This patch adds base support for new i354 devices.  Loopback test is
unsupported for this release.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for spoofchk configuration per VF via iproute2 tool.
Signed-off-by: NLior Levy <lior.levy@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On EEE-capable devices, query the PHY to determine what the link partner is
advertising.
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Aligns the multi-line code comments with the desired style for the
networking tree.  Also cleaned up whitespace issues found during the
cleanup of code comments (i.e. remove unnecessary blank lines,
use tabs where possible, properly wrap lines and keep strings on a
single line)
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>

This patch fixes sparse warnings on function pointers that are not
defined as static.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It turns out that the InterruptThrottleRate module parameter was only
having the effect of locking the ITR at the starting ITR value. This was
because the values stored in rx_itr_setting and tx_itr_setting were being
ignored when configuring the initial itr_val of the q_vector.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We only need the adapter pointer in the case of ptp.  As such we can pull the
adapter out of the main path and place it inside the if statement to avoid
the temptation of accessing the adapter pointer in the fast path.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We were incorrectly checking the entire frag_off field when we only wanted the
fragment offset.  As a result we were not pulling in TCP headers when the DNF
flag was set.

To correct that we will now check for frag off using the IP_OFFSET mask.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes code and comments as identified in the driver.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on original patch from Aurélien Guillaume <footplus@gmail.com>
This patch adds support to turn on I2C, with sfp cage powered.

CC: Aurélien Guillaume <footplus@gmail.com>
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support to read and export SFF-8472/8079 (SFP data)
over i2c, through Ethtool.

v2: Changed implementation to accommodate any offset within SFF module
    length boundary.
Reported-by: NAurélien Guillaume <footplus@gmail.com>
CC: Aurélien Guillaume <footplus@gmail.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for 100base-fx SFP and report proper link speed/duplex
via Ethtool.

v2: fix smatch warnings

CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add some empty static inlines instead to make
the code more readable.
Signed-off-by: NJoe Perches <joe@perches.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds software support for WoL for the 82599 SFP+ LOM device,
(ID 0x8976)
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

During shutdown it's possible for __dev_close() (which holds
rtnl_lock) to clear the __LINK_STATE_START bit, and for ixgbe
to then read that bit (without holding rtnl_lock), and then
not fail to free irqs, etc. The result is a crash like this:

------------[ cut here ]------------
kernel BUG at drivers/pci/msi.c:313!
invalid opcode: 0000 [#1] SMP
last sysfs file: /sys/devices/system/cpu/cpu3/cache/index2/shared_cpu_map
CPU 1
Pid: 5910, comm: reboot Tainted: P           ----------------   2.6.32 #1 empty
RIP: 0010:[<ffffffff81305c2b>]  [<ffffffff81305c2b>] free_msi_irqs+0x11b/0x130
RSP: 0018:ffff880185c9bc88  EFLAGS: 00010282
RAX: ffff880219f58bc0 RBX: ffff88021ac53b00 RCX: 0000000000000000
RDX: 0000000000000001 RSI: 0000000000000246 RDI: 000000000000004a
RBP: ffff880185c9bcc8 R08: 0000000000000002 R09: 0000000000000106
R10: 0000000000000000 R11: 0000000000000006 R12: ffff88021e524778
R13: 0000000000000001 R14: ffff88021e524000 R15: 0000000000000000
FS:  00007f90821b7700(0000) GS:ffff880028220000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00007f90818bd010 CR3: 0000000132c64000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process reboot (pid: 5910, threadinfo ffff880185c9a000, task ffff88021bf04a80)
Stack:
 ffff880185c9bc98 000000018130529d ffff880185c9bcc8 ffff88021e524000
<0> 0000000000000004 ffff88021948c700 0000000000000000 ffff880185c9bda7
<0> ffff880185c9bce8 ffffffff81305cbd ffff880185c9bce8 ffff88021948c700
Call Trace:
 [<ffffffff81305cbd>] pci_disable_msix+0x3d/0x50
 [<ffffffffa00501d5>] ixgbe_reset_interrupt_capability+0x65/0x90 [ixgbe]
 [<ffffffffa00512f6>] ixgbe_clear_interrupt_scheme+0xb6/0xd0 [ixgbe]
 [<ffffffffa005330b>] __ixgbe_shutdown+0x5b/0x200 [ixgbe]
 [<ffffffffa00534ca>] ixgbe_shutdown+0x1a/0x60 [ixgbe]
 [<ffffffff812f6c7c>] pci_device_shutdown+0x2c/0x50
 [<ffffffff813727fb>] device_shutdown+0x4b/0x160
 [<ffffffff8107d98c>] kernel_restart_prepare+0x2c/0x40
 ehci timer_action, mod_timer io_watchdog
 [<ffffffff8107d9e6>] kernel_restart+0x16/0x60
 [<ffffffff8107dbfd>] sys_reboot+0x1ad/0x200
 [<ffffffff811676cf>] ? __d_free+0x3f/0x60
 [<ffffffff81167748>] ? d_free+0x58/0x60
 [<ffffffff8116f7c0>] ? mntput_no_expire+0x30/0x100
 [<ffffffff81152b11>] ? __fput+0x191/0x200
 [<ffffffff816565fe>] ? do_page_fault+0x3e/0xa0
 [<ffffffff8100b132>] system_call_fastpath+0x16/0x1b
Code: 4c 89 ef e8 98 8c e3 ff 4d 39 f4 48 8b 43 10 75 cf 48 83 c4 18 5b 41 5c
41 5d 41 5e 41 5f c9 c3 49 8b 7d 20 e8 07 5a d3 ff eb c9 <0f> 0b 0f 1f 00 eb fb
66 66 66 66 66 2e 0f 1f 84 00 00 00 00 00
 ehci timer_action, mod_timer io_watchdog
RIP  [<ffffffff81305c2b>] free_msi_irqs+0x11b/0x130
 RSP <ffff880185c9bc88>
---[ end trace 27de882a0fe75593 ]---

