Take txq lock in debug file and fix reporting of used buffers.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Prepare ath5k for WME by using four hardware queues.

The way we set up our queues matches the mac80211 queue priority 1:1, so we
don't have to do any mapping for queue numbers.

Every queue uses 50 of the total 200 available transmit buffers, so the DMA
memory usage does not increase with this patch, but it might be good to
fine-tune the number of buffers per queue later (depending on the CPU speed and
load, and the speed of the medium access, it might not be big enough).
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This change reorganizes the main ath5k file in order to re-group
related functions and remove most of the forward declarations
(from 61 down to 3).  This is, unfortunately, a lot of churn, but
there should be no functional changes.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixing up a merge issue / concurrent development:

Remove unneeded ath_crypt_caps flags, as per "ath9k_hw: remove useless hw
capability flags" (364734fa), but set the
AESCCM flag for ath9k. common ath code still needs a flag for this because
there is ath5k hardware which can't do AES in hardware.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch is loosely based on an ath9k patch called:
"ath9k_hw: sync initvals for ar9001 and ar9002 with Atheros"

It includes the following changes/fixes:
	- AGC setting improvements
	- timing changes for improved performance
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add MMC3 support on ZOOM, which has the wl1271 device hardwired to.

The wl1271 is a 4-wire, 1.8V, embedded SDIO WLAN device with an
external IRQ line, and power-controlled by a GPIO-based fixed regulator.
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a fixed regulator vmmc device to enable power control
of the wl1271 wlan device.
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The wl1271 device is using a reference clock that may change
between board to board.

Make the ref_clock parameter configurable by board settings
instead of having a hard coded value in the sources.
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove the hard coded irq information, and instead take
the irq information from the board's platform data.
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a simple mechanism to pass platform data to the
SDIO instances of wl12xx.

This way there is no confusion over who owns the 'embedded data',
typechecking is preserved, and no possibility for the wrong driver to
pick up the data.

Originally proposed by Russell King.
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make it possible for the set power method to indicate a
success/failure return value. This is needed to support
more complex power on/off operations such as SDIO
power manipulations.
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Acked-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move wl12xx.h outside of the spi-specific location,
so it can be shared with both spi and sdio solutions.

Update all users of spi/wl12xx.h accordingly
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Acked-by: NLuciano Coelho <luciano.coelho@nokia.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For config bt command, initialize both tx_prio_boost and
rx_prio_boost to "0".
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Adding two new parameters in config bt API. these two parameters
use the 3 reserved bytes, so there is no structure size changes.

Make sure set both parameters to "zero" in order to preserve
previous behavior.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

For failure tx status 0x90 and 0x91, give the correct name to reflect
the errors.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

remove duplicate header and clean up format so it is defined once
making changes consolicated ensuring consistancy of output.
no function change to date displayed.
Signed-off-by: NJay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Addition to standard tx frame failure report, adding aggregated
frame failure report to debugfs
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

When uCode completed the aggregated frames transmission attempt,
it will send tx command response with aggregated frame status.

Keep track of the failure counter which help indicate any transmission
error condition.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

For aggregated frames with block ack, different status flag
will be used as part of tx command response.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Tx command response sent to host by uCode after completed
the transmission attempt. The status parameter indicates
whether the transmission was successful, or else why if failed.

Here we keep the counters to help understand the different failure
cases.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

If uCode fail to transmit frame, it will send reply tx back
to driver with failure status; keep the counters of each failure
cases for debugging.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Include bt_status_read function pointer for 5150 device
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The patch titled "ath9k: Add new file init.c" shuffled some code
around but in dong so for some reason also removed the revision
check for disablign power save. Add this revision check again
so we can get power save re-enabled again by default on cards
newer than AR5416 and AR5418.

$ git describe --contains 55624204
v2.6.34-rc1~233^2~49^2~343

This patch has fixes for stable kernels [2.6.34+].

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch:

commit 293dc5df
Author: Gabor Juhos <juhosg@openwrt.org>
Date:   Fri Jun 19 12:17:48 2009 +0200

    ath9k: remove ath_rx_ps_back_to_sleep helper

    This helper only clears the SC_OP_WAIT_FOR_{BEACON,CAB} flags.
    Remove it and clear these flags directly in the approptiate
    places instead.

    Changes-licensed-under: ISC
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

introduced a regression which forgot to lift the beacon flag
after we received all broadcast and multicast data. This meant
we never went to sleep consuming about ~650mW on idle. This pretty
much broke power save completely.

This patch has fixes for stable kernels [2.6.32+].

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Sameer Nanda <snanda@google.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some buggy APs do not respond to unicast probe requests
or send unicast probe requests very delayed so in the
worst case we should try to send broadcast probe requests,
otherwise we can get disconnected from these APs.

Even if drivers do not have filters to disregard probe
responses from foreign APs mac80211 will only process
probe responses from our associated AP for re-arming
connection monitoring.

We need to do this since the beacon monitor does not
push back the connection monitor by design so even if we
are getting beacons from these type of APs our connection
monitor currently relies heavily on the way the probe
requests are received on the AP. An example of an AP
affected by this is the Nexus One, but this has also been
observed with random APs.

We can probably optimize this later by using null funcs
instead of probe requests.

For more details refer to:

http://code.google.com/p/chromium-os/issues/detail?id=5715

This patch has fixes for stable kernels [2.6.35+].

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The beacon monitor should be disabled when going off channel
to prevent spurious warnings and triggering connection
deterioration work such as sending probe requests. Re-enable
the beacon monitor once we come back to the home channel.

This patch has fixes for stable kernels [2.6.34+].

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This will be used by other components next. The beacon
monitor was added as of 2.6.34 so these fixes are applicable
only to kernels >= 2.6.34.

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we go offchannel mac80211 currently leaves alive the
connection idle monitor. This should be instead postponed
until we come back to our home channel, otherwise by the
time we get back to the home channel we could be triggering
unecesary probe requests. For APs that do not respond to
unicast probe requests (Nexus One is a simple example) this
means we essentially get disconnected after the probes
fails.

This patch has stable fixes for kernels [2.6.35+]

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Upon beacon loss we send probe requests after 30 seconds of idle
time and we wait for each probe response 1/2 second. We send a
total of 3 probe requests before giving up on the AP. In the case
that we reset the connection idle monitor we should reset the probe
requests count to 0. Right now this won't help in any way but
the next patch will.

This patch has fixes for stable kernel [2.6.35+].

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This will be used in another place later. The connection
monitor was added as of 2.6.35 so these fixes will be
applicable to >= 2.6.35.

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k's entire logic with SC_OP_SCANNING is incorrect due to the
way mac80211 currently implements the scan complete callback and
we handle it in ath9k. This patch removes the flag completely in
preference for the SC_OP_OFFCHANNEL which is really what we wanted.

The scanning flag was used to ensure we reset ANI to the old values
when we go back to the home channel, but if we are offchannel we
use some defaults. The flag was also used to re-enable the TX monitor.

Without this patch we simply never re-enabled ANI and the TX monitor
after going offchannel. This means that after one background
scan we are prone to noise issues and if we had a TX hang we would
not recover. To get this to work properly we must enable ANI after
we have configured the beacon timers, otherwise hardware acts really
oddly.

This patch has stable fixes which apply down to [2.6.36+], there
*may* be a to fix this on older kernels but requires a bit of
work since this patch relies on the new mac80211 flag
IEEE80211_CONF_OFFCHANNEL which was introduced as of 2.6.36.

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we return to the home channel we were never reseting our beacon
timers, this was casued by the fact that the scanning flag was still
on even after we returned to our home channel. There are also other
reasons why we would get a reset and if we are not off channel
we always need to resynch our beacon timers, because a reset will
clear them.

This bug is a regression introduced on 2.6.36. The order of the
changes are as follows:

5ee08656 - Sat Jul 31 - ath9k: prevent calibration during off-channel activity
a0daa0e7 - Tue Jul 27 - Revert "mac80211: fix sw scan bracketing"
543708be - Fri Jun 18 - mac80211: fix sw scan bracketing

mcgrof@tux ~/linux-2.6-allstable (git::master)$ git describe \
        --contains 5ee08656
v2.6.36-rc1~43^2~34^2~22

mcgrof@tux ~/linux-2.6-allstable (git::master)$ git describe \
        --contains a0daa0e7
v2.6.36-rc1~571^2~64^2~13

mcgrof@tux ~/linux-2.6-allstable (git::master)$ git describe \
        --contains 543708be
v2.6.36-rc1~571^2~107^2~187

So 5ee08656 would have worked if a0daa0e7 was not committed but
it was so this means 5ee08656 was broken since it assumed that
when we were in the channel change routine the scan flag would
be lifted. As it turns out the scan flag will be set when we
are already on the home channel.

For more details refer to:

http://code.google.com/p/chromium-os/issues/detail?id=5715

These issues will need to be considered for our solution on
reshifting the scan complete callback location on mac80211 on
current development kernel work.

