This patch adds basic board support for phytecs pmc037 board.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Currently there is a mx31ads BSP file in the kernel, but no default
config file.

This patch adds a basic default config for the imx31ads but it is for test
purposes only to ensure the i.MX2 patch stack doesn't break the i.MX3.

Note: For reference only. This configuration is untested as I have
no access to an mx31ads.
Signed-off-by: NJuergen Beisert <j.beisert@pengutronix.de>

This patch adds debug-macro.S for arch-mxc

Disadvantage: Due to the board specific UART definition, these macros (and
compile time) will fail for multi board kernels.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch adds timer support for the i.MX machine family. This code can
be used on the following machs:

 - i.MX1 (tested)
 - i.MX2 (i.MX21 (to be tested), i.MX27 (tested))
 - i.MX3 (i.MX31 (tested))

TODO: It seems impossible to build a kernel for more than one CPU because the
timer do not follow the platform device rules. So it does only work if
timer 1 can be accessed on all CPUs at the same address.
Signed-off-by: NJuergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch adds functions to use the io multiplexer on mx3 platforms.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch bases on the one from Daniel Mack. The most important change to
Daniel's patch is to be more generic. This gpio routine supports at least
the i.MX27 and i.MX31 processors.
Signed-off-by: NJuergen Beisert <j.beisert@pengutronix.de>
Acked-by: NDaniel Mack <daniel@caiaq.de>

This patch adds MX3 support for the i.MX internal uart driver.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch introduces the clock API for for arch-mxc
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Internal clock path handling for the mxc CPUs.

Changed against the original Freescale code (and against clocklib for example):
 - clock rate is always calculated whenever one ask for the current rate
   (means struct clk has no more a member called "rate"). So switching the PLL
   base frequency will propagate immediately to all other clocks that are
   depending on this frequency.
Signed-off-by: NJuergen Beisert <j.beisert@pengutronix.de>

This patch introduces the clock API for i.MX and converts all
in-Kernel drivers to use it.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch removes the statically initialized tables from the i.MX serial
driver and makes the driver fully dependent on the information provided by
the platform_device.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add platform specific init functions. Also rename the struct
platform_device dev into pdev.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

We assumed a 16MHz reference frequency for the UART. While this
is true for i.MX1 most of the time it is not true for MX27/MX31.
Also, add handling for the ONEMS register which is present on
newer versions of the chip and pass a sane minimum baudrate to
uart_get_baud_rate().
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

do not include board-mx31ads.h from hardware.h, instead include it
directly only where needed.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: adding comment for ipaq forcing number of ports
  USB: fix Oops on loading ipaq module since 2.6.26
  USB: add a pl2303 device id
  USB: another option device id
  USB: don't lose disconnections during suspend
  USB: fix interrupt disabling for HCDs with shared interrupt handlers
  USB: New device ID for ftdi_sio driver
  sisusbvga: Fix oops on disconnect.
  USB: mass storage: new id for US_SC_CYP_ATACB
  USB: ohci - record data toggle after unlink
  USB: ehci - fix timer regression
  USB: fix cdc-acm resume()
  OHCI: Fix problem if SM501 and another platform driver is selected

The reason for forcing a number of ports should be documented.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixes bugzilla.kernel.org #10868
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

As reported by Ken A Scott <kscott9@sent.com>

Cc: Ken A Scott <kscott9@sent.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Thanks to umesh b <umesh.kollam@gmail.com> for the information here.

Cc: umesh b <umesh.kollam@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1111) fixes a bug in the hub driver.  When a hub
resumes, disconnections that occurred while the hub was suspended are
lost.

A completely different fix for this problem has already been accepted
for 2.6.27; however the problem still needs to be handled in 2.6.26.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NLukas Hejtmanek <xhejtman@ics.muni.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB: fix interrupt disabling for HCDs with shared interrupt handlers

As has been discussed several times on LKML, IRQF_SHARED | IRQF_DISABLED
doesn't work reliably, i.e. a shared interrupt handler CAN'T be certain to
be called with interrupts disabled. Most USB HCD handlers use IRQF_DISABLED
and therefore havoc can break out if they share their interrupt with a
handler that doesn't use it.

On my test machine the yenta_socket interrupt handler (no IRQF_DISABLED)
was registered before ehci_hcd and one uhci_hcd instance. Therefore all
usb_hcd_irq() invocations for ehci_hcd and for one uhci_hcd instance
happened with interrupts enabled. That led to random lockups as USB core
HCD functions that acquire the same spinlock could be called twice
from interrupt handlers.

This patch updates usb_hcd_irq() to always disable/restore interrupts.
usb_add_hcd() will silently remove any IRQF_DISABLED requested from HCD code.
Signed-off-by: NStefan Becker <stefan.becker@nokia.com>
Cc: stable <stable@kernel.org>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Here's a new device ID for the ftdio_sio driver.
The diff is with linus's tree as of this morning.

The device is the RigExpert Tiny USB Soundcard Transceiver Interface for ham
radio.

(I didn't actually test this. A fellow ham couldn't get the device to work, and
I suggested binding the device ID using sysfs - see
"http://jk.ufisa.uninett.no/usb/". However, he had had moved on to other things
by then. I guess adding the device ID to the kernel "on spec" won't hurt.
The relevant part of cat /proc/bus/usb/devices shows:

T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0403 ProdID=ed22 Rev= 5.00
S:  Manufacturer=FTDI
S:  Product=MixW RigExpert Tiny
S:  SerialNumber=00000000
C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=83(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
)

From: Jon K Hellan <hellan@acm.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove dev_info call on disconnect. The sisusb_dev pointer may have been
set to zero by sisusb_delete at this point causing an oops.

The message does not provide any extra information over the standard USB
subsystem output so removing it does not affect functionality.
Signed-off-by: NWill Newton <will.newton@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

CY7C68310 chip also support cypress atacb "ATA command" pass_thru.
Signed-off-by: NMatthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes a problem with OHCI where canceling bulk or
interrupt URBs may lose track of the right data toggle.  This
seems to be a longstanding bug, possibly dating back to the
Linux 2.4 kernel, which stayed hidden because

 (a) about half the time the data toggle bit was correct;
 (b) canceling such URBs is unusual; and
 (c) the few drivers which cancel these URBs either
      [1] do it only as part of shutting down, or
      [2] have fault recovery logic, which recovers.

For those transfer types, the toggle is normally written back
into the ED when each TD is retired.  But canceling bypasses
the mechanism used to retire TDs ... so on average, half the
time the toggle bit will be invalid after cancelation.

The fix is simple:  the toggle state of any canceled TDs are
propagated back to the ED in the finish_unlinks function.

(Issue found by leonidv11@gmail.com ...)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Leonid <leonidv11@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes a regression in the EHCI driver's TIMER_IO_WATCHDOG
behavior.  The patch "USB: EHCI: add separate IAA watchdog timer" changed
how that timer is handled, so that short timeouts on the remaining
timer (unfortunately, overloaded) would never be used.

This takes a more direct approach, reorganizing the code slightly to
be explicit about only the I/O watchdog role now being overridable.
It also replaces a now-obsolete comment describing older timer behavior.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Leonid <leonidv11@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

cdc-acm has
- a memory leak in resume()
- will fail to reactivate the read code path if this is needed.
his corrects it by deleting the useless relict code.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If the SM501 and another platform driver, such as the SM501
then we end up defining PLATFORM_DRIVER twice. This patch
seperated the SM501 onto a seperate define of SM501_OHCI_DRIVER
so that it can be selected without overwriting the original
definition.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

To return garbage_args, the accept_stat must be 0, and we must have a
verifier.  So we shouldn't be resetting the write pointer as we reject
the call.

Also, we must add the two placeholder words here regardless of success
of the unwrap, to ensure the output buffer is left in a consistent state
for svcauth_gss_release().

This fixes a BUG() in svcauth_gss.c:svcauth_gss_release().

Thanks to Aime Le Rouzic for bug report, debugging help, and testing.
Signed-off-by: NJ. Bruce Fields <bfields@citi.umich.edu>
Tested-by: NAime Le Rouzic <aime.le-rouzic@bull.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] cevt-txx9: Reset timer counter on initialization
  [MIPS] IP22: Fix crashes due to wrong L1_CACHE_BYTES
  [MIPS] IP32: Fix unexpected irq 71

Due to a possible deadlock, the waking of the softirq was pushed outside
of the hrtimer base locks. See commit 0c96c597

Unfortunately this allows the task to migrate after setting up the softirq
and raising it. Since softirqs run a queue that is per-cpu we may raise the
softirq on the wrong CPU and this will keep the queued softirq task from
running.

To solve this issue, this patch disables preemption around the releasing
of the hrtimer lock and raising of the softirq.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The txx9_tmr_init() will not clear a timer counter register in a certain
case.  The counter register is cleared on 1->0 transition of TCE bit if
CRE=1.  So just clearing the TCE bit is not enough.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The introduction of a real dma cache invalidate makes it important
to have a correct cache line size, otherwise the kernel will gives
out two memory segment, which might share one cache line. The R4400
Indy/Indigo2 CPU modules are using a second level cache line size
of 128 bytes, so MIPS_L1_CACHE_SHIFT needs to be bumped up to 7 for
IP22.
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

It's possible that the crime interrupt handler is called without
pending interrupts (probably a hardware issue). To avoid irritating
"unexpected irq 71" messages, we now just ignore the spurious crime
interrupts.
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  9p: fix O_APPEND in legacy mode

The non-NUMA case of build_zonelist_cache() would initialize the
zlcache_ptr for both node_zonelists[] to NULL.

Which is problematic, since non-NUMA only has a single node_zonelists[]
entry, and trying to zero the non-existent second one just overwrote the
nr_zones field instead.

As kswapd uses this value to determine what reclaim work is necessary,
the result is that kswapd never reclaims.  This causes processes to
stall frequently in low-memory situations as they always direct reclaim.
This patch initialises zlcache_ptr correctly.
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Tested-by: NDan Williams <dan.j.williams@intel.com>
[ Simplified patch a bit ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The legacy protocol's open operation doesn't handle an append operation
(it is expected that the client take care of it).  We were incorrectly
passing the extended protocol's flag through even in legacy mode.  This
was reported in bugzilla report #10689.  This patch fixes the problem
by disallowing extended protocol open modes from being passed in legacy
mode and implemented append functionality on the client side by adding
a seek after the open.
Signed-off-by: NEric Van Hensbergen <ericvh@gmail.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI: acpiphp: cleanup notify handler on all root bridges
  PCI: Limit VPD read/write lengths for Broadcom 5706, 5708, 5709 rev.
  PCI: Restrict VPD read permission to root

* 'i2c-fix' of git://aeryn.fluff.org.uk/bjdooks/linux:
  I2C: S3C2410: Add MODULE_ALIAS() for s3c2440 device.
  I2C: S3C2410: Fixup error codes returned rom a transfer.
  I2C: S3C2410: Check ACK on byte transmission

* 'for-2.6.26' of git://git.kernel.dk/linux-2.6-block:
  Properly notify block layer of sync writes
  block: Fix the starving writes bug in the anticipatory IO scheduler