Mostly just simple conversions:
  * ray_cs had bogus return of NET_TX_LOCKED but driver
    was not using NETIF_F_LLTX
  * hostap and ipw2x00 had some code that returned value
    from a called function that also had to change to return netdev_tx_t
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the queued management work items are processed in
ieee80211_sta_work() an item could be removed. This could change the
anybusy from true to false, so we better check whether we can start a
new scan only after having processed the pending work first.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When an interface is taken down while a scan is
pending -- i.e. a scan request was accepted but
not yet acted upon due to other work being in
progress -- we currently do not properly cancel
that scan and end up getting stuck. Fix this by
doing better checks when an interface is taken
down.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

An integer overflow in the minstrel debug code prevented the
throughput to be displayed correctly. This patch fixes that,
by permutating operations like proposed by Pavel Roskin.
Signed-off-by: NArnd Hannemann <hannemann@nets.rwth-aachen.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In mac80211's RX path some of the warnings that
warn about drivers passing invalid status values
leak the skb, fix that by refactoring the code.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I noticed that the throughput field of the minstrel_rate struct is never used,
so remove it.
Signed-off-by: NArnd Hannemann <hannemann@nets.rwth-aachen.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Due to the way the tasklets work in mac80211 there's
no need to ever disable them.

However, we need to clear the pending packets when
taking down the last interface because otherwise
the tx_pending_tasklet might be queued if the
driver mucks with the queues (which it shouldn't).

I've had a situation occasionally with ar9170 in
which ksoftirq was using 100% CPU time because
a disabled tasklet was scheduled, and I think that
was due to ar9170 receiving a packet while the
tasklet was disabled. That's strange and it really
should not do that for other reasons, but there's
no need to waste that much CPU time over it, it
should just warn instead.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With the libipw naming scheme change, it is no longer necessary for
mac80211 to avoid the ieee80211_rx name clash.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since configure_filter can sleep now, any multicast
configuration needed to be postponed to a work struct.
This, however, lead to a problem that we could queue
the work, stop the device and then afterwards invoke
configure_filter which may lead to driver hangs and is
a bug. To fix this, we can just cancel the filter work
since it's unnecessary to do after stopping the hw.

Since there are various places that call drv_stop, and
two of them do very similar things, the code for them
can be put into a shared function at the same time.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Reported-by: NLennert Buytenhek <buytenh@wantstofly.org>
Tested-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The mesh config information element has changed significantly since draft 1.08
This patch brings it up to date.

Thanks to Sam Leffler and Rui Paulo for identifying this.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"cfg80211: fix alignment problem in scan request"
introduced a bug into the error path, because now
we allocate the entire scan request and not just
the channel list (the channel list is allocated
together with the scan request) -- on errors we
thus also need to free the entire scan request.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This expands on the current fwded_frames stat counter which should be equal to
the total of these two new counters.  The new counters are called "fwded_mcast"
and "fwded_unicast".
Signed-off-by: NDaniel Walker <dwalker@fifo99.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CC [M]  net/mac80211/rc80211_pid_algo.o
net/mac80211/rc80211_pid_algo.c: In function ‘rate_control_pid_rate_init’:
net/mac80211/rc80211_pid_algo.c:304: warning: unused variable ‘si’
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Mesh uses the tx failure average to compute the (m)path metric.  This used to
be done inside the rate control module.  This patch breaks the dependency
between the mesh stack and the rate control algorithm.  Mesh will now work
independently of the chosen rate control algorithm.

The mesh stack keeps a moving average of the average transmission losses for
each mesh peer station.  If the fail average exceeds a certain threshold, the
peer link is marked as broken.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All but two drivers have now stopped using the two
deprecated members radio_enabled and beacon_int,
so it's about time to remove them for good.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NKalle Valo <kalle.valo@iki.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Over time, a whole bunch of drivers have come up
with their own scheme to delay the configure_filter
operation to a workqueue. To be able to simplify
things, allow configure_filter to sleep, and add
a new prepare_multicast callback that drivers that
need the multicast address list implement. This new
callback must be atomic, but most drivers either
don't care or just calculate a hash which can be
done atomically and then uploaded to the hardware
non-atomically.

A cursory look suggests that at76c50x-usb, ar9170,
mwl8k (which is actually very broken now), rt2x00,
wl1251, wl1271 and zd1211 should make use of this
new capability.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The length of the fixed portion of plink confirm frames is 4 bytes longer than
the other plink_action frames.  This path corrects an error in the length
adjustment done for these type of frames.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If a PREQ frame is received giving us a fresher DSN than what we have, record
the new dsn and mark it as valid.  This patch fixes a bug in the setting of the
MESH_PATH_DSN_VALID flag.