This patch has stable fixes which apply down to [2.6.36+]

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k has a race on putting the chip into network sleep and
having registers read from hardware. The race occurs because
although ath9k_ps_restore() locks its own callers it makes use
of some variables which get altered in the driver at different
code paths. The variables are the ps_enabled and ps_flags.

This is easily reprodicible in large network environments when
roaming with the wpa_supplicant simple bgscan. You'd get some
0xdeadbeef read out on certain registers such as:

ath: timeout (100000 us) on reg 0x806c: 0xdeadbeef & 0x01f00000 != 0x00000000
ath: RX failed to go idle in 10 ms RXSM=0xdeadbeef

ath: timeout (100000 us) on reg 0x7000: 0xdeadbeef & 0x00000003 != 0x00000000
ath: Chip reset failed

The fix is to protect the ath9k_config(hw, IEEE80211_CONF_CHANGE_PS)
calls with a spin_lock_irqsave() which will disable contendors for
these variables from interrupt context, timers, re-entry from mac80211
on the same callback, and most importantly from ath9k_ps_restore()
which is the only call which will put the device into network sleep.

There are quite a few threads and bug reports on these a few of them are:

https://bugs.launchpad.net/ubuntu/karmic/+source/linux/+bug/407040
http://code.google.com/p/chromium-os/issues/detail?id=5709
http://code.google.com/p/chromium-os/issues/detail?id=5943

Stable fixes apply to [2.6.32+]

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To optimize register read/write operations, the HTC firmwares were patched
to change EP3 and EP4 pipe types from Interrupt to Bulk. So register writes
are submitted as bulk urbs, but register reads are not. Also changing the
register read endpoint pipe as bulk type when URBs are filled improves the
register reads considerably which results in reduced scan time and CPU
utilization.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a driver advertises p2p device support,
mac80211 will handle it, but internally it will
rewrite the interface type to STA/AP rather than
P2P-STA/GO since otherwise a lot of paths need
to be touched that are otherwise identical. A
p2p boolean tells drivers whether or not a given
interface will be used for p2p or not.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds P2P-STA and P2P-GO as device types so
we can distinguish between those and normal STA
or AP (respectively) type interfaces.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes following warning

drivers/net/wireless/ath/ath9k/eeprom_def.c: In function 'ath9k_hw_def_get_num_ant_config'
drivers/net/wireless/ath/ath9k/eeprom_def.c:1425:47: warning: comparison
			between 'enum ath9k_hal_freq_band' and 'enum ieee80211_band'
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

  CHECK   drivers/net/wireless/libertas/cfg.c
drivers/net/wireless/libertas/cfg.c:493:19: warning: cast to restricted __le16
  CHECK   drivers/net/wireless/libertas/mesh.c
drivers/net/wireless/libertas/mesh.c:577:16: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/mesh.c:577:16:    expected restricted __le32 [addressable] [assigned] [usertype] id
drivers/net/wireless/libertas/mesh.c:577:16:    got bool
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

  CHECK   drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/ath/ath9k/recv.c:1341:6: warning: symbol 'ath_ant_div_conf_fast_divbias' was not declared. Should it be static?
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/wireless/iwlwifi/iwl-scan.c:386:27: warning: mixing different enum types
drivers/net/wireless/iwlwifi/iwl-scan.c:386:27:     int enum nl80211_band  versus
drivers/net/wireless/iwlwifi/iwl-scan.c:386:27:     int enum ieee80211_band
drivers/net/wireless/iwlwifi/iwl-scan.c:435:57: warning: mixing different enum types
drivers/net/wireless/iwlwifi/iwl-scan.c:435:57:     int enum ieee80211_band  versus
drivers/net/wireless/iwlwifi/iwl-scan.c:435:57:     int enum nl80211_band
drivers/net/wireless/iwlwifi/iwl-scan.c:474:53: warning: mixing different enum types
drivers/net/wireless/iwlwifi/iwl-scan.c:474:53:     int enum ieee80211_band  versus
drivers/net/wireless/iwlwifi/iwl-scan.c:474:53:     int enum nl80211_band
drivers/net/wireless/iwlwifi/iwl-scan.c:588:72: warning: mixing different enum types
drivers/net/wireless/iwlwifi/iwl-scan.c:588:72:     int enum ieee80211_band  versus
drivers/net/wireless/iwlwifi/iwl-scan.c:588:72:     int enum nl80211_band
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>