Eliminate two warnings:

kernel/power/pm.c:205: warning: 'pm_register' is deprecated (declared at kernel/power/pm.c:64)
kernel/power/pm.c:206: warning: 'pm_send_all' is deprecated (declared at kernel/power/pm.c:180)

by updating defconfig files to contain a sensible PM_LEGACY default.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Reimplement execvp for our purposes - after we call fork() it is fundamentally
unsafe to use the kernel allocator - current is not valid there.  So we simply
pass to our modified execvp() a preallocated buffer.  This fixes a real bug
and works very well in testing (I've seen indirectly warning messages from the
forked thread - they went on the pipe connected to its stdout and where read
as a number by UML, when calling read_output().  I verified the obtained
number corresponded to "BUG:").

The added use of __cant_sleep() is not a new bug since __cant_sleep() is
already used in the same function - passing an atomicity parameter would be
better but it would require huge change, stating that this function must not
be called in atomic context and can sleep is a better idea (will make sure of
this gradually).
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: NJeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Removing flush_icache_page a while ago broke SB1 which was using an empty
flush_data_cache_page function.  This glues things well enough so a more
efficient but also more intrusive solution can be found later.
Signed-Off-By: NThiemo Seufer <ths@networkno.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

/*
 * Note: Drivers should NOT use this function directly, as it will break
 * platforms with CONFIG_DMABOUNCE.
 * Use the driver DMA support - see dma-mapping.h (dma_sync_*)
 */
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

mpc832x, as in mpc8360, needs to explicitly find and create the
platform device for ucc_geth in 2.6.19.  This code will likely be
readapted to Benh's new of_ methods for 2.6.20.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This reverts commit 7a69af63.

As advised by David Brownell:

http://marc.theaimsgroup.com/?l=linux-kernel&m=116387226902131&w=2Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This reverts commit a8ed4f7e.

As advised by David Brownell:

http://marc.theaimsgroup.com/?l=linux-kernel&m=116387226902131&w=2Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

o Explicitly align data segment to PAGE_SIZE boundary otherwise depending on
  config options and tool chain it might be placed on a non PAGE_SIZE aligned
  boundary and vmlinux loaders like kexec fail when they encounter a
  PT_LOAD type segment which is not aligned to PAGE_SIZE boundary.
Signed-off-by: NVivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: NAndi Kleen <ak@suse.de>

Switch to using irq_handler_t for interrupt function handler pointers.

Change name of m68knommu's irq_hanlder_t data structure so it doesn't
clash with the common type (include/linux/interrupt.h).
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This is to fix compile error of x86-64 memory hotplug without any NUMA
option.

  CC      arch/x86_64/mm/init.o
arch/x86_64/mm/init.c:501: error: redefinition of 'memory_add_physaddr_to_nid'
include/linux/memory_hotplug.h:71: error: previous definition of 'memory_add_phys
addr_to_nid' was here
arch/x86_64/mm/init.c:509: error: redefinition of 'memory_add_physaddr_to_nid'
arch/x86_64/mm/init.c:501: error: previous definition of 'memory_add_physaddr_to_
nid' was here

I confirmed compile completion with !NUMA, (NUMA & !ACPI_NUMA),
or (NUMA & ACPI_NUMA).
Signed-off-by: NYasunori Goto <y-goto@jp.fujitsu.com>
Acked-by: NAndi Kleen <ak@suse.de>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Remove two warnings:
drivers/serial/8250_early.c:136: warning: unused variable 'mapsize'
include/linux/io.h:47: warning: passing argument 1 of '__readb' discards qualifiers from pointer target type
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

ARM doesn't source drivers/Kconfig like most architectures do, so the
newly added drivers/ata is currently not made available on ARM.  SATA
is used on some ARM machines, like the Thecus N2100, so we need to
source drivers/ata/Kconfig.
Signed-off-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

When showing the stack backtrace, make sure that we never accept not
only an unchanging frame pointer, but also a frame pointer that moves
back down the stack frame.  It must always grow up (toward older stack
frames).

I doubt this has triggered, but a subtly corrupt stack with extremely
unlucky contents could cause us to loop forever on a bogus endless frame
pointer chain.

This review was triggered by much worse problems happening in some of
the other stack unwinding code.
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The scheduler on Andreas Friedrich's hyperthreading system stopped
working properly: the scheduler would never move tasks to another CPU!
The lask known working kernel was 2.6.8.

