Under my 2.6.28-rc6 sparc64, when associating to an AP through my
zd1211rw device, I was seeing kernel log messages like (not exact output):

  Kernel unaligned access at TPC[10129b68] zd_mac_rx+0x144/0x32c [zd1211rw]

For the zd1211rw module, on RX, the 80211 packet will be located after
the PLCP header in the skb data buffer. The PLCP header being 5 bytes
long, the 80211 header will start unaligned from an aligned skb
buffer.

As per Documentation/unaligned-memory-access.txt, we must replace the
not unaligned() safe compare_ether_addