Does nothing, so trivial conversion. But update the outdated comment
while at it.
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Try to decypher detection failures is a little tricker at the moment as
the only indicator of progress is when output_poll_execute() tells us
the result after the connector->detect() has run. This patch adds a
telltale to the start of each detect function so that we can track
progress and associate activity more clearly with each connector.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I.e. for letter/pillarboxing. For those cases we need to adjust the
mode a bit, but Jesse gmch pfit refactoring in

commit 2dd24552
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Thu Apr 25 12:55:01 2013 -0700

    drm/i915: factor out GMCH panel fitting code and use for eDP v3

broke that by reordering the computation of the gmch pfit state with
the block of code that prepared the adjusted mode for it and told the
modeset core not to overwrite the adjusted mode with default settings.

We might want to switch around the core code to just fill in defaults,
but this code predates the pipe_config modeset rework. And in the old
crtc helpers we did not have a suitable spot to do this.

Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Hans de Bruin <jmdebruin@xmsnet.nl>
Reported-and-tested-by: NHans de Bruin <jmdebruin@xmsnet.nl>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's in the PFIT_CONTROL register, but very much associated with the
lvds encoder. So move the readout for it (in the case of an otherwise
disabled pfit) from the pipe to the lvds encoder's get_config
function.

Otherwise we get a pipe state mismatch if we use pipe B for a non-lvds
output and we've left the dither bit enabled behind us. This can
happen if the BIOS has set the bit (some seem to unconditionally do
that, even in the complete absence of an lvds port), but not enabled
pipe B at boot-up. Then we won't clear the pfit control register since
we can only touch that if the pfit is associated with our pipe in the
crtc configuration - we could trample over the pfit state of the other
pipe otherwise since it's shared. Once pipe B is enabled we notice
that the 6to8 dither bit is set and complain about the mismatch.

Note that testing indicates that we don't actually need to set this
bit when the pfit is disabled, dithering on 18bpp panels seems to work
regardless. But ripping that code out is not something for a bugfix
meant for -rc kernels.

v2: While at it clarify the logic in i9xx_get_pfit_config, spurred by
comments from Chris on irc.

v3: Use Chris suggestion to make the control flow in
i9xx_get_pfit_config easier to understand.

v4: Kill the extra line, spotted by Chris.
Reported-by: NKnut Petersen <Knut_Petersen@t-online.de>
Cc: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
References: http://lists.freedesktop.org/archives/intel-gfx/2013-July/030092.htmlTested-by: NKnut Petersen <Knut_Petersen@t-online.de>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This replaceable mainboard only has a VGA-out, yet it claims to also have
a connected LVDS header.

Addresses https://bugs.freedesktop.org/show_bug.cgi?id=65256Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reported-by: NCornel Panceac <cpanceac@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <annndddrr@gmail.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This replaceable mainboard only has a VGA-out, yet it claims to also have
a connected LVDS header.

Addresses https://bugs.freedesktop.org/show_bug.cgi?id=63860

[jani.nikula@intel.com: use DMI_EXACT_MATCH for board name.]
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reported-by: <annndddrr@gmail.com>
Cc: Cornel Panceac <cpanceac@gmail.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

i9xx doesn't use pre_enable at all, so we can fold this in now.
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Lots of bangin my head against the wall^UExperiments have shown that
we really need to enable the lvds port before we enable plls. Strangely
that seems to include the fdi rx pll on the pch.

Note that the pch pll assert can fire since the lvds port has it's own
special clock source settings in the DPLL register, which means it
will never have a shared dpll (since there's only one LVDS port).

Anyway, encode this new evidence with a few nice WARNs.

v2: Incorporate review comments from Imre.
- Explain why lvds can't have a shared dpll.
- Update the WARN output.

Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Nowadays (i.e. with Valleyview) we also have edp on non-PCH_SPLIT
platforms, so just checking for LVDS is not good enough.

Secondly we have full pfit pipe config tracking, so we'll correctly
disable the pfit as part of the initial modeset.

For fastboot we need a bit of work here to correctly kill unsupported
configs (if e.g. the pfit is used on anything else than the built-in
panel). But since that's not yet supported we don't need to worry.
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Only lvds/tv did actually check for cloning or not, but many more
places should.

Notices because my ivb tried to enable both cpu edp and vga on the
first crtc - the resulting confusion between has_pch_encoder,
has_dp_encoder but not actually being a pch dp encoder resulting in
hilarity (hitting a BUG).

