Most of the time, the issues we want to debug with the
firmware dump mechanism are transient. It is then very
hard to stop the recording on time and get meaningful
data.
In order to solve this, I add here an infrastucture
of triggers. The user will supply a list of triggers
that will start / stop the recording. We have two types
of triggers: start and stop. Start triggers can start a
specific configuration. The stop triggers will be able to
kick the collection of the data with the currently running
configuration. These triggers are given to the driver by
the .ucode file - just like the configuration.

In the next patches, I'll add triggers in the code.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

20 ms fragments are no longer required by system.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This is useful to debug weird antenna problems.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Packet Level Co-Running is a BT Coex feature which is
supported on certain devices only, hence the need for
a TLV flag for it.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We shouldn't call iwl_mvm_d3_disconnect_iter() on the running
interfaces when we are woken up due to net-detect, because it doesn't
make sense.  Additionally, this seems to set the
IEEE80211_SDATA_DISCONNECT_RESUME flag that will cause a disconnection
on the next resume (if a normal WoWLAN is used).

To solve this, skip the iteration loop when net-detect is set.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reported-by: NSamuel Tan <samueltan@chromium.org>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The new API slightly changes the layout of the version of
the firmware - prepare for that.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Report the average beacon signal and the number of received beacons as
measured by the firmware.

Since the firmware just counts, and doesn't reset the counter at all,
clear it in the firmware whenever we associate. However, accumulate it
over firmware restart.

Since clearing the statistics in the firmware will also clear the ones
for the radio statistics, add those to the accumulator when cleared.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Due to HW bug in the DBGC when driver want to stop the dbg recording it
should wait 100us before collecting the data instead of write 0 to
DBGC_OUT_CTRL.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The legacy scan API is deprecated and not used anymore with 10 and
higher firmware versions.  Since we deprecated firmware version 9, we
can remove a whole lot of unused code.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This firmware is not supported anymore.  Stop loading this firmware.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Export the radio statistics from the statistics v10 API (if the
firmware also has the capability to fill these statistics) using
the global survey data facility.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

New firmware versions will report statistics using a new version 10
of the API, instead of the current version 8. Add support for this.
This enables getting beacon and radio statistics.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows to use the firmware debugging system even when
the configuration values are set hard coded in the firmware.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Cleanup unused code.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The shared antenna should be forbidden to use only if there's
high BT activity. Comparing to BT_OFF was effectively causing
us to always forbid using the shared antenna for SISO. This
leads to degraded performance in scenarios where the shared
antenna would have better performance.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add this to the info printed when reading rate_scale_table.
Useful for debugging.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

ss_force is a debugging option to force a certain single stream
tx mode. It's not useful if it gets reset after tx idle. Fix that.
While at it also make sure any code touching ss_force will only
get compiled if debugfs support is configured.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Newer devices have more PAPD channel groups.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When a TDLS station is being drained its Tx queues are still in use. Don't
allocate them to a different station in the meantime.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Due to issues with Miracast adapters MIMO reception disable
use of MIMO when for low latency P2P traffic.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Once the FW supports autonomous decision between STBC/BFER/SISO
we no longer set the STBC bit and ANT_AB in the rate table.
However the FW rate in the tx response will have the STBC
or BFER bit set and the antennas set to ANT_AB in case these
were chosen by it. This will cause us to discard any such
response as unmatching the current LQ table and thus break
the rs search cycle completely.
Fix this by relaxing the rate matching in case we're working
with the new API and STBC/BFER are used.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The check to avoid the shared antenna was passed the wrong
antenna parameter. It should have checked whether the antenna of
the next column we're considering is allowed and instead it was
passed the current antenna.
This could lead to a wrong choice of the next column in the rs
algorithm and non optimal performance.

Fixes: commit 219fb66b ("iwlwifi: mvm: rs - don't use the shared antenna when BT load is high")
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently rs uses the info in mac80211 tx status which is
a translation of the actual rate coming up from the FW in
the tx response. This is matched up against the LQ table first
rate to make sure this tx frame used the current LQ table.
Instead of using the translated mac80211 info it's easier and
cleaner to just pass the actual tx response rate in the driver
private data and use that for matching.
This becomes even more important once the FW begins to
decide on its own whether to use STBC/BFER/SISO.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Provide a file creation function that also takes an initial size so that the
caller doesn't have to set i_size, thus meaning that we don't have to call
deal with ->d_inode in the callers.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NMichael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NAND-tree is used to check wiring between MAC and PHY using NAND gates
on the PHY side, hence the name.

NAND-tree initial status is latched at reset by probing the IRQ pin.
However some devices are sharing the PHY IRQ pin with other peripherals
such as Atmel SAMA5D[34]x-EK boards when using the optional TM7000
display module, therefore they are switching the PHY in NAND-tree test
mode depending on the current IRQ line status at reset.

