All of the ethtool code paths keep them in sync, but we need
to ensure they are sync'd at start of day. Matches the sft9001
driver.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Under certain conditions a PHY may backpressure Falcon B0
in such a way that flushes timeout. In normal circumstances
the phy poller would fix the PHY, and the flush could complete.

But efx_nic_flush_queues() is always called after efx_stop_all(),
so the poller has been stopped. Even if this weren't the case,
how long would we have to wait for the poller to fix this? And
several callers of efx_nic_flush_queues() are about to reset
the device anyway - so we don't need to do anything.

Work around this bug by scheduling a reset. Ensure that the
MAC is never rewired back into the datapath before the reset
runs (we already ignore all rx events anyway).
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

efx_pm_freeze() sets efx->state = STATE_FINI, which means
efx_reset_work() will abort any scheduled resets.

efx_pm_thaw() should reschedule efx_reset_work() again,
since a freeze/thaw will not have reset the hardware.

This bug was spotted by inspection - there is no real world example of
this happening.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most of its members are constant capabilities, not configuration.  The
new name is also consistent with the name of the pointer to it in
struct efx_nic and the names of structures used by other PHY drivers.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add AR8151 v2.0 Gigabit 1000 support
Change jumbo frame size to 6K
Update L0s/L1 rountine
        when link speed is 100M or 1G, set L1 link timer to 4 for l1d_2 and l2c_b2
        set L1 link timer to 7 for l2c_b, set L1 link timer to 0xF for others.
Update atl1c_suspend routine
	just refactory the function, add atl1c_phy_power_saving routine,
	when Wake On Lan enable, this func will be called to save power,
	it will reautoneg PHY to 10/100M speed depend on the link
	partners link capability.
Update atl1c_configure_des_ring
        do not use l2c_b default SRAM configuration.
Signed-off-by: NJie Yang <Jie.Yang@atheros.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As noticed by Julia Lawall, ipip6_tunnel_add_prl() incorrectly calls 
kzallloc(..., GFP_KERNEL) while a spinlock is held. She provided
a patch to use GFP_ATOMIC instead.

One possibility would be to convert this spinlock to a mutex, or
preallocate the thing before taking the lock.

After RCU conversion, it appears we dont need this lock, since 
caller already holds RTNL
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the IFF_ALLMULTI flag. Previously only the
IFF_PROMISC flag was supported.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Acked-By: NKrzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As mbox polling is done only in process context, it is better to
use schedule_timeout() instead of udelay().
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds cleanup code (things like unregistering irq,
disabling napi etc) to be_open() when an error occurs inside the
routine.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on a patch from http://simon.baatz.info/wol-support-for-an983b/

Tested to resume from suspend by magic packet.
Signed-off-by: NSteven Walter <stevenrwalter@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During the first suspend the chip would refuse to enter D3.  Subsequent
suspends worked okay.  During resume the chip is commanded into D0.
Doing so during initialization fixes the initial suspend.
Signed-off-by: NSteven Walter <stevenrwalter@gmail.com>
Signed-off-by: NGrant Grundler <grundler@parisc-linux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for using phylib and adds the required mdiobus driver
stubs. This allows for less code to be present in the driver and removes
the PHY status specific timer which is now handled by phylib directly.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

 - shuffle around functions to get rid of forward declarations
 - fix some CodingStyle and indentation issues
 - last but not least, get rid of the following CONFIG_MODULE=n warning:

	drivers/net/arcnet/capmode.c:52: warning: ‘capmode_proto’ defined but not used
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

readl() returns a 32-bit integer on all platforms.
There is no need to cast its return value.
Signed-off-by: NJunchang Wang <junchangwang@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ioread32() returns a 32-bit integer on all platforms.
There is no need to cast its return value.
Signed-off-by: NJunchang Wang <junchangwang@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of a fixed list of buffers, use the buffer pool correctly and
keep track of the outstanding buffer indexes using a fixed table.
Resolves reported HBUF_ERR's -- failures due to lack of receive buffers.
Signed-off-by: NChas Williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChas Williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChas Williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChas Williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Today, there are no means to know which port of a hardware device a netdev
interface uses. struct net_device conatins a field, dev_id, that can be used
for that. Use this field to save the port number in ConnectX that is being used
by the net device; port numbers are zero based.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use newly introduced netif_notify_peers() method to ensure a gratuitous ARP is
generated after a migration.
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: xen-devel@lists.xensource.com
Cc: stable@kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently such notifications are only generated when the device comes up or the
address changes. However one use case for these notifications is to enable
faster network recovery after a virtual machine migration (by causing switches
to relearn their MAC tables). A migration appears to the network stack as a
temporary loss of carrier and therefore does not trigger either of the current
conditions. Rather than adding carrier up as a trigger (which can cause issues
when interfaces a flapping) simply add an interface which the driver can use
to explicitly trigger the notification.
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: stable@kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This option causes a gratuitous ARP request, not a reply as the documentation
currently suggests.
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"phyinfo" can never be null here because we assigned it an address, so I
removed both the assert and the second check inside the if statement.  I
removed the "phyinfo->phy_layer != NULL" check as well because that was
asserted earlier.