We _really_ need an igt to random-walk our modeset space more
exhaustively.

The bug seems to have been exposed due to a race in the hw load
detection support for VGA: Right after a hotplug VGA was still
detected as connected, but obviously reading the EDID wasn't possible
any more. Hence why restarting X a bit later fixed things. Due to the
1024x756 fallback resolution suddenly more outputs had the same
resolution.

On top of that SNA was confused with the possible_clones mask, trying
to clone outputs which cannot be cloned. That bug is now fixed with

commit fc1e0702b25e647cb423851fb7228989fec28bd6
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Wed May 29 11:25:28 2013 +0100

    sna: fixup up possible_clones kms->X impedance mismatch

v2: Kill intel_encoder_check_is_cloned, spotted by Paulo.

v3: Drop the now unused pipe param.

v4: Kill the stray printk Chris spotted.

v5: Elaborate on how the bug in userspace happened and why it was racy
to reproduce.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Last year, a patch was made for the "HP t5740e Thin Client" (see
http://lists.freedesktop.org/archives/dri-devel/2012-May/023245.html).
This device reports an lvds panel, but does not really have one.

The predecessor of this device is the "hp t5740", which also does not have
an lvds panel. This patch will add the same quirk for this device.
Signed-off-by: NBen Mesman <ben@bnc.nl>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We can use this for fetching encoder specific pipe_config state, like
mode flags, adjusted clock, etc.

Just used for mode flags atm, so we can check the pipe config state at
mode set time.

v2: get_config when checking hw state too
v3: fix DVO and LVDS mode flags (Ville)
    get SDVO DTD for flag fetch (Ville)
v4: use input timings (Ville)
    correct command used (Ville)
    remove gen4 check (Ville)
v5: get DDI flag config too
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v4)
Tested-by: Paulo Zanoni <przanoni@gmail.com> (the new hsw ddi stuff)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Pfit state readout is a bit ugly on gen2/3 due to the intermingling
with the lvds state, but alas.

Also note that since state is always cleared to zero we can
unconditonally compare all the state and completely neglect the actual
platform we're running on.

v2: Properly check for the pfit power domain on haswell.

v3: Don't check pgm_ratios on gen4+, they're auto-computed by the hw.

v4: Properly clear the lvds border bits, upset the state checker a
bit.

v5: Unconditionally read out panel dither settings on gen2/3.
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

drm_i915_private is getting bigger and bigger when adding new vbt stuff.
So, the better way of getting drm_i915_private organized is to create
a special structure for vbt stuff.

v2: Basically conflicts fixes
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Writing hw registers from compute_config?
Just say no!

In this case not too horrible since we write a constant 0, and only
debugging would put something else in there. But while checking that
code I've noticed that this register disappeared on pch platforms, so
fix that up, too.

And adjust the comment a bit, it's outdated.
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

pipe_config is the new dev_priv!

More seriously, this is actually better since a pipe_config can be
thrown away if the modeset compute config stage fails. Whereas any
state stored in dev_prive needs to be painstakingly restored, since
otherwise a dpms off/on will wreak massive havoc. Yes, that even
applies to state only used in ->mode_set callbacks, since we need to
call those even for dpms on when the Haswell power well cleared
everything out.
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

So on a bunch of setups we only have 2 fdi lanes available, e.g. hsw
VGA or 3 pipes on ivb. And seemingly a lot of modes don't quite fit
into this, among them the default 1080p mode.

The solution is to dither down the pipe a bit so that everything fits,
which this patch implements.

But ports compute their state under the assumption that the bpp they
pick will be the one selected, e.g. the display port bw computations
won't work otherwise. Now we could adjust our code to again up-dither
to the computed DP link parameters, but that's pointless.

So instead when the pipe needs to adjust parameters we need to retry
the pipe_config computation at the encoder stage. Furthermore we need
to inform encoders that they should not increase bandwidth
requirements if possible. This is required for the hdmi code, which
prefers the pipe to up-dither to either of the two possible hdmi bpc
values.