(This was seen on a pretty old kernel/driver, but looks like
the same bug is still possible.)

Signed-off-by: <akepner@riverbed.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Jeff Kirsher says:

====================
This series contains updates to ixgbe only.

v2- Dropped the following 2 patches from the series:
 ixgbe: Support using build_skb in the case that jumbo frames are disabled
 ixgbe: walk pci-e bus to find minimum width

Ben Hutchings found a bug with Alex's patch, so that patch was dropped
permanently.  Jacob's "walk PCIe bus" patch is being re-worked for
a more generic solution so that other drivers can benefit.

In the remaining patches...
Alex provides a fix where we were incorrectly checking the entire frag_off
field when we only wanted the fragment offset.  Alex also cleans up
the check for PAGE_SIZE, since the default configuration allocates 32K
for all buffers.

Emil provides a change to the calculation of eerd so that it is consistent
between the read and write functions by using | instead of +.

Jacob adds support for displaying PCIe Gen3 link speed, which was
previously missing from the ixgbe driver.  He also provides a patch
to clean up ixgbe_get_bus_info_generic to call some conversion
functions, which are used also in another patch provided by Jacob.
Jacob modifies the driver to enable certain devices (which have an
internal switch) to read from the physical slot rather than reading
data from the internal switch.

Don provides a couple of fixes (which are more appropriate for net-next),
one of which resolves an issue where ixgbe was only turning on the laser
when the adapter was up which caused issues for those who wanted to
access the MNG firmware while the port was in a down state.  The other
fix is for WoL when currently linked at 1G.  Lastly Don bumps the driver
version keep the in-kernel driver up to date with the current functionality.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Host queues (Qdisc + NIC) can hold packets so long that TCP can
eventually retransmit a packet before the first transmit even left
the host.

Its not clear right now if we could avoid this in the first place :

- We could arm RTO timer not at the time we enqueue packets, but
  at the time we TX complete them (tcp_wfree())

- Cancel the sending of the new copy of the packet if prior one
  is still in queue.

This patch adds instrumentation so that we can at least see how
often this problem happens.

TCPSpuriousRtxHostQueues SNMP counter is incremented every time
we detect the fast clone is not yet freed in tcp_transmit_skb()
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is nothing in the driver that requires <asm/coldfire.h> and
<asm/mcfsim.h>.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bump the version number reflect the corresponding functionality in the
out of tree driver.
Signed-of-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We reset during the shutdown path which will reset AUTOC register.  This
would change LMS to 10G.  If we were currently linked at 1G we will lose
link, which is a bad thing if we wanted WoL to work.  For the fix I needed
to know if WoL is supported so I created a new bool in the ixgbe_hw struct.
If this is set we will not allow the reset to change the current LMS value
in AUTOC.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We were only turning the laser on when the adapter was up.  This
causes issues for those who wanted to access the MNG FW while the
port was in a down state.  This patch makes sure the laser is turned
on in probe and remain up even after the port is brought down.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch modifies the driver to enable certain devices, which have an internal
switch, to read data from the physical slot rather than reading data from the
internal switch. The internal switch will always report the same PCI width and
speed, which is not useful compared to knowing the width and speed of the slot
the physical card is plugged into.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch cleans up ixgbe_get_bus_info_generic to call some conversion
functions, which are used also in a follow on patch that needs to convert
between the link_status PCIe config values into ixgbe's internal enum
representations.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for displaying PCIe Gen3 link speed, which was
previously missing from the driver.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The check for PAGE_SIZE is pointless now that the default configuration is to
allocate 32K for all buffers.  Since the Tx descriptor limit is 16K we can
just drop the check and always compare the descriptors to the maximum size
supported.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make the calculation of eerd consistent between the read and write functions
by using | instead of + for IXGBE_EEPROM_RW_REG_START
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We were incorrectly checking the entire frag_off field when we only wanted the
fragment offset.  As a result we were not pulling in TCP headers when the DNF
flag was set.