After a couple of attempts to corner the bug, the following smoking gun
was found:

  BIOS reported wrong ACPI idfor the processor
  CPU#1: set_cpus_allowed(), swapper:1, 3 -> 2
   [<c0103bbe>] show_trace_log_lvl+0x34/0x4a
   [<c0103ceb>] show_trace+0x2c/0x2e
   [<c01045f8>] dump_stack+0x2b/0x2d
   [<c0116a77>] set_cpus_allowed+0x52/0xec
   [<c0101d86>] cpu_idle_wait+0x2e/0x100
   [<c0259c57>] acpi_processor_power_exit+0x45/0x58
   [<c0259752>] acpi_processor_remove+0x46/0xea
   [<c025c6fb>] acpi_start_single_object+0x47/0x54
   [<c025cee5>] acpi_bus_register_driver+0xa4/0xd3
   [<c04ab2d7>] acpi_processor_init+0x57/0x77
   [<c01004d7>] init+0x146/0x2fd
   [<c0103a87>] kernel_thread_helper+0x7/0x10

a quick look at cpu_idle_wait() shows how broken that code is
on i386: it changes the init task's affinity map but never
restores it ...

and because all userspace tasks get forked by init, they all
inherited that single-CPU affinity mask. x86_64 cloned this
bug too.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: Andreas Friedrich <andreas.friedrich@fujitsu-siemens.com>
Cc: Wolfgang Erig <Wolfgang.Erig@fujitsu-siemens.com>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

the new dwarf2 unwinder crashes while trying to dump the stack:

  Leftover inexact backtrace:

  Unable to handle kernel paging request at ffffffff82800000 RIP:
   [<ffffffff8026cf26>] dump_trace+0x35b/0x3d2
  PGD 203027 PUD 205027 PMD 0
  Oops: 0000 [2] PREEMPT SMP
  CPU 0
  Modules linked in:
  Pid: 30, comm: khelper Not tainted 2.6.19-rc6-rt1 #11
  RIP: 0010:[<ffffffff8026cf26>]  [<ffffffff8026cf26>] dump_trace+0x35b/0x3d2
  RSP: 0000:ffff81003fb9d848  EFLAGS: 00010006
  RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
  RDX: 0000000000000000 RSI: ffffffff805b3520 RDI: 0000000000000000
  RBP: ffffffff827ffff9 R08: ffffffff80aad000 R09: 0000000000000005
  R10: ffffffff80aae000 R11: ffffffff8037961b R12: ffff81003fb9d858
  R13: 0000000000000000 R14: ffffffff80598460 R15: ffffffff80ab1fc0
  FS:  0000000000000000(0000) GS:ffffffff806c4200(0000) knlGS:0000000000000000
  CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
  CR2: ffffffff82800000 CR3: 0000000000201000 CR4: 00000000000006e0

this crash happened because it did not sanitize the dwarf2 data it
got, and got an unaligned stack pointer - which happily walked past
the process stack (and eventually reached the end of kernel memory
and pagefaulted there) due to this naive iteration condition:

        HANDLE_STACK (((long) stack & (THREAD_SIZE-1)) != 0);

note that i386 is alot more conservative when it comes to trusting
stack pointers:

  static inline int valid_stack_ptr(struct thread_info *tinfo, void *p)
  {
         return  p > (void *)tinfo &&
                 p < (void *)tinfo + THREAD_SIZE - 3;
  }

but the x86_64 code did not take this bit of i386 code.

The fix is to align the stack pointer.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

on x86_64, the CONFIG_CC_STACKPROTECTOR build fails if used in a
distcc setup that has "CC" defined to "distcc gcc":

 gcc: gcc: linker input file unused because linking not done
 gcc: gcc: linker input file unused because linking not done
 gcc: gcc: linker input file unused because linking not done

this is because the gcc-x86_64-has-stack-protector.sh script
has a 2-parameters assumption. Fix this by passing $(CC) as
a single parameter.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Please-Use-Me-More: make randconfig
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Broken by earlier patch by me.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The HP_SIMSCSI driver can't be built as a module (unhealthy dependencies on
things that shouldn't really be exported).
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Use generic_handle_irq() to handle mixed-type irq handling.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NTony Luck <tony.luck@intel.com>

convert irq chip typename -> name.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NTony Luck <tony.luck@intel.com>

`typename' is going away and is usually uninitialised anwyay.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NTony Luck <tony.luck@intel.com>

When called to do a transfer that has a start offset within the cache
line which is uneven between source and destination and a length which
terminates the source of the copy exactly on a cache line, one extra
line gets copied into a temporary buffer.  This is normally not an issue
since the buffer is a kernel buffer and only the requested information
gets copied into the user buffer.