LVDS has a similar requirement, although that's probably only
theoretical in nature: It's unlikely that we'll ever see an 8bpc
high-res lvds panel (which is required to hit the 2 fdi lane limit).

eDP is the only thing which could increase the pipe_bpp setting again,
even when in the retry-loop. This could hit the WARN. Two reasons for
not bothering:
- On many eDP panels we'll get a black screen if the bpp settings
  don't match vbt. So failing the modeset is the right thing to do.
  But since that also means it's the only way to light up the panel,
  it should work. So we shouldn't be able to hit this WARN.
- There are still opens around the eDP panel handling, and maybe we
  need additional tricks. Before that happens it's imo no use trying
  to be too clever.
Worst case we just need to kill that WARN or maybe fail the compute
config stage if the eDP connector can't get the bpp setting it wants.
And since this can only happen with an fdi link in between and so for
pch eDP panels it's rather unlikely to blow up, if ever.

v2: Rebased on top of a bikeshed from Paulo.

v3: Improve commit message around eDP handling with the stuff
things with Imre.
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

And put the pfit stuff into substructs while we're at it.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This gets the panel fitter working on eDP on VLV, and should also apply
to eDP panels on G4x chipsets (if we ever detect and mark an all-in-one
panel as eDP anyway).

A few cleanups are still possible on top of this, for example the LVDS
border control could be placed in the LVDS encoder structure and updated
based on the result of the panel fitter calculation.

Multi-pipe fitting isn't handled correctly either if we ever get a config
that wants to try the panel fitter on more than one output at a time.

v2: use pipe_config for storing pfit values (Daniel)
    add i9xx_pfit_enable function for use by 9xx and VLV (Daniel)
v3: fixup conflicts and lvds_dither check
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: fix up botched conflict resolution from Jesse:
- border = LVDS_BORDER_ENABLE was lost for CENTER scaling
- comment about gen2/3 panel fitter scaling was lost
- dev_priv->lvds_dither reintroduced.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Up to now we've relied on the bios to get this right for us. Let's try
out whether our code has improved a bit, since we should dither
always when the output bpp doesn't match the plane bpp.
- gen5+ should be fine, since we only use the bios hint as an upgrade.
- gen4 changes, since here dithering is still controlled in the lvds
  register.
- gen2/3 has implicit dithering depeding upon whether you use 2 or 3
  lvds pairs (which makes sense, since it only supports 8bpc pipe
  outpu configurations).
- hsw doesn't support lvds.

v2: Remove redudant dither setting.

v3: Completly drop reliance on dev_priv->lvds_dither.

v4: Enable dithering on gen2/3 only when we have a 18bpp panel, since
up-dithering to a 24bpp panel is not supported by the hw. Spotted by
Ville.

v5: Also only enable lvds port dithering on gen4 for 18bpp modes. In
practice this only excludes dithering a 10bpc plane down for a 24bpp
lvds panel. Not something we truly care about. Again noticed by Ville.

v6: Actually git add.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We can only enable the pfit if the pipe is disabled. Ensure that this
is obeyed with a neat assert.

Also check whether the pfit is off before enabling it - if not we've
lost track of things somewhere since the pfit is only ever used by the
lvds output.

v2: Fix spell fail in the commit message pointed out by Ville&Jani.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Backlight cleanup in the eDP connector destroy callback caused the
backlight device to be removed on some systems that first initialized LVDS
and then attempted to initialize eDP. Prevent multiple backlight
initializations, and ensure backlight cleanup is only done once by moving
it to modeset cleanup.

A small wrinkle is the introduced asymmetry in backlight
setup/cleanup. This could be solved by adding refcounting, but it seems
overkill considering that there should only ever be one backlight device.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=55701Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Tested-by: NPeter Verthez <peter.verthez@skynet.be>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The "Mobile Sandy Bridge CPUs" in the Fujitsu Esprimo Q900
mini desktop PCs are probably misleading the LVDS detection
code in intel_lvds_supported. Nothing is connected to the
LVDS ports in these systems.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The procedure has now 3 steps:

1. Compute the bpp that the plane will output, this is done in
   pipe_config_set_bpp and stored into pipe_config->pipe_bpp. Also,
   this function clamps the pipe_bpp to whatever limit the EDID of any
   connected output specifies.
2. Adjust the pipe_bpp in the encoder and crtc functions, according to
   whatever constraints there are.
3. Decide whether to use dither by comparing the stored plane bpp with
   computed pipe_bpp.