To correct that we will now check for frag off using the IP_OFFSET mask.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Patrick McHardy says:

====================
The following patchset adds support for running TIPC over InfiniBand.
The patchset consists of three parts (+ a minor fix for the ethernet media
type):

- Preparation: removal of an the unused str2addr callback and move of the
  bcast_addr from struct tipc_media to struct tipc_bearer. This is necessary
  because InfiniBand doesn't have a fixed broadcast address like ethernet,
  so it needs to be initialized with the device's broadcast address when
  the bearer is enabled

- Introduction of a TIPC InfiniBand media type. A new media type is needed
  to deal with the different address sizes

- Support for ETH_P_TIPC in IPoIB

Since the last posting I've addressed all feedback I received and rebased
to the current net-next tree.

I consider these patches ready for merging. Since they mainly affect TIPC
code, I'd propose to have them either go through the TIPC tree or through
Dave directly (not sure how TIPC patches are managed).
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support TIPC in the IPoIB driver. Since IPoIB now keeps track of its own
neighbour entries and doesn't require the packet to have a dst_entry
anymore, the only necessary changes are to:

- not drop multicast TIPC packets because of the unknown ethernet type
- handle unicast TIPC packets similar to IPv4/IPv6 unicast packets

in ipoib_start_xmit().

An alternative would be to remove all ethertype limitations since they're
not necessary anymore, all TIPC needs to know about is ARP and RARP since
it wants to always perform "path find", even if a path is already known.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add InfiniBand media type based on the ethernet media type.

The only real difference is that in case of InfiniBand, we need the entire
20 bytes of space reserved for media addresses, so the TIPC media type ID is
not explicitly stored in the packet payload.

Sample output of tipc-config:

# tipc-config -v -addr -netid -nt=all -p -m -b -n -ls

node address: <10.1.4>
current network id: 4711
Type       Lower      Upper      Port Identity              Publication Scope
0          167776257  167776257  <10.1.1:1855512577>        1855512578  cluster
           167776260  167776260  <10.1.4:1216454657>        1216454658  zone
1          1          1          <10.1.4:1216479235>        1216479236  node
Ports:
1216479235: bound to {1,1}
1216454657: bound to {0,167776260}
Media:
eth
ib
Bearers:
ib:ib0
Nodes known:
<10.1.1>: up
Link <broadcast-link>
  Window:20 packets
  RX packets:0 fragments:0/0 bundles:0/0
  TX packets:0 fragments:0/0 bundles:0/0
  RX naks:0 defs:0 dups:0
  TX naks:0 acks:0 dups:0
  Congestion bearer:0 link:0  Send queue max:0 avg:0

Link <10.1.4:ib0-10.1.1:ib0>
  ACTIVE  MTU:2044  Priority:10  Tolerance:1500 ms  Window:50 packets
  RX packets:80 fragments:0/0 bundles:0/0
  TX packets:40 fragments:0/0 bundles:0/0
  TX profile sample:22 packets  average:54 octets
  0-64:100% -256:0% -1024:0% -4096:0% -16384:0% -32768:0% -66000:0%
  RX states:410 probes:213 naks:0 defs:0 dups:0
  TX states:410 probes:197 naks:0 acks:0 dups:0
  Congestion bearer:0 link:0  Send queue max:1 avg:0
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The skb->protocol field is used by packet classifiers and for AF_PACKET
cooked format, TIPC needs to set it properly.

Fixes packet classification and ethertype of 0x0000 in cooked captures:

Out 20:c9:d0:43:12:d9 ethertype Unknown (0x0000), length 56:
	0x0000:  5b50 0028 0000 30d4 0100 1000 0100 1001  [P.(..0.........
	0x0010:  0000 03e8 0000 0001 20c9 d043 12d9 0000  ...........C....
	0x0020:  0000 0000 0000 0000                      ........
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some network protocols, like InfiniBand, don't have a fixed broadcast
address but one that depends on the configuration. Move the bcast_addr
to struct tipc_bearer and initialize it with the broadcast address of
the network device when the bearer is enabled.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove warning introduced by commit 418fc57a ("usbnet: cdc-ether: apply
usbnet_link_change"):

   CHECK   .../drivers/net/usb/cdc_ether.c
 .../drivers/net/usb/cdc_ether.c:409:46: warning: incorrect type in argument 2 (different base types)
 .../drivers/net/usb/cdc_ether.c:409:46:    expected bool [unsigned] [usertype] <noident>
 .../drivers/net/usb/cdc_ether.c:409:46:    got restricted __le16 [usertype] wValue

Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Acked-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The structure sctp_ulpq is embedded into sctp_association and never
separately allocated, also ulpq->malloced is always 0, so that
kfree() is never called. Therefore, remove this code.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sctp_bind_addr structure has a 'malloced' member that is
always set to 0, thus in sctp_bind_addr_free() the kfree()
part can never be called. This part is embedded into
sctp_ep_common anyway and never alloced.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sctp_transport's member 'malloced' is set to 1, never evaluated
and the structure is kfreed anyway. So just remove it.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just a minor edit to simplify the function. No need for this
error variable here.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sctp_outq is embedded into sctp_association, and thus never
kmalloced in any way. Also, malloced is always 0, thus kfree()
is never called. Therefore, remove that dead piece of code.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sctp_inq is never kmalloced, since it's integrated into sctp_ep_common
and only initialized from eps and assocs. Therefore, remove the dead
code from there.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>