Also, minor fix to coding style on that file.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Mesh frames that could not be immediately resolved were queued with a NULL
info->control.vif.  This patch moves the call to mesh_nexthop_lookup closer to
the point where it is handed over to ieee80211_tx().  This ensures that the
unresolved frames are ready to be sent once the path is resolved.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This prevents calling rcu_synchronize from within the tx path by moving the
table growth code to the mesh workqueue.

Move mesh_table_free and mesh_table_grow from mesh.c to mesh_pathtbl.c and
declare them static.

Also, re-enable mesh in Kconfig and update the configuration description.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Tested-by: NAndrey Yurovsky <andrey@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The mesh stack was enabling beaconing without specifying an interval.  This
patch defines a default beaconing interval of 1s.

Incidentally, this fixes mesh beaconing in mac80211_hwsim devices.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This change triggers a path discovery as soon as the link quality degrades
below a certain threshold.  This results in a faster path recovery time than
by simply relying on the periodic path refresh mechanism to detect broken
links.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The fail_avg value is used to compute the mesh metric, and was only being set
by the pid rate control module. This fixes the mesh path selection mechanism
for cards that use mistrel for rate control.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The 11s task group recently changed the frame mesh multicast/broadcast frame
format to use 3-address.  This was done to avoid interactions with widely
deployed lazy-WDS access points.

This patch changes the format of group addressed frames, both mesh-originated
and proxied, to use the data format defined in draft D2.08 and forward.  The
address fields used for group addressed frames is:

In 802.11 header
 ToDS:0  FromDS:1
 addr1: DA  (broadcast/multicast address)
 addr2: TA
 addr3: Mesh SA

In address extension header:
 addr4: SA  (only present if frame was proxied)

Note that this change breaks backward compatibility with earlier mesh stack
versions.
Signed-off-by: NAndrey Yurovsky <andrey@cozybit.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On locally originated traffic, we refresh active paths after a timeout.  The
decision to do this was using the wrong sign and therefore the refresh timer
was triggered for every frame.
Signed-off-by: NAndrey Yurovsky <andrey@cozybit.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also, fix typo in comment.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Tested-by: NAndrey Yurovsky <andrey@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It's really easier to read if it's not indented
as much, so invert the condition and rearrange
the code so the smaller chunk is indented instead.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's no need to mask the variable with 0xFFF0
since we ever only use it as a u16 and the lowest
four bits can't ever be non-zero. The compiler
cannot infer the latter, and therefore has to emit
code to do the masking.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When encryption is used, the number of bytes
sent to the peer increases by the IV and ICV.
This is accounted if software encryption is
used, but not if the devices does hardware
encryption. To make the numbers comparable,
never account for that overhead.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The memory layout for scan requests was rather wrong,
we put the scan SSIDs before the channels which could
lead to the channel pointers being unaligned in memory.
It turns out that using a pointer to the channel array
isn't necessary anyway since we can embed a zero-length
array into the struct.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If we have a lot of frames to transmit at once, for
instance with fragmentation, it can be an optimisation
to only tell the DMA engine about them on the last
fragment/frame to avoid banging the IO too much. This
patch allows implementation such an optimisation by
telling the driver when more frames can be expected.

Currently, this is used by mac80211 only on fragmented
frames, but could also be used in the future on other
frames when the queue was full and there are multiple
frames pending.

Note that drivers need to be careful when using this
flag, they need to kick their DMA engines not just
when this flag is clear, but also when the queue gets
full so that progress can be made.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order for userspace to be able to figure out whether
it obtained a consistent snapshot of data or not when
using netlink dumps, we need to have a generation number
in each dump message that indicates whether the list has
changed or not -- its value is arbitrary.

This patch adds such a number to all dumps, this needs
some mac80211 involvement to keep track of a generation
number to start with when adding/removing mesh paths or
stations.

The wiphy and netdev lists can be fully handled within
cfg80211, of course, but generation numbers need to be
stored there as well.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After being disassociated by the AP, mac80211 currently
reports this to cfg80211, and then goes to delete the
association. That's fine, but cfg80211 assumes that it's
still authenticated, however, mac80211 throws away all
state.

This fixes mac80211 to keep track of the authentication
in that case so that cfg80211 can request a deauth or
new association properly.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Mesh is currently disabled on mac80211, its marked
as broken. This patch gets it to compile though,
to account for the mac80211 workqueue changes.
There was a simple typo in the patches for mesh
for the workqueue migration, but we never compile
tested it as we couldn't even select mesh as its
broken. Lets at least let it compile for those
interested in getting it fixed.
Reported-by: NPat Erley <pat-lkml@erley.org>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We splice skbs from the pending queue for a TID
onto the local pending queue when tearing down a
block ack request. This is not necessary unless we
actually have received a request to start a block ack
request (rate control, for example). If we never received
that request we should not be splicing the tid pending
queue as it would be null, causing a panic.