There are a few slight functional changes in this patch:
- LVDS connector are now also going through the EDID clamping. But in
  a 2nd change we now unconditionally force the lvds bpc value - this
  shouldn't matter in reality when the panel setup is consistent, but
  better safe than sorry.
- HDMI now forces the pipe_bpp to the selected value - I think that's
  what we actually want, since otherwise at least the pixelclock
  computations are wrong (I'm not sure whether the port would accept
  e.g. 10 bpc when in 12bpc mode). Contrary to the old code, we pick
  the next higher bpc value, since otherwise there's no way to make
  use of the 12 bpc mode (since the next patch will remove the 12bpc
  plane format, it doesn't exist).

Both of these changes are due to the removal of the

	pipe_bpp = min(display_bpp, plane_bpp);

statement.

Another slight change is the reworking of the dp bpc code:
- For the mode_valid callback it's sufficient to only check whether
  the mode would fit at the lowest bpc.
- The bandwidth computation code is a bit restructured: It now walks
  all available bpp values in an outer loop and the codeblock that
  computes derived values (once a good configuration is found) has been
  moved out of the for loop maze. This is prep work to allow us to
  successively fall back on bpc values, and also correctly support bpc
  values != 8 or 6.

v2: Rebased on top of Paulo Zanoni's little refactoring to use more
drm dp helper functions.

v3: Rebased on top of Jani's eDP bpp fix and Ville's limited color
range work.

v4: Remove the INTEL_MODE_DP_FORCE_6BPC #define, no longer needed.

v5: Remove intel_crtc->bpp, too, and fix up the 12bpc check in the
hdmi code. Also fixup the bpp check in intel_dp.c, it'll get reworked
in a later patch though again.

v6: Fix spelling in a comment.

v7: Debug output improvements for the bpp computation.

v8: Fixup 6bpc lvds check - dual-link and 8bpc mode are different
things!

v9: Reinstate the fix to properly ignore the firmware edp bpp ... this
was lost in a rebase.

v10: Both g4x and vlv lack 12bpc pipes, so don't enforce that we have
that. Still unsure whether this is the way to go, but at least 6bpc
for a 8bpc hdmi output seems to work.

v11: And g4x/vlv also lack 12bpc hdmi support, so only support high
depth on DP. Adjust the code.

v12: Rebased.

v13: Split out the introduction of pipe_config->dither|pipe_bpp, as
requested from Jesse Barnes.

v14: Split out the special 6BPC handling for DP, as requested by Jesse
Barnes.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is used way too often in the enable/disable paths. And will
be even more useful in the future.

Note that correct semantics of this change highly depend upon
correct updating of intel_crtc->config: Like with all other
modeset state, we need to call ->disable with the old config,
but ->mode_set and ->enable with the new config.

v2: Do not yet use the flag in the ->disable callbacks - atm we don't
yet have support for the information stored in the pipe_config in the
hw state readout code, so this will be wrong at boot-up/resume.

v3: Rebased on top of the hdmi/dp ddi encoder merging.

v4: Fixup stupid rebase error which lead to a NULL vfunc deref.

v5: On haswell the VGA port is on the PCH!

v6: s/IS_HASWELL/HAS_DDI/, spotted by Paulo Zanoni. Also add a missing
parameter name in a function declaration.

v7: Don't forget to git add ...
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Only used by the lvds encoder. Note that we shouldn't do the same
simple conversion with the FORCE_6BPC flag, since that's much better
handled by moving all the pipe_bpc computation around.

This requires that we pass the pipe config around to encoders, so
that they can set special attributes and set constraints. To do so
introduce a new ->compute_config encoder callback, which is called in
stead of the drm crtc helper's ->mode_fixup.

To avoid massive churn all over the codebase we don't want to convert
all existing ->mode_fixup functions. Instead I've opted to convert
them on an as-needed basis (mostly to cut down on rebase conflicts and
to have more freedom to experiment around while developing the
patches).
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now it returns false for all platforms unless they're explicitly
listed on the function. There should be no real difference, except for
the fact that it now returns false on Haswell.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With the previous patch "drm/i915: disable shared panel fitter for
pipe" we now disable the panel fitter at the right spot in the modeset
sequence in the crtc functions on all platforms. Hence the disabling
in intel_disable_lvds is no longer required and potentially harmful
(since the plane is still enabled at this point).

Similarly on the enabling side we enable the panel fitter in the lvds
callback only once the plane is enabled. Which is too late. Hence move
this into a new intel_pre_enable_lvds callback.

