Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 17 4月, 2015 5 次提交
  3. 15 4月, 2015 5 次提交
    • P
      ath: lower JP W53 band DFS detection threshold around 30% · 26bea13a
      由 Peter Oh 提交于 
      Japan's W53 band requires 50% data traffic during its DFS test,
but WLAN baseband used by ath9k and ath10k is not able to achieve
current threshold rate, 50%, under the data traffic rate.
In other words, HW occasionally fails detecting radar pulses,
so that SW cannot get enough radar reports to achieve the rate.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      26bea13a
    • P
      ath: define JP DFS patterns separated from FCC · cb3fbd63
      由 Peter Oh 提交于 
      Separate Japan's DFS pattern from FCC to control PPB threshold.

Currently all the radar detectors use the same threshold rate at
50%, but it's not able to achieve if data traffic rate is higher
than 40% because WLAN baseband used by ath9k and ath10k often fails
detecting radar pulses, so that SW cannot get enough radar reports
to achieve the rate.

Since Japan's W53 band requires 50% data traffic during its DFS
test we need to apply different threshold rate than others on it.
Hence define its own pattern to give flexibility to threshold rate.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      cb3fbd63
    • M
      ath10k: use scan burst for hw roc · dbd3f9f3
      由 Michal Kazior 提交于 
      This improves chances of getting onto a foreign
channel and thus makes P2P a bit more reliable.

Without scan burst it was possible for firmware to
not switch to foreign channel resulting in "failed
to switch to channel for roc scan" warning. This
would also effectively fail some offchan tx
requests and lead to P2P find/connect taking
longer. This could be observed when other vifs
were running/busy, e.g. with P2P GO.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      dbd3f9f3
    • M
      ath10k: fix hw roc expiration · fcf98446
      由 Michal Kazior 提交于 
      It is not guaranteed firmware will switch to
foreign channel immediately after starting scan
sequence. To account for that don't use duration
parameter for scan time. Instead request insanely
long scan and use timeout worker to cancel it from
driver.

This should improve P2P reliability a bit.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      fcf98446
    • P
      ath: support new FCC DFS Radar Type 1 · 694c0e0a
      由 Peter Oh 提交于 
      Add support for new FCC DFS rules released on August 14, 2014.
FCC has added a new radar type named Radar Type 1 and original
Radar Type 1 is renamed to Radar Type 0 in consequence.

During the certificate test, Type 1 PRI values are randomly selected
within the range of 518 and 3066 and we divide it to 3 groups based on
practical test result data collected for more than a year.

For about Radar type ID, it does nothing to functionalities.
In other words, even if we re-order the IDs, DFS detection will
work as well, but we give the ID with matching to FCC doc.

By adding this support, the drivers using this DFS function are
able to support both of old and new FCC DFS rules simultaneously
without any other changes.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      694c0e0a
  5. 09 4月, 2015 7 次提交
  7. 02 4月, 2015 17 次提交
  9. 30 3月, 2015 6 次提交