Free up mbox_log allocated for PF0 to PF3.

Fixes: 7829451c ("cxgb4: Add control net_device for configuring PCIe VF")
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to push the chain index down to the drivers, so they have the
information to which chain the rule belongs. For now, no driver supports
multichain offload, so only chain 0 is supported. This is needed to
prevent chain squashes during offload for now. Later this will be used
to implement multichain offload.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

the adapter consumes two tids for every ipv6 offload
connection be it active or passive, calculate tid usage
count accordingly.

Also change the signatures of relevant functions to get
the address family.
Signed-off-by: NRizwan Ansari <rizwana@chelsio.com>
Signed-off-by: NVarun Prakash <varun@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement ndo_set_vf_rate() for mgmt interface to support rate-limiting
of VF traffic using 'ip' command.

Based on the original work of Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Take uld mutex to avoid race between cxgb_up() and
cxgb4_register_uld() to enable napi for the same uld
queue.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GRO is not supported by Chelsio HW when rx_csum is disabled.
Update the netdev features flag when rx_csum is modified.
Signed-off-by: NArjun Vynipadath <arjun@chelsio.com>
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mark carrier off before registering netdev to ensure that vlan device
picks up the correct state of the carrier
Signed-off-by: NSurendra Mobiya <surendra@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During PCI error recovery process, specifically on eeh_err_detected()
we might have a NULL netdev struct, hence a direct dereference will
lead to a kernel oops. This was observed with latest upstream kernel
(v4.12-rc2) on Chelsio adapter T422-CR in PowerPC machines.

This patch checks for NULL pointer and avoids the crash, both in
eeh_err_detected() and eeh_resume(). Also, we avoid to trigger
a fatal error or to try disabling interrupts on FW during PCI
error recovery, because: (a) driver might not be able to accurately
access PCI regions in this case, and (b) trigger a fatal error
_during_ the recovery steps is a mistake that could prevent the
recovery path to complete successfully.
Reported-by: NHarsha Thyagaraja <hathyaga@in.ibm.com>
Signed-off-by: NGuilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

issue get port information command to firmware to retrieve port
information and update if it is different from what was last
recorded and also add indication for supported link modes for
firmware port types FW_PORT_TYPE_SFP28, FW_PORT_TYPE_KR_SFP28,
FW_PORT_TYPE_CR4_QSFP.

Based on the original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When is_kdump_kernel() is true, reduce memory footprint of
cxgb4 by using a single "Queue Set".
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are many code paths opencoding kvmalloc.  Let's use the helper
instead.  The main difference to kvmalloc is that those users are
usually not considering all the aspects of the memory allocator.  E.g.
allocation requests <= 32kB (with 4kB pages) are basically never failing
and invoke OOM killer to satisfy the allocation.  This sounds too
disruptive for something that has a reasonable fallback - the vmalloc.
On the other hand those requests might fallback to vmalloc even when the
memory allocator would succeed after several more reclaim/compaction
attempts previously.  There is no guarantee something like that happens
though.

This patch converts many of those places to kv[mz]alloc* helpers because
they are more conservative.

Link: http://lkml.kernel.org/r/20170306103327.2766-2-mhocko@kernel.orgSigned-off-by: NMichal Hocko <mhocko@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> # Xen bits
Acked-by: NKees Cook <keescook@chromium.org>
Acked-by: NVlastimil Babka <vbabka@suse.cz>
Acked-by: Andreas Dilger <andreas.dilger@intel.com> # Lustre
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com> # KVM/s390
Acked-by: Dan Williams <dan.j.williams@intel.com> # nvdim
Acked-by: David Sterba <dsterba@suse.com> # btrfs
Acked-by: Ilya Dryomov <idryomov@gmail.com> # Ceph
Acked-by: Tariq Toukan <tariqt@mellanox.com> # mlx4
Acked-by: Leon Romanovsky <leonro@mellanox.com> # mlx5
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Colin Cross <ccross@android.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Santosh Raspatur <santosh@chelsio.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Yishai Hadas <yishaih@mellanox.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: "Yan, Zheng" <zyan@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The patch fixes a critical issue to map txqid with flows on the hardware appropriately,
if tx queues created are more than flows configured then  txqid shall map within
the range of hardware flows configured. This ensure that un-mapped txqid does not remain un-handled.
The patch also segregated the rxqid and txqid for clarity.
Signed-off-by: NAtul Gupta <atul.gupta@chelsio.com>
Reviewed-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Save the filter tid while creating the server filter, which is used
later to retrieve the corresponding filter instance while handling
the filter reply.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make max number of supported tc u32 links equal to max number of filters
supported by hardware.
Signed-off-by: NArjun V <arjun@chelsio.com>
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Count buffer group drops or truncates as rx drops rather than
rx errors in netdev stats.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NArjun V <arjun@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes use of is_vlan_dev() function instead of flag
comparison which is exactly done by is_vlan_dev() helper function.
Signed-off-by: NParav Pandit <parav@mellanox.com>
Reviewed-by: NDaniel Jurgens <danielj@mellanox.com>
Acked-by: NStephen Hemminger <stephen@networkplumber.org>
Acked-by: NJon Maxwell <jmaxwell37@gmail.com>
Acked-by: NJohannes Thumshirn <jth@kernel.org>
Acked-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.