Not sure yet how exactly we allowed through a call when the
tid state does not have at least HT_ADDBA_REQUESTED_MSK set,
that will require some further review as it is not quite
obvious.

For more information see the bug report:

http://bugzilla.kernel.org/show_bug.cgi?id=13922

This fixes this oops:

BUG: unable to handle kernel NULL pointer dereference at 00000030
IP: [<f8806c70>] ieee80211_agg_splice_packets+0x40/0xc0 [mac80211]
*pdpt = 0000000002d1e001 *pde = 0000000000000000
Thread overran stack, or stack corrupted
Oops: 0000 [#1] SMP
last sysfs file: /sys/module/aes_generic/initstate
Modules linked in: <bleh>

Pid: 0, comm: swapper Not tainted (2.6.31-rc5-wl #2) Dell DV051
EIP: 0060:[<f8806c70>] EFLAGS: 00010292 CPU: 0
EIP is at ieee80211_agg_splice_packets+0x40/0xc0 [mac80211]
EAX: 00000030 EBX: 0000004c ECX: 00000003 EDX: 00000000
ESI: c1c98000 EDI: f745a1c0 EBP: c076be58 ESP: c076be38
 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
Process swapper (pid: 0, ti=c076a000 task=c0709160 task.ti=c076a000)
Stack: <bleh2>
Call Trace:
 [<f8806edb>] ? ieee80211_stop_tx_ba_cb+0xab/0x150 [mac80211]
 [<f8802f1e>] ? ieee80211_tasklet_handler+0xce/0x110 [mac80211]
 [<c04862ff>] ? net_rx_action+0xef/0x1d0
 [<c0149378>] ? tasklet_action+0x58/0xc0
 [<c014a0f2>] ? __do_softirq+0xc2/0x190
 [<c018eb48>] ? handle_IRQ_event+0x58/0x140
 [<c01205fe>] ? ack_apic_level+0x7e/0x270
 [<c014a1fd>] ? do_softirq+0x3d/0x40
 [<c014a345>] ? irq_exit+0x65/0x90
 [<c010a6af>] ? do_IRQ+0x4f/0xc0
 [<c014a35d>] ? irq_exit+0x7d/0x90
 [<c011d547>] ? smp_apic_timer_interrupt+0x57/0x90
 [<c01094a9>] ? common_interrupt+0x29/0x30
 [<c010fd9e>] ? mwait_idle+0xbe/0x100
 [<c0107e42>] ? cpu_idle+0x52/0x90
 [<c054b1a5>] ? rest_init+0x55/0x60
 [<c077492d>] ? start_kernel+0x315/0x37d
 [<c07743ce>] ? unknown_bootoption+0x0/0x1f9
 [<c0774099>] ? i386_start_kernel+0x79/0x81
Code: <bleh3>
EIP: [<f8806c70>] ieee80211_agg_splice_packets+0x40/0xc0 [mac80211] SS:ESP 0068:c076be38
CR2: 0000000000000030

Cc: stable@kernel.org
Testedy-by: NJack Lau <jackelectronics@hotmail.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When an interface is configured in the AP mode, the mac80211
implementation doesn't inform the driver to receive PS Poll frames.
It leads to inability to communicate with power-saving stations
reliably.
The FIF_CONTROL flag isn't passed by mac80211 to
ieee80211_ops.configure_filter when an interface is in the AP mode.
And it's ok, because we don't want to receive ACK frames and other
control ones, but only PS Poll ones.

This patch introduces the FIF_PSPOLL filter flag in addition to
FIF_CONTROL, which means for the driver "pass PS Poll frames".

This flag is passed to the driver:
A) When an interface is configured in the AP mode.
B) In all cases, when the FIF_CONTROL flag was passed earlier (in
addition to it).
Signed-off-by: NIgor Perminov <igor.perminov@inbox.ru>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Do a probe request every 30 seconds, and wait for probe response,
half a second This should lower the traffic that card sends, thus save
power Wainting longer for response makes probe more robust against
'slow' access points
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Tested-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Retry 5 times  (chosen arbitary ), before assuming
that station is out of range.

Fixes frequent disassociations while connected to weak,
and sometimes even strong access points.
Signed-off-by: NMaxim Levitky <maximlevitsky@gmail.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since the bss is always set now once we are connected, if the
bss has its own information element we refer to it and pass that
instead of relying on mac80211's parsing.

Now all cfg80211 drivers get country IE support, automatically and
we reduce the call overhead that we had on mac80211 which called this
upon every beacon and instead now call this only upon a successfull
connection by a STA on cfg80211.
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some of the recent MLME rework I did broke powersave
because the ps_sdata isn't assigned at the right time,
and the work item wasn't removed from the list before
calling ieee80211_recalc_ps(). To be more specific,
this broke the case where you'd enabled PS before
associating, either automatically or with iwconfig.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>