
the rest of the block to be zeroed loosing already written data.

For now we can fix this by simply not allowing to set delayed status on
written extent in the extent status tree. Also add WARN_ON() to make
sure that we notice if this happens in the future.

This problem can be easily reproduced by running the following xfs_io.

xfs_io -f -c "pwrite -S 0xaa 4096 2048" \
          -c "falloc 0 131072" \
          -c "pwrite -S 0xbb 65536 2048" \
          -c "fsync" /mnt/test/fff

echo 3 > /proc/sys/vm/drop_caches
xfs_io -c "pwrite -S 0xdd 67584 2048" /mnt/test/fff

This can be theoretically also reproduced by at random by running fsx,
but it's not very reliable, though on machines with bigger page size
(like ppc) this can be seen more often (especially xfstest generic/127)
Signed-off-by: NLukas Czerner <lczerner@redhat.com>
Signed-off-by: NTheodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org

This patch removes duplicated encryption modes which were already in
ext4.h. They were duplicated from commit 3edc18d8 and commit f542fb.

Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Michael Halcrow <mhalcrow@google.com>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Signed-off-by: NChanho Park <chanho61.park@samsung.com>
Signed-off-by: NTheodore Ts'o <tytso@mit.edu>

This patch adds a tristate EXT4_ENCRYPTION to do the selections
for EXT4_FS_ENCRYPTION because selecting from a bool causes all
the selected options to be built-in, even if EXT4 itself is a
module.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NTheodore Ts'o <tytso@mit.edu>

Pull networking fixes from David Miller:

 1) Receive packet length needs to be adjust by 2 on RX to accomodate
    the two padding bytes in altera_tse driver.  From Vlastimil Setka.

 2) If rx frame is dropped due to out of memory in macb driver, we leave
    the receive ring descriptors in an undefined state.  From Punnaiah
    Choudary Kalluri

 3) Some netlink subsystems erroneously signal NLM_F_MULTI.  That is
    only for dumps.  Fix from Nicolas Dichtel.

 4) Fix mis-use of raw rt->rt_pmtu value in ipv4, one must always go via
    the ipv4_mtu() helper.  From Herbert Xu.

 5) Fix null deref in bridge netfilter, and miscalculated lengths in
    jump/goto nf_tables verdicts.  From Florian Westphal.

 6) Unhash ping sockets properly.

 7) Software implementation of BPF divide did 64/32 rather than 64/64
    bit divide.  The JITs got it right.  Fix from Alexei Starovoitov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (30 commits)
  ipv4: Missing sk_nulls_node_init() in ping_unhash().
  net: fec: Fix RGMII-ID mode
  net/mlx4_en: Schedule napi when RX buffers allocation fails
  netxen_nic: use spin_[un]lock_bh around tx_clean_lock
  net/mlx4_core: Fix unaligned accesses
  mlx4_en: Use correct loop cursor in error path.
  cxgb4: Fix MC1 memory offset calculation
  bnx2x: Delay during kdump load
  net: Fix Kernel Panic in bonding driver debugfs file: rlb_hash_table
  net: dsa: Fix scope of eeprom-length property
  net: macb: Fix race condition in driver when Rx frame is dropped
  hv_netvsc: Fix a bug in netvsc_start_xmit()
  altera_tse: Correct rx packet length
  mlx4: Fix tx ring affinity_mask creation
  tipc: fix problem with parallel link synchronization mechanism
  tipc: remove wrong use of NLM_F_MULTI
  bridge/nl: remove wrong use of NLM_F_MULTI
  bridge/mdb: remove wrong use of NLM_F_MULTI
  net: sched: act_connmark: don't zap skb->nfct
  trivial: net: systemport: bcmsysport.h: fix 0x0x prefix
  ...

Here the "other side" refers to the guest or host.
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With my job change kernel work will be "own time"; I'm keeping lguest
and modules (and the virtio standards work), but virtio kernel has to
go.