This patch ensure PHY is not in NAND-tree test mode for all Micrel PHYs
using IRQ line as a NAND-tree toggle mode at reset.
Signed-off-by: NSylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a capability which let the hw could change the settings
automatically when the power change to ON. However, the USB reset
would reset the settings to the hw default, so the driver has to
restore the relative settings. Otherwise, it would influence the
functions of the hw, and the compatibility for the USB hub and
USB host controller.

The relative settings are as following.
 - set the power down scale to 96.
 - enable the power saving function of USB 2.0.
 - disable the ALDPS of ECM mode.
 - set burst mode depending on the burst size.
 - enable the flow control of endpoint full.
 - set fifo empty boundary to 32448 bytes.
 - enable the function of exiting LPM when Rx OK occurs.
 - set the connect timer to 1.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch "module: fix types of device tables aliases" newly requires that
invocations of

MODULE_DEVICE_TABLE(type, name);

come *after* the definition of `name'.  That is reasonable, but some
drivers weren't doing this.  Fix them.

Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Andrey Ryabinin <a.ryabinin@samsung.com>
Cc: David Miller <davem@davemloft.net>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

printk and friends can now format bitmaps using '%*pb[l]'.  cpumask
and nodemask also provide cpumask_pr_args() and nodemask_pr_args()
respectively which can be used to generate the two printf arguments
necessary to format the specified cpu/nodemask.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

printk and friends can now format bitmaps using '%*pb[l]'.  cpumask
and nodemask also provide cpumask_pr_args() and nodemask_pr_args()
respectively which can be used to generate the two printf arguments
necessary to format the specified cpu/nodemask.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If skb allocation fails once the IP header has been received, the rx state is
being set to WAIT_SYNC. The logic, though, shouldn't directly return, as the
buffer may contain a full packet, and therefore the WAIT_SYNC state needs to be
processed (resetting state to WAIT_IP, clearing rx_buf_size and re-initializing
rx_buf_missing).

So, just let the while loop continue so that in the next iteration the WAIT_SYNC
state cleanly stops the loop. The WAIT_SYNC processing will be done just after
that, only if the end of packet is flagged.
Signed-off-by: NAleksander Morgado <aleksander@aleksander.es>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cosmetic patch to add __percpu qualifier to pcpu_stats
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tg3_init_one() calls tg3_halt() without tp->lock despite its assumption
and causes deadlock.
If lockdep is enabled, a warning like this shows up before the stall:

  [ BUG: bad unlock balance detected! ]
  3.19.0test #3 Tainted: G            E
  -------------------------------------
  insmod/369 is trying to release lock (&(&tp->lock)->rlock) at:
  [<ffffffffa02d5a1d>] tg3_chip_reset+0x14d/0x780 [tg3]
  but there are no more locks to release!

tg3_init_one() doesn't call tg3_halt() under normal situation but
during kexec kdump I hit this problem.

Fixes: 932f19de ("tg3: Release tp->lock before invoking synchronize_irq()")
Signed-off-by: NJun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On Northstar (Broadcom's ARM architecture) we need to manually enable
all cores. Code for that is already in place, but the condition for it
was wrong.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver keeps adding multicast addresses without deleting removed MACs and
worrying about adapters filter limit. This results into actual count of programmed
multicast addresses get accumulated over the time and overruns the adapter's
filter limit without putting device in ACCEPT_ALL_MULTI mode. This causes
newly added multicast traffic to fail after the sequence of addition - deletion
in certain pattern.

This issue is seen only when netdev's mcast list count is less than adapters
mcast filter limit.

e.g. If adapters multicast filter limit is 38 per function
     then following sequence would result in multicast traffic failure for
     newly added MACs.
     - add less than 38 multicast MACs
     - remove previously added multicast MACs
     - add new multicast MACs (less than 38)
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code failed to configure the page size for architectures with page
size different than 4K - PPC for example.
Signed-off-by: NCarol L Soto <clsoto@us.ibm.com>
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch unclones an skb for the case where the sunvnet driver needs to
change the segmentation size so that it doesn't interfere with TCP SACK's
use of them.
Signed-off-by: NDavid L Stevens <david.stevens@oracle.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces the use of functions setup_timer
and mod_timer.

This is done using Coccinelle and semantic patch used
for this as follows:

// <smpl>
@@
expression x,y,z,a,b;
@@

-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);

// </smpl>
Signed-off-by: NVaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If CONFIG_NET_XGENE=y but CONFIG_OF=n:

drivers/net/ethernet/apm/xgene/xgene_enet_main.c:1033: warning: ‘xgene_enet_of_match’ defined but not used
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is only an API consolidation and should make things more readable.
Converting milliseconds to jiffies by "val * HZ / 1000" is technically
OK but msecs_to_jiffies(val) is the cleaner solution and handles all
corner cases correctly. This is a minor API cleanup only.
Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org>
Acked-by: NMark Einon <mark.einon@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>