Mark the thermal init functions __init so that the init memory
can be freed.
Signed-off-by: NYong Wang <yong.y.wang@intel.com>
LKML-Reference: <20091111075125.GA17900@ywang-moblin2.bj.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

On platforms where the BIOS handles the thermal monitor interrupt,
APIC_LVTTHMR on each logical CPU is programmed to generate a SMI
and OS must not touch it.

Unfortunately AP bringup sequence using INIT-SIPI-SIPI clears all
the LVT entries except the mask bit. Essentially this results in
all LVT entries including the thermal monitoring interrupt set
to masked (clearing the bios programmed value for APIC_LVTTHMR).

And this leads to kernel take over the thermal monitoring
interrupt on AP's but not on BSP (leaving the bios programmed
value only on BSP).

As a result of this, we have seen system hangs when the thermal
monitoring interrupt is generated.

Fix this by reading the initial value of thermal LVT entry on
BSP and if bios has taken over the control, then program the
same value on all AP's and leave the thermal monitoring
interrupt control on all the logical cpu's to the bios.
Signed-off-by: NYong Wang <yong.y.wang@intel.com>
Reviewed-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Arjan van de Ven <arjan@infradead.org>
LKML-Reference: <20091110013824.GA24940@ywang-moblin2.bj.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: stable@kernel.org

Add an early initcall (pre SMP) which sets up global MCE
functionality.
Signed-off-by: NBorislav Petkov <borislav.petkov@amd.com>
Cc: Andi Kleen <andi@firstfloor.org>
LKML-Reference: <1255689093-26921-2-git-send-email-borislav.petkov@amd.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Prefix global/setup routines with "mcheck_" thus differentiating
from the internal facilities prefixed with "mce_". Also, prefix
the per cpu calls with mcheck_cpu and rename them to reflect the
MCE setup hierarchy of calls better.

There should be no functionality change resulting from this
patch.
Signed-off-by: NBorislav Petkov <borislav.petkov@amd.com>
Cc: Andi Kleen <andi@firstfloor.org>
LKML-Reference: <1255689093-26921-1-git-send-email-borislav.petkov@amd.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Merge reason: Put all MCE changes into this branch, we are
              queueing up a dependent patch.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The MCE initialization code explicitly says it doesn't handle
asymmetric configurations where different CPUs support different
numbers of MCE banks, and it prints a big warning in that case.

Therefore, printing the "mce: CPU supports <x> MCE banks"
message into the kernel log for every CPU is pure redundancy
that clutters the log significantly for systems with lots of
CPUs.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
LKML-Reference: <adaeip473qt.fsf@cisco.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

A few parts of the uv_hub_info structure are initialized
incorrectly.

 - n_val is being loaded with m_val.
 - gpa_mask is initialized with a bytes instead of an unsigned long.
 - Handle the case where none of the alias registers are used.

Lastly I converted the bau over to using the uv_hub_info->m_val
which is the correct value.

Without this patch, booting a large configuration hits a
problem where the upper bits of the gnode affect the pnode
and the bau will not operate.
Signed-off-by: NRobin Holt <holt@sgi.com>
Acked-by: NJack Steiner <steiner@sgi.com>
Cc: Cliff Whickman <cpw@sgi.com>
Cc: stable@kernel.org
LKML-Reference: <20091015224946.396355000@alcatraz.americas.sgi.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Older binutils breaks if ASSERT() is used without a sink
for the output.

For example 2.14.90.0.6 is known to be broken, the link
fails with:

  LD      .tmp_vmlinux1
  ld:arch/x86/kernel/vmlinux.lds:678: parse error

Document this quirk in all three files that use it.

  See:    http://marc.info/?l=linux-kbuild&m=124930110427870&w=2
  See[2]: d2ba8b21 ("x86: Fix assert syntax in vmlinux.lds.S")

Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Roland McGrath <roland@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <4AD6523D.5030909@zytor.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

* 'docs-next' of git://git.lwn.net/linux-2.6:
  Update flex_arrays.txt

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
  dlm: fix socket fd translation
  dlm: fix lowcomms_connect_node for sctp

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  Revert "x86: linker script syntax nits"
  x86, perf_event: Rename 'performance counter interrupt'

The destination keyring specified to request_key() and co. is made available to
the process that instantiates the key (the slave process started by
/sbin/request-key typically).  This is passed in the request_key_auth struct as
the dest_keyring member.

keyctl_instantiate_key and keyctl_negate_key() call get_instantiation_keyring()
to get the keyring to attach the newly constructed key to at the end of
instantiation.  This may be given a specific keyring into which a link will be
made later, or it may be asked to find the keyring passed to request_key().  In
the former case, it returns a keyring with the refcount incremented by
lookup_user_key(); in the latter case, it returns the keyring from the
request_key_auth struct - and does _not_ increment the refcount.

