Add support to disconnect the pull-up resistor on CD/DAT[3] (pin 1)
of the card. This may be desired on certain setups of boards,
controllers and embedded sdio devices which do not need the card's
pull-up. As a result, card detection is disabled and power is saved.

[akpm@linux-foundation.org: simplify sdio_disable_cd() a bit]
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Acked-by: NMatt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Philip Langdale <philipl@overt.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is needed for 1.8V embedded SDIO devices and supporting host controllers
(e.g. TI 127x and ZOOM2 boards)
Signed-off-by: NOhad Ben-Cohen <ohad@bencohen.org>
Acked-by: NMatt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Philip Langdale <philipl@overt.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Suppressing uevents turned out to be a bad idea as it screws up the
order of events, making user space very confused. Change the system to
use sysfs groups instead.

This is a regression that, for some odd reason, has gone unnoticed for
some time. It confuses hal so that the block devices (which have the
mmc device as a parent) are not registered. End result being that
desktop magic when cards are inserted won't work.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Teach the MMC/SD/SDIO core about using SPI mode.

 - Use mmc_host_is_spi() so enumeration works through SPI signaling
   and protocols, not just the native versions.

 - Provide the SPI response type flags with each request issued,
   including requests from the new lock/unlock code.

 - Understand that cmd->resp[0] and mmc_get_status() results for SPI
   return different values than for "native" MMC/SD protocol; this
   affects resetting, checking card lock status, and some others.

 - Understand that some commands act a bit differently ... notably:
     * OP_COND command doesn't return the OCR
     * APP_CMD status doesn't have an R1_APP_CMD analogue

Those changes required some new and updated primitives:

 - Provide utilities to access two SPI-only requests, and one
   request that wasn't previously needed:
     * mmc_spi_read_ocr() ... SPI only
     * mmc_spi_set_crc() ... SPI only (override by module parm)
     * mmc_send_cid() ... for use without broadcast mode

 - Updated internal routines:
     * Previous mmc_send_csd() modified into mmc_send_cxd_native();
       it uses native "R2" responses, which include 16 bytes of data.
     * Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data()
       helper for command-and-data access
     * Bugfix to that mmc_send_cxd_data() code:  dma-to-stack is
       unsafe/nonportable, so kmalloc a bounce buffer instead.

 - Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper

 - Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use
   those helper routines based on whether they're native or SPI

The newest categories of cards supported by the MMC stack aren't expected
to work yet with SPI:  MMC or SD cards with over 4GB data, and SDIO.
All those cards support SPI mode, so eventually they should work too.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Replace all cases of BUG_ON with WARN_ON where there is a chance
(with varying degrees of slim) that the kernel can continue without
incidence.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Signed-off-by: NDavid Vrabel <david.vrabel@csr.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Enable 4-bit data bus mode, according to host and card
capabilities.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Change clock speed to the highest supported by the card.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Add a more clean separation between global, common CIS information
and the function specific one as we need the common information in
places where no specific function is specified.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Signed-off-by: NNicolas Pitre <npitre@mvista.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Add the sdio bus type and basic device handling.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Really basic init sequence for SDIO cards.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>