The generic PHY framewrok expects different properties than the
old USB PHY framework. Supply those properties.

Fixes USB OTG port on GAT04 and N900 after the Generic PHY framework was
merged in greg/usb-next. [1]

[1] - https://lkml.org/lkml/2013/9/27/581Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

This adds devicetree for gta04 (Openmoko next generation board) with necessary
support for mmc, usb, leds and button.
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

IGEP boards have a number of LED connected to OMAP or TWL GPIO
lines. The actual wiring is different on each board so each board
DT has need to configure the mux correctly.

Even though it works with the current DT, the kernel complains with:

[2.305023] leds-gpio leds.18: pins are not configured from the driver

Add an empty pinmux_leds_pins pinctrl child node so boards can
override with the correct mux configuration and not depend on
default values for the GPIO LEDs to work.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add pinmux configuration for MCBSP2 connected to the TDM interface.
With this configuration the Headset modules works as expected.
Signed-off-by: NEnric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: NJavier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

On most OMAP3 platforms, the twl4030 IRQ line is connected to the
SYS_NIRQ line on OMAP.  Add another DTS include file
(twl4030_omap3.dtsi) for boards that hook up the twl4030 this way
to include.

This allows RTC wake from off-mode to work again on OMAP3-based
platforms with twl4030.  Tested on 3530/Beagle, 3730/Beagle-xM,
3530/Overo, 3730/Overo-STORM.

Special thanks to Florian Vaussard for suggesting use of preprocessor
feature.

Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Using constants for pinctrl allows a better readability, and removes
redundancy with comments.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Replace /include/ by #include for OMAP2+ DT, in order to use the
C pre-processor, making use of #define features possible.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

The IGEPv2 board has an SMSC LAN9221i ethernet chip connected to
the OMAP3 processor though the General-Purpose Memory Controller.

This patch adds a device node for the ethernet chip as a GPMC child
and all its dependencies (regulators, GPIO and pin muxs).
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add DT OPP table for OMAP34xx/35xx family of devices. This data is
decoded by OF with of_init_opp_table() helper function.

OPP data here is based on existing opp3xxx_data.c

Since the omap36xx OPP tables would be different from OMAP34xx/35xx,
introduce an new omap34xx.dtsi for 34xx/35xx specific entries and use
existing omap3.dtsi as the common dtsi file for all OMAP3 platforms.

This is in preparation to use generic cpufreq-cpu0 driver for device
tree enabled boot. Legacy non device tree enabled boot continues to
use omap-cpufreq.c and opp3xxx_data.c.
Signed-off-by: NNishanth Menon <nm@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

This is a follow-up to Javier Martinez effort adding initial
device tree support to IGEP technology devices [1].

It adds uart1 and uart2 bindings to the generic dtsi for the IGEP boards.

[1] http://www.spinics.net/lists/linux-omap/msg83409.htmlSigned-off-by: NMatthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add a generic .dtsi device tree source file for the
common characteristics across IGEP Technology devices.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: NMatthias Brugger <matthias.bgg@gmail.com>
Tested-by: NEnric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>