Finally we can ditch lvds_encoder->pfit_dirty - this was required to
work around the crtc helper semantics, but with the new i915 modeset
infrastructure we should enable/disable the pfit only when enabling or
disabling the entire output pipeline. So separate state tracking for
the pfit is no longer required.
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
[danvet: Bikeshed the commit message a bit to stress that now we
enable/disable the pfit on i9xx platforms at the right point of time
compared to the old code.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

i915 driver needs to do modeset when
1. system resumes from sleep
2. lid is opened

In PM_SUSPEND_MEM state, all the GPEs are cleared when system resumes,
thus it is the i915_resume code does the modeset rather than intel_lid_notify().

But in PM_SUSPEND_FREEZE state, this will be broken because
system is still responsive to the lid events.
1. When we close the lid in Freeze state, intel_lid_notify() sets modeset_on_lid.
2. When we reopen the lid, intel_lid_notify() will do a modeset,
   before the system is resumed.
here is the error log,

[92146.548074] WARNING: at drivers/gpu/drm/i915/intel_display.c:1028 intel_wait_for_pipe_off+0x184/0x190 [i915]()
[92146.548076] Hardware name: VGN-Z540N
[92146.548078] pipe_off wait timed out
[92146.548167] Modules linked in: hid_generic usbhid hid snd_hda_codec_realtek snd_hda_intel snd_hda_codec parport_pc snd_hwdep ppdev snd_pcm_oss i915 snd_mixer_oss snd_pcm arc4 iwldvm snd_seq_dummy mac80211 snd_seq_oss snd_seq_midi fbcon tileblit font bitblit softcursor drm_kms_helper snd_rawmidi snd_seq_midi_event coretemp drm snd_seq kvm btusb bluetooth snd_timer iwlwifi pcmcia tpm_infineon i2c_algo_bit joydev snd_seq_device intel_agp cfg80211 snd intel_gtt yenta_socket pcmcia_rsrc sony_laptop agpgart microcode psmouse tpm_tis serio_raw mxm_wmi soundcore snd_page_alloc tpm acpi_cpufreq lpc_ich pcmcia_core tpm_bios mperf processor lp parport firewire_ohci firewire_core crc_itu_t sdhci_pci sdhci thermal e1000e
[92146.548173] Pid: 4304, comm: kworker/0:0 Tainted: G        W    3.8.0-rc3-s0i3-v3-test+ #9
[92146.548175] Call Trace:
[92146.548189]  [<c10378e2>] warn_slowpath_common+0x72/0xa0
[92146.548227]  [<f86398b4>] ? intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548263]  [<f86398b4>] ? intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548270]  [<c10379b3>] warn_slowpath_fmt+0x33/0x40
[92146.548307]  [<f86398b4>] intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548344]  [<f86399c2>] intel_disable_pipe+0x102/0x190 [i915]
[92146.548380]  [<f8639ea4>] ? intel_disable_plane+0x64/0x80 [i915]
[92146.548417]  [<f8639f7c>] i9xx_crtc_disable+0xbc/0x150 [i915]
[92146.548456]  [<f863ebee>] intel_crtc_update_dpms+0x5e/0x90 [i915]
[92146.548493]  [<f86437cf>] intel_modeset_setup_hw_state+0x42f/0x8f0 [i915]
[92146.548535]  [<f8645b0b>] intel_lid_notify+0x9b/0xc0 [i915]
[92146.548543]  [<c15610d3>] notifier_call_chain+0x43/0x60
[92146.548550]  [<c105d1e1>] __blocking_notifier_call_chain+0x41/0x80
[92146.548556]  [<c105d23f>] blocking_notifier_call_chain+0x1f/0x30
[92146.548563]  [<c131a684>] acpi_lid_send_state+0x78/0xa4
[92146.548569]  [<c131aa9e>] acpi_button_notify+0x3b/0xf1
[92146.548577]  [<c12df56a>] ? acpi_os_execute+0x17/0x19
[92146.548582]  [<c12e591a>] ? acpi_ec_sync_query+0xa5/0xbc
[92146.548589]  [<c12e2b82>] acpi_device_notify+0x16/0x18
[92146.548595]  [<c12f4904>] acpi_ev_notify_dispatch+0x38/0x4f
[92146.548600]  [<c12df0e8>] acpi_os_execute_deferred+0x20/0x2b
[92146.548607]  [<c1051208>] process_one_work+0x128/0x3f0
[92146.548613]  [<c1564f73>] ? common_interrupt+0x33/0x38
[92146.548618]  [<c104f8c0>] ? wake_up_worker+0x30/0x30
[92146.548624]  [<c12df0c8>] ? acpi_os_wait_events_complete+0x1e/0x1e
[92146.548629]  [<c10524f9>] worker_thread+0x119/0x3b0
[92146.548634]  [<c10523e0>] ? manage_workers+0x240/0x240
[92146.548640]  [<c1056e84>] kthread+0x94/0xa0
[92146.548647]  [<c1060000>] ? ftrace_raw_output_sched_stat_runtime+0x70/0xf0
[92146.548652]  [<c15649b7>] ret_from_kernel_thread+0x1b/0x28
[92146.548658]  [<c1056df0>] ? kthread_create_on_node+0xc0/0xc0