This makes it clear that Michael is in charge.  He's good, but having
me watch over his shoulder won't help.

Good luck Michael!
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull Ceph RBD fix from Sage Weil.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  rbd: end I/O the entire obj_request on error

If we don't do that, then the poison value is left in the ->pprev
backlink.

This can cause crashes if we do a disconnect, followed by a connect().
Tested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Reported-by: NWen Xu <hotdog3645@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we end I/O struct request with error, we need to pass
obj_request->length as @nr_bytes so that the entire obj_request worth
of bytes is completed.  Otherwise block layer ends up confused and we
trip on

    rbd_assert(more ^ (which == img_request->obj_request_count));

in rbd_img_obj_callback() due to more being true no matter what.  We
already do it in most cases but we are missing some, in particular
those where we don't even get a chance to submit any obj_requests, due
to an early -ENOMEM for example.

A number of obj_request->xferred assignments seem to be redundant but
I haven't touched any of obj_request->xferred stuff to keep this small
and isolated.

Cc: Alex Elder <elder@linaro.org>
Cc: stable@vger.kernel.org # 3.10+
Reported-by: NShawn Edwards <lesser.evil@gmail.com>
Reviewed-by: NSage Weil <sage@redhat.com>
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

This obscures the length of the filenames, to decrease the amount of
information leakage.  By default, we pad the filenames to the next 4
byte boundaries.  This costs nothing, since the directory entries are
aligned to 4 byte boundaries anyway.  Filenames can also be padded to
8, 16, or 32 bytes, which will consume more directory space.

Change-Id: Ibb7a0fb76d2c48e2061240a709358ff40b14f322
Signed-off-by: NTheodore Ts'o <tytso@mit.edu>

Avoid using SHA-1 when calculating the user-visible filename when the
encryption key is available, and avoid decrypting lots of filenames
when searching for a directory entry in a directory block.

Change-Id: If4655f144784978ba0305b597bfa1c8d7bb69e63
Signed-off-by: NTheodore Ts'o <tytso@mit.edu>

Pull btrfs fixes from Chris Mason:
 "A few more btrfs fixes.

  These range from corners Filipe found in the new free space cache
  writeback to a grab bag of fixes from the list"

* 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: btrfs_release_extent_buffer_page didn't free pages of dummy extent
  Btrfs: fill ->last_trans for delayed inode in btrfs_fill_inode.
  btrfs: unlock i_mutex after attempting to delete subvolume during send
  btrfs: check io_ctl_prepare_pages return in __btrfs_write_out_cache
  btrfs: fix race on ENOMEM in alloc_extent_buffer
  btrfs: handle ENOMEM in btrfs_alloc_tree_block
  Btrfs: fix find_free_dev_extent() malfunction in case device tree has hole
  Btrfs: don't check for delalloc_bytes in cache_save_setup
  Btrfs: fix deadlock when starting writeback of bg caches
  Btrfs: fix race between start dirty bg cache writeout and bg deletion

Pull arm64 fixes from Will Deacon:
 "Not too much here, but we've addressed a couple of nasty issues in the
  dma-mapping code as well as adding the halfword and byte variants of
  load_acquire/store_release following on from the CSD locking bug that
  you fixed in the core.

   - fix perf devicetree warnings at probe time

   - fix memory leak in __dma_free()

   - ensure DMA buffers are always zeroed

   - show IRQ trigger in /proc/interrupts (for parity with ARM)

   - implement byte and halfword access for smp_{load_acquire,store_release}"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: perf: Fix the pmu node name in warning message
  arm64: perf: don't warn about missing interrupt-affinity property for PPIs
  arm64: add missing PAGE_ALIGN() to __dma_free()
  arm64: dma-mapping: always clear allocated buffers
  ARM64: Enable CONFIG_GENERIC_IRQ_SHOW_LEVEL
  arm64: add missing data types in smp_load_acquire/smp_store_release