The problem arises when the source ends at the very last physical page
of memory.  That last cache line does not exist and results in the SHUB
chip raising an MCA.
Signed-off-by: NRobin Holt <holt@sgi.com>
Signed-off-by: NDean Nelson <dcn@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Komuro reports that ISA interrupts do not work after a disable_irq(),
causing some PCMCIA drivers to not work, with messages like

	eth0: Asix AX88190: io 0x300, irq 3, hw_addr xx:xx:xx:xx:xx:xx
	eth0: found link beat
	eth0: autonegotiation complete: 100baseT-FD selected
	eth0: interrupt(s) dropped!
	eth0: interrupt(s) dropped!
	eth0: interrupt(s) dropped!
	...

Linus Torvalds <torvalds@osdl.org> said:

  "Now, edge-triggered interrupts are a _lot_ harder to mask, because the
   Intel APIC is an unbelievable piece of sh*t, and has the edge-detect logic
   _before_ the mask logic, so if a edge happens _while_ the device is
   masked, you'll never ever see the edge ever again (unmasking will not
   cause a new edge, so you simply lost the interrupt).

   So when you "mask" an edge-triggered IRQ, you can't really mask it at all,
   because if you did that, you'd lose it forever if the IRQ comes in while
   you masked it. Instead, we're supposed to leave it active, and set a flag,
   and IF the IRQ comes in, we just remember it, and mask it at that point
   instead, and then on unmasking, we have to replay it by sending a
   self-IPI."

This trivial patch solves the problem.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@redhat.com>
Acked-by: NKomuro <komurojun-mbn@nifty.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

(David:)

If hugetlbfs_file_mmap() returns a failure to do_mmap_pgoff() - for example,
because the given file offset is not hugepage aligned - then do_mmap_pgoff
will go to the unmap_and_free_vma backout path.

But at this stage the vma hasn't been marked as hugepage, and the backout path
will call unmap_region() on it.  That will eventually call down to the
non-hugepage version of unmap_page_range().  On ppc64, at least, that will
cause serious problems if there are any existing hugepage pagetable entries in
the vicinity - for example if there are any other hugepage mappings under the
same PUD.  unmap_page_range() will trigger a bad_pud() on the hugepage pud
entries.  I suspect this will also cause bad problems on ia64, though I don't
have a machine to test it on.

(Hugh:)

prepare_hugepage_range() should check file offset alignment when it checks
virtual address and length, to stop MAP_FIXED with a bad huge offset from
unmapping before it fails further down.  PowerPC should apply the same
prepare_hugepage_range alignment checks as ia64 and all the others do.

Then none of the alignment checks in hugetlbfs_file_mmap are required (nor
is the check for too small a mapping); but even so, move up setting of
VM_HUGETLB and add a comment to warn of what David Gibson discovered - if
hugetlbfs_file_mmap fails before setting it, do_mmap_pgoff's unmap_region
when unwinding from error will go the non-huge way, which may cause bad
behaviour on architectures (powerpc and ia64) which segregate their huge
mappings into a separate region of the address space.
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: NAdam Litke <agl@us.ibm.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix interrupt routing for via 586 bridges.  pirq can be 5 which needs to be
mapped to INTD.  But currently the access functions can handle only pirq
1-4.  this is similar to the other via chipsets where pirq 4 and 5 are both
mapped to INTD.  Fixes bugzilla #7490

Cc: Daniel Paschka <monkey20181@gmx.net>
Cc: Adrian Bunk <bunk@susta.de>
Signed-off-by: NDaniel Ritz <daniel.ritz@gmx.ch>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When another interrupt happens in exit_idle the exit idle notifier
could be called an incorrect number of times.

Add a test_and_clear_bit_pda and use it handle the bit
atomically against interrupts to avoid this.

Pointed out by Stephane Eranian
Signed-off-by: NAndi Kleen <ak@suse.de>

The vgetcpu per CPU initialization previously relied on CPU hotplug
events for all CPUs to initialize the per CPU state. That only
worked only on kernels with CONFIG_HOTPLUG_CPU enabled.  On the
others some CPUs didn't get their state initialized properly
and vgetcpu wouldn't work.

Change the initialization sequence to instead run in a normal
initcall (which runs after the normal CPU bootup) and initialize
all running CPUs there. Later hotplug CPUs are still handled
with an hotplug notifier.

This actually simplifies the code somewhat.
Signed-off-by: NAndi Kleen <ak@suse.de>

Timer overrides are normally disabled on Nvidia board because
they are commonly wrong, except on new ones with HPET support.
Unfortunately there are quite some Asus boards around that
don't have HPET, but need a timer override.

We don't know yet how to handle this transparently,
but at least add a command line option to force the timer override
and let them boot.