three different modeset flags are introduced in this patch
MODESET_ON_LID_OPEN: do modeset on next lid open event
MODESET_DONE:  modeset already done
MODESET_SUSPENDED:  suspended, only do modeset when system is resumed

In this way,
1. when lid is closed, MODESET_ON_LID_OPEN is set so that
   we'll do modeset on next lid open event.
2. when lid is opened, MODESET_DONE is set
   so that duplicate lid open events will be ignored.
3. when system suspends, MODESET_SUSPENDED is set.
   In this case, we will not do modeset on any lid events.

Plus, locking mechanism is also introduced to avoid racing.
Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that the driver is in control of whether it needs to disable
everything at take-over or not, we can rip this all out.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Two exceptions:
- debugfs files only read information which is not related to crtc, so
  can stay on the modeset_config lock.
- Same holds for the edp vdd work in intel_dp.c. Add a corresponding
  WARN_ON and a comment next to the intel_dp struct fields for
  documentation.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This reverts commit 9756fe38.

The bogus lvds output is actually a lvds->hdmi bridge, which we don't
really support. But unconditionally disabling it breaks some existing
setups.
Reported-by: NJohn Tapsell <johnflux@gmail.com>
References: http://permalink.gmane.org/gmane.comp.freedesktop.xorg.drivers.intel/17237Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Note: This patch also adds a little helper intel_crtc_restore_mode for
the common case where we do a full modeset but with the same
parameters, e.g. to undo bios damage or update a property.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Added note.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Only two things needed adjustment:
- pipe select for PCH_CPT
- There's no dithering bit on ilk+ in the lvds ctl reg
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

A few things needed to change:
- HAS_PCH_SPLIT since ilk+ is not yet converted to this.
- s/LVDS/intel_lvds->reg/ to prep for ilk conversion
- replace the clock.p2 == 7 check with a is_dual_link check
- s/adjusted_mode/intel_lvds->fixed_mode

v2: Rebase on top of Jani Nikula's panel rework. I'm wondering whether
we shouldn't add an attached_panel pointer to intel_encoder, to
replace the encoder private ->attached_connector pointers, since
that's essentially what we need.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

To ditch at least some of the PCH_SPLIT ? PCH_LVDS : LVDS code ...

v2: Rebase on top of Jani Nikula's panel rework.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Yeah, all users (both the clock selection special cases and the lvds
pin pair stuff) are still in common code, but this will change.

v2: Rebase on top of Jani Nikula's panel rework.

v3: Incorporate review from Paulo Zanoni:
- s/__is_dual_link_lvds/compute_is_dual_link_lvds
- kill dev_priv->lvds_val
- drop spurious whitespace change

v4: Add a debug printk to display the dual-link status, as suggested
by Paulo Zanoni in review.

Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v3)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Just a prep patch to make this a property of intel_lvds. Makes more
sense, removes clutter from intel_display.c and eventually I want to
move all the encoder special cases wrt clock handling to encoders
anyway.

v2: Add an intel_ prefixe to is_dual_link_lvds since it's non-static
now.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There seem to be indeed some awkwards machines around, mostly those
without OpRegion support, where the firmware changes the display hw
state behind our backs when closing the lid.

This force-restore logic has been originally introduced in

commit c1c7af60
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Thu Sep 10 15:28:03 2009 -0700

    drm/i915: force mode set at lid open time

but after the modeset-rework we've disabled it in the vain hope that
it's no longer required:

commit 3b7a89fc
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Mon Sep 17 22:27:21 2012 +0200

    drm/i915: fix OOPS in lid_notify

Alas, no.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=54677
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=57434Tested-by: NKrzysztof Mazur <krzysiek@podlesie.net>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>