Not only we remove lot of code, we also remove one spin_lock()
from driver fast path.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The two new variables are only used inside of an #ifdef and cause
harmless warnings when that is disabled:

drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c: In function 'init_one':
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:4646:9: error: unused variable 'port_vec' [-Werror=unused-variable]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:4646:6: error: unused variable 'v' [-Werror=unused-variable]

This adds another #ifdef around the declarations.

Fixes: 96fe11f2 ("cxgb4: Implement ndo_get_phys_port_id for mgmt dev")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Perform an emergency shutdown of the adapter and stop it from
continuing any further communication on the ports or DMA to the
host. This is typically used when the adapter and/or firmware
have crashed and we want to prevent any further accidental
communication with the rest of the world. This will also force
the port Link Status to go down -- if register writes work --
which should help our peers figure out that we're down.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initialize mbox lock and list for mgmt dev to avoid NULL pointer
dereference when cxgb_set_vf_mac is called.

And also allocate memory for private data while allocating mgmt
netdev.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.

Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to report 25G and 100G links, which was missed
as part of commit "eb97ad99".
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The issue comes when there are multiple threads attempting to use
the mailbox facility at the same time.
When DCB operations and interface up/down is run in a loop for every
0.1 sec, we observed mailbox collisions. And out of the two commands
one would fail with the present code, since we don't queue the second
command.

To overcome the above issue, added a queue to access the mailbox.
Whenever a mailbox command is issued add it to the queue. If its at
the head issue the mailbox command, else wait for the existing command
to complete. Usually command takes less than a milli-second to
complete.

Also timeout from the loop, if the command under execution takes
long time to run.

In reality, the number of mailbox access collisions is going to be
very rare since no one runs such abusive script.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This was entirely automated, using the script by Al:

  PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
  sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
        $(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)

to do the replacement at the end of the merge window.
Requested-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Added missing dev_port assignment in cxgb4vf driver.
Also made dev_port assignment of cxgb4 in sync with cxgb4vf driver.
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NArjun V <arjun@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove deprecated module parameters num_vf, dflt_msg_enable and
force_init.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocate resources dynamically for Upper layer driver's (ULD) like
cxgbit, iw_cxgb4, cxgb4i and chcr. The resources allocated include Tx
queues which are allocated when ULD register with cxgb4 driver and freed
while un-registering. The Tx queues which are shared by ULD shall be
allocated by first registering driver and un-allocated by last
unregistering driver.
Signed-off-by: NAtul Gupta <atul.gupta@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Somehow, I missed a healthy number of ethernet drivers in the last pass.
Most of these drivers either were in need of an updated max_mtu to make
jumbo frames possible to enable again. In a few cases, also setting a
different min_mtu to match previous lower bounds. There are also a few
drivers that had no upper bounds checking, so they're getting a brand new
ETH_MAX_MTU that is identical to IP_MAX_MTU, but accessible by includes
all ethernet and ethernet-like drivers all have already.

acenic:
- min_mtu = 0, max_mtu = 9000

amazon/ena:
- min_mtu = 128, max_mtu = adapter->max_mtu

amd/xgbe:
- min_mtu = 0, max_mtu = 9000

sb1250:
- min_mtu = 0, max_mtu = 1518

cxgb3:
- min_mtu = 81, max_mtu = 65535

cxgb4:
- min_mtu = 81, max_mtu = 9600

cxgb4vf:
- min_mtu = 81, max_mtu = 65535

benet:
- min_mtu = 256, max_mtu = 9000

ibmveth:
- min_mtu = 68, max_mtu = 65535

ibmvnic:
- min_mtu = adapter->min_mtu, max_mtu = adapter->max_mtu
- remove now redundant ibmvnic_change_mtu

jme:
- min_mtu = 1280, max_mtu = 9202

mv643xx_eth:
- min_mtu = 64, max_mtu = 9500

mlxsw:
- min_mtu = 0, max_mtu = 65535
- Basically bypassing the core checks, and instead relying on dynamic
  checks in the respective switch drivers' ndo_change_mtu functions

ns83820:
- min_mtu = 0
- remove redundant ns83820_change_mtu, only checked for mtu > 1500

netxen:
- min_mtu = 0, max_mtu = 8000 (P2), max_mtu = 9600 (P3)

qlge:
- min_mtu = 1500, max_mtu = 9000
- driver only supports setting mtu to 1500 or 9000, so the core check only
  rules out < 1500 and > 9000, qlge_change_mtu still needs to check that
  the value is 1500 or 9000