Cc: len.brown@intel.com
Signed-off-by: NAndi Kleen <ak@suse.de>

x86_64: setup saved_max_pfn correctly

2.6.19-rc4 has broken CONFIG_CRASH_DUMP support on x86_64. It is impossible
to read out the kernel contents from /proc/vmcore because saved_max_pfn is set
to zero instead of the max_pfn value before the user map is setup.

This happens because saved_max_pfn is initialized at parse_early_param() time,
and at this time no active regions have been registered. save_max_pfn is setup
from e820_end_of_ram(), more exact find_max_pfn_with_active_regions() which
returns 0 because no regions exist.

This patch fixes this by registering before and removing after the call
to e820_end_of_ram().
Signed-off-by: NMagnus Damm <magnus@valinux.co.jp>
Signed-off-by: NAndi Kleen <ak@suse.de>

This can happen on kexec kernels with some configurations, in particularly
on Unisys ES7000 systems.

Analysis by Amul Shah

Cc: Amul Shah <amul.shah@unisys.com>
Signed-off-by: NAndi Kleen <ak@suse.de>

Stephen Tweedie, Herbert Xu, and myself have been struggling with a very
nasty bug in Xen.  But it also pointed out a small bug in the x86_64
kernel boot setup.

The GDT limit being setup by the initial bzImage code when entering into
protected mode is way too big.  The comment by the code states that the
size of the GDT is 2048, but the actual size being set up is much bigger
(32768). This happens simply because of one extra '0'.

Instead of setting up a 0x800 size, 0x8000 is set up.  On bare metal this
is fine because the CPU wont load any segments unless  they are
explicitly used.  But unfortunately, this breaks Xen on vmx FV, since it
(for now) blindly loads all the segments into the VMCS if they are less
than the gdt limit. Since the real mode segments are around 0x3000, we are
getting junk into the VMCS and that later causes an exception.

Stephen Tweedie has written up a patch to fix the Xen side and will be
submitting that to those folks. But that doesn't excuse the GDT limit
being a magnitude too big.

AK: changed to compute true gdt size in assembler, fixed comment
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NAndi Kleen <ak@suse.de>

ptrace(PTRACE_[SG]ET_THREAD_AREA) calls from ia32 code
should be passed onto the x86_64 implementation.

The default case in sys32_ptrace used to call to sys_ptrace(), but is
now EINVAL.  This patch fixes a regression caused by that changed.
Signed-off-by: NMike McCormack <mike@codeweavers.com>
Signed-off-by: NAndi Kleen <ak@suse.de>

Fix partial page check in e820_register_active_regions to ensure
partial pages are
not being marked as active in the memory pool.
Signed-off-by: NAaron Durbin <adurbin@google.com>
Signed-off-by: NAndi Kleen <ak@suse.de>

This reverts 4c6e052a commit.

Following Linus' i386 change: revert resource reservation
for mmcfg config now. Will be revisited in .20 hopefully.

OP_MAX_COUNTER never referenced, and is a reminant of an earlier
oprofile implementation.  Remove it.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix MSPEC driver to build for non SN2 enabled configs as the driver should
work in cached and uncached modes (no fetchop) on these systems.  In
addition make MSPEC select IA64_UNCACHED_ALLOCATOR, which is required for
it and move it to arch/ia64/Kconfig to avoid warnings on non ia64
architectures running allmodconfig.  Once the Kconfig code is fixed, we can
move it back.
Signed-off-by: NJes Sorensen <jes@sgi.com>
Cc: Fernando Luis Vzquez Cao <fernando@oss.ntt.co.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Most ARM defconfigs don't actually need to have PM_LEGACY enabled.
Disable it for ATEB9200, Collie, IXP4xx, OMAP H2, S3C2410 and
Versatile.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The current cell processor support needs sparsemem, so set it as
the default memory model.
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Acked-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This fixes a typo in the "new style" code for mapping SPE resources,
which causes it to try to map the same resource 4 times.

It also adds some pr_debug's that are useful to track down issues with
the firmware when bringinh up new machines.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The enablement of 64k pages on pseries platforms exposed a bug in
the RTAS mechanism for updating firmware.  RTAS assumes 4k for flash
block and list sizes, and use of any other sizes results in a failure,
even though PAPR does not specify any such requirement.

This patch changes the rtas_flash module to force the use of 4k memory
block and list sizes when preparing and sending a firmware image to
RTAS.  The rtas_flash function now uses a slab cache of 4k blocks with
4k alignment, rather than get_zeroed_page(), to allocate the memory for
the flash blocks and lists.  The 4k alignment requirement is specified
in PAPR.
Signed-off-by: NJohn Rose <johnrose@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>