The latter case will eventually result in an oops when the keyring prematurely
runs out of references and gets destroyed.  The effect may take some time to
show up as the key is destroyed lazily.

To fix this, the keyring returned by get_instantiation_keyring() must always
have its refcount incremented, no matter where it comes from.

This can be tested by setting /etc/request-key.conf to:

#OP	TYPE	DESCRIPTION	CALLOUT INFO	PROGRAM ARG1 ARG2 ARG3 ...
#======	=======	===============	===============	===============================
create  *	test:*		*		|/bin/false %u %g %d %{user:_display}
negate	*	*		*		/bin/keyctl negate %k 10 @u

and then doing:

	keyctl add user _display aaaaaaaa @u
        while keyctl request2 user test:x test:x @u &&
        keyctl list @u;
        do
                keyctl request2 user test:x test:x @u;
                sleep 31;
                keyctl list @u;
        done

which will oops eventually.  Changing the negate line to have @u rather than
%S at the end is important as that forces the latter case by passing a special
keyring ID rather than an actual keyring ID.
Reported-by: NAlexander Zangerl <az@bond.edu.au>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Tested-by: NAlexander Zangerl <az@bond.edu.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/pci: Fix MODPOST warning
  powerpc/oprofile: Add ppc750 CL as supported by oprofile
  powerpc: warning: allocated section `.data_nosave' not in segment
  powerpc/kgdb: Fix build failure caused by "kgdb.c: unused variable 'acc'"
  powerpc: Fix hypervisor TLB batching
  powerpc/mm: Fix hang accessing top of vmalloc space
  powerpc: Fix memory leak in axon_msi.c
  powerpc/pmac: Fix issues with sleep on some powerbooks
  powerpc64/ftrace: use PACA to retrieve TOC in mod_return_to_handler
  powerpc/ftrace: show real return addresses in modules

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  ACPI button: don't try to use a non-existent lid device
  ACPI: video: Loosen strictness of video bus detection code
  eeepc-laptop: Prevent a panic when disabling RT2860 wireless when associated
  eeepc-laptop: Properly annote eeepc_enable_camera().
  ACPI / PCI: Fix NULL pointer dereference in acpi_get_pci_dev() (rev. 2)
  fujitsu-laptop: address missed led-class ifdef fixup
  ACPI: Kconfig, fix proc aggregator text
  ACPI: add AC/DC notifier

Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
  OMAP2xxx clock: set up clockdomain pointer in struct clk
  OMAP: Fix race condition with autodeps
  omap: McBSP: Fix incorrect receiver stop in omap_mcbsp_stop
  omap: Initialization of SDRC params on Zoom2
  omap: RX-51: Drop I2C-1 speed to 2200
  omap: SDMA: Fixing bug in omap_dma_set_global_params()
  omap: CONFIG_ISP1301_OMAP redefined in Beagle defconfig

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: always pin metadata in discard mode
  Btrfs: enable discard support
  Btrfs: add -o discard option
  Btrfs: properly wait log writers during log sync
  Btrfs: fix possible ENOSPC problems with truncate
  Btrfs: fix btrfs acl #ifdef checks
  Btrfs: streamline tree-log btree block writeout
  Btrfs: avoid tree log commit when there are no changes
  Btrfs: only write one super copy during fsync

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  tty: fix vt_compat_ioctl

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  sysfs: Allow sysfs_notify_dirent to be called from interrupt context.
  sysfs: Allow sysfs_move_dir(..., NULL) again.

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: gadget: Fix EEM driver comments and VID/PID
  usb-storage: Workaround devices with bogus sense size
  USB: ehci: Fix IST boundary checking interval math.
  USB: option: Support for AIRPLUS MCD650 Datacard
  USB: whci-hcd: always do an update after processing a halted qTD
  USB: whci-hcd: handle early deletion of endpoints
  USB: wusb: don't use the stack to read security descriptor
  USB: rename Documentation/ABI/.../sysfs-class-usb_host