qualcomm/emac:
- min_mtu = 46, max_mtu = 9194

xilinx_axienet:
- min_mtu = 64, max_mtu = 9000

Fixes: 61e84623 ("net: centralize net_device min/max MTU checking")
CC: netdev@vger.kernel.org
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Netanel Belgazal <netanel@annapurnalabs.com>
CC: Tom Lendacky <thomas.lendacky@amd.com>
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Hariprasad S <hariprasad@chelsio.com>
CC: Sathya Perla <sathya.perla@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
CC: Somnath Kotur <somnath.kotur@broadcom.com>
CC: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
CC: John Allen <jallen@linux.vnet.ibm.com>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
CC: Jiri Pirko <jiri@mellanox.com>
CC: Ido Schimmel <idosch@mellanox.com>
CC: Manish Chopra <manish.chopra@qlogic.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Rajesh Borundia <rajesh.borundia@qlogic.com>
CC: Timur Tabi <timur@codeaurora.org>
CC: Anirudha Sarangi <anirudh@xilinx.com>
CC: John Linn <John.Linn@xilinx.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not let number of offload queue sets to go more than
MAX_OFLD_QSETS, which would otherwise crash the driver
on machines with cores more than MAX_OFLD_QSETS.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Query firmware for the FW_PARAMS_PARAM_DEV_RI_FR_NSMR_TPTE_WR parameter.
If it exists and is 1, then advertise support for FR_NSMR_TPTE_WR to
the ULDs.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

A recent cleanup marked cxgb4_dcb_enabled as 'static', which is correct, but this ignored
how the symbol is also exported. In addition, the export can be compiled out when modules
are disabled, causing a harmless compiler warning in configurations for which it is not
used at all:

drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:282:12: error: 'cxgb4_dcb_enabled' defined but not used [-Werror=unused-function]

This removes the export and moves the function into the correct #ifdef so we only build
it when there are users.

Fixes: 50935857 ("cxgb4: mark symbols static where possible")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We get 1 warning when building kernel with W=1:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:2715:5: warning: no previous prototype for 'cxgb_setup_tc' [-Wmissing-prototypes]

In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.
Signed-off-by: NBaoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We get 10 warnings when building kernel with W=1:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:304:5: warning: no previous prototype for 'cxgb4_dcb_enabled' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:194:5: warning: no previous prototype for 'setup_sge_queues_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:241:6: warning: no previous prototype for 'free_sge_queues_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:268:5: warning: no previous prototype for 'cfg_queues_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:344:6: warning: no previous prototype for 'free_queues_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:353:5: warning: no previous prototype for 'request_msix_queue_irqs_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:379:6: warning: no previous prototype for 'free_msix_queue_irqs_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:393:6: warning: no previous prototype for 'name_msix_vecs_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:433:6: warning: no previous prototype for 'enable_rx_uld' [-Wmissing-prototypes]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:442:6: warning: no previous prototype for 'quiesce_rx_uld' [-Wmissing-prototypes]

In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: NBaoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for offloading u32 filter onto hardware.  Links are stored
in a jump table to perform necessary jumps to match TCP/UDP header.
When inserting rules in the linked bucket, the TCP/UDP match fields
in the corresponding entry of the jump table are appended to the filter
rule before insertion.  If a link is deleted, then all corresponding
filters associated with the link are also deleted.  Also enable
hardware tc offload as a supported feature.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable filters for non-offload configuration and add common api support
for setting and deleting filters in LE-TCAM region of the hardware.

IPv4 filters occupy one slot.  IPv6 filters occupy 4 slots and must
be on a 4-slot boundary.  IPv4 filters can not occupy a slot belonging
to IPv6 and the vice-versa is also true.

Filters are set and deleted asynchronously.  Use completion to wait
for reply from firmware in order to allow for synchronization if needed.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move common filter code to separate files.  Also fix the following
checkpatch checks.

CHECK: Comparison to NULL could be written "!f->l2t"
+               if (f->l2t == NULL) {

CHECK: spaces preferred around that '/' (ctx:VxV)
+       fwr->len16_pkd = htonl(FW_WR_LEN16_V(sizeof(*fwr)/16));
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We were missing check for 25G and 100G while checking port speed,
which lead to less number of queues getting allocated for 25G & 100G
adapters and leading to low throughput. Adding the missing check for
both NIC and vNIC driver.

Also fixes port advertisement for 25G and 100G in ethtool output.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocate resources dynamically to cxgb4's Upper layer driver's(ULD) like
cxgbit, iw_cxgb4 and cxgb4i. Allocate resources when they register with
cxgb4 driver and free them while unregistering. All the queues and the
interrupts for them will be allocated during ULD probe only and freed
during remove.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds support for ndo_get_vf_config, also fill the default mac address
that will be provided to the VF by firmware, in case user doesn't
provide one. So user can get the default MAC address address also
through ndo_get_vf_config.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>