Walter Harms suggested I move the "phyinfo->phy_ref_count++;" outside
the if condition for readability, so I have done that.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NSjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We already dereferenced uaddr towards the start of the function when we
checked that "uaddr->sa_family != AF_CAIF".  Both the check here and the
earlier check were added in bece7b23: "caif: Rewritten socket
implementation".  Before that patch, we assumed that we recieved a valid
pointer for uaddr, and based on that, I have removed this check.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NSjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use memdup_user when user data is immediately copied into the
allocated region.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@

-  to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+  to = memdup_user(from,size);
   if (
-      to==NULL
+      IS_ERR(to)
                 || ...) {
   <+... when != goto l1;
-  -ENOMEM
+  PTR_ERR(to)
   ...+>
   }
-  if (copy_from_user(to, from, size) != 0) {
-    <+... when != goto l2;
-    -EFAULT
-    ...+>
-  }
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use memdup_user when user data is immediately copied into the
allocated region.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@

-  to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+  to = memdup_user(from,size);
   if (
-      to==NULL
+      IS_ERR(to)
                 || ...) {
   <+... when != goto l1;
-  -ENOMEM
+  PTR_ERR(to)
   ...+>
   }
-  if (copy_from_user(to, from, size) != 0) {
-    <+... when != goto l2;
-    -EFAULT
-    ...+>
-  }
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use memdup_user when user data is immediately copied into the
allocated region.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@

-  to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+  to = memdup_user(from,size);
   if (
-      to==NULL
+      IS_ERR(to)
                 || ...) {
   <+... when != goto l1;
-  -ENOMEM
+  PTR_ERR(to)
   ...+>
   }
-  if (copy_from_user(to, from, size) != 0) {
-    <+... when != goto l2;
-    -EFAULT
-    ...+>
-  }
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use memdup_user when user data is immediately copied into the
allocated region.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@

-  to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+  to = memdup_user(from,size);
   if (
-      to==NULL
+      IS_ERR(to)
                 || ...) {
   <+... when != goto l1;
-  -ENOMEM
+  PTR_ERR(to)
   ...+>
   }
-  if (copy_from_user(to, from, size) != 0) {
-    <+... when != goto l2;
-    -EFAULT
-    ...+>
-  }
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use memdup_user when user data is immediately copied into the
allocated region.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@

-  to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+  to = memdup_user(from,size);
   if (
-      to==NULL
+      IS_ERR(to)
                 || ...) {
   <+... when != goto l1;
-  -ENOMEM
+  PTR_ERR(to)
   ...+>
   }
-  if (copy_from_user(to, from, size) != 0) {
-    <+... when != goto l2;
-    -EFAULT
-    ...+>
-  }
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use memdup_user when user data is immediately copied into the
allocated region.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@

-  to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+  to = memdup_user(from,size);
   if (
-      to==NULL
+      IS_ERR(to)
                 || ...) {
   <+... when != goto l1;
-  -ENOMEM
+  PTR_ERR(to)
   ...+>
   }
-  if (copy_from_user(to, from, size) != 0) {
-    <+... when != goto l2;
-    -EFAULT
-    ...+>
-  }
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use memdup_user when user data is immediately copied into the
allocated region.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@

-  to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+  to = memdup_user(from,size);
   if (
-      to==NULL
+      IS_ERR(to)
                 || ...) {
   <+... when != goto l1;
-  -ENOMEM
+  PTR_ERR(to)
   ...+>
   }
-  if (copy_from_user(to, from, size) != 0) {
-    <+... when != goto l2;
-    -EFAULT
-    ...+>
-  }
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tcp_md5_hash_skb_data() should handle skb->frag_list, and eventually
recurse.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netpoll does an interesting work in zap_completion_queue(), but this was
before we did skb orphaning before delivering packets to device.

It now makes sense to add a test in dev_kfree_skb_irq() to not queue a
skb if already orphaned, and to remove netpoll zap_completion_queue() as
a bonus.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>