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
  Staging: rt2860sta: prevent a panic when disabling when associated
  staging: more sched.h fixes
  Staging: et131x: Fix the add_10bit macro
  Staging: et131x: Correct WRAP bit handling
  staging: Complete sched.h removal from interrupt.h
  Staging: vme: fix sched.h build breakage
  Staging: poch: fix sched.h build breakage
  Staging: b3dfg: fix sched.h build breakage
  Staging: comedi: fix sched.h build breakage
  Staging: iio: Fix missing include <linux/sched.h>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (53 commits)
  vmxnet: fix 2 build problems
  net: add support for STMicroelectronics Ethernet controllers.
  net: ks8851_mll uses mii interfaces
  net/fec_mpc52xx: Fix kernel panic on FEC error
  net: Fix OF platform drivers coldplug/hotplug when compiled as modules
  TI DaVinci EMAC: Clear statistics register properly.
  r8169: partial support and phy init for the 8168d
  irda/sa1100_ir: check return value of startup hook
  udp: Fix udp_poll() and ioctl()
  WAN: fix Cisco HDLC handshaking.
  tcp: fix tcp_defer_accept to consider the timeout
  3c574_cs: spin_lock the set_multicast_list function
  net: Teach pegasus driver to ignore bluetoother adapters with clashing Vendor:Product IDs
  netxen: fix pci bar mapping
  ethoc: fix warning from 32bit build
  libertas: fix build
  net: VMware virtual Ethernet NIC driver: vmxnet3
  net: Fix IXP 2000 network driver building.
  libertas: fix build
  mac80211: document ieee80211_rx() context requirement
  ...

* branch 'tty-fixes'
  tty: use the new 'flush_delayed_work()' helper to do ldisc flush
  workqueue: add 'flush_delayed_work()' to run and wait for delayed work
  tty: Make flush_to_ldisc() locking more robust

The 2.6.32 merge window brought a number of changes to the flexible array
API; this patch updates the documentation to match the new state of
affairs.
Acked-by: NDavid Rientjes <rientjes@google.com>
Signed-off-by: NJonathan Corbet <corbet@lwn.net>

This reverts commit e9a63a4e.

This breaks older binutils, where sink-less asserts are broken.

See this commit for further details:

  d2ba8b21: x86: Fix assert syntax in vmlinux.lds.S
Acked-by: N"H. Peter Anvin" <hpa@zytor.com>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <4AD6523D.5030909@zytor.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Merge reason: pull in latest, to be able to revert a patch there.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

vmxnet3 uses in_dev* interfaces so it should depend on INET.
Also fix so that the driver builds when CONFIG_PCI_MSI is disabled.

vmxnet3_drv.c:(.text+0x2a88cb): undefined reference to `in_dev_finish_destroy'

drivers/net/vmxnet3/vmxnet3_drv.c:1335: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
drivers/net/vmxnet3/vmxnet3_drv.c:1384: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
drivers/net/vmxnet3/vmxnet3_drv.c:2137: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
drivers/net/vmxnet3/vmxnet3_drv.c:2138: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NBhavesh davda <bhavesh@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Call compat_unimap_ioctl, not do_unimap_ioctl.

This was broken by commit e9216651.

The compat_unimap_ioctl was originally called do_unimap_ioctl in
fs/compat_ioctl.h which got moved to drivers/char/vt_ioctl.c.
In that patch, the caller was not updated and consequently called
the native handler.
Signed-off-by: NAndreas Schwab <schwab@linux-m68k.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

clock24xx.c is missing a omap2_init_clk_clkdm() in its
omap2_clk_init() function.  Among other bad effects, this causes the
OMAP hwmod layer to oops on boot.

Thanks to Carlos Aguiar <carlos.aguiar@indt.org.br> and Stefano
Panella <Stefano.Panella@csr.com> for reporting this bug.  Thanks to Tony
Lindgren <tony@atomide.com> for N800 booting advice.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Carlos Aguiar <carlos.aguiar@indt.org.br>
Cc: Stefano Panella <Stefano.Panella@csr.com>
Cc: Tony Lindgren <tony@atomide.com>

There is a possible race condition in clockdomain
code handling hw supported idle transitions.

When multiple autodeps dependencies are being added
or removed, a transition of still remaining dependent
powerdomain can result in false readings of the
state counter. This is especially fatal for off mode
state counter, as it could result in a driver not
noticing a context loss.

Fixed by disabling hw supported state transitions
when autodeps are being changed.
Signed-off-by: NKalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: sbp2: provide fallback if mgt_ORB_timeout is missing
  ieee1394: add documentation entry to MAINTAINERS
  ieee1394: update URLs in debugging-via-ohci1394.txt

* branch 'tty-fixes':
  tty: use the new 'flush_delayed_work()' helper to do ldisc flush
  workqueue: add 'flush_delayed_work()' to run and wait for delayed work
  Make flush_to_ldisc properly handle parallel calls

Merge branch 'topic/x86-lds-nits' of git://git.kernel.org/pub/scm/linux/kernel/git/frob/linux-2.6-roland

* 'topic/x86-lds-nits' of git://git.kernel.org/pub/scm/linux/kernel/git/frob/linux-2.6-roland:
  x86: linker script syntax nits

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  watchdog: Fix rio watchdog probe function
  sparc64: Set IRQF_DISABLED on LDC channel IRQs.
  sparc64: Fix D-cache flushing on swapin from SW devices.
  sparc64: Fix niagara2 perf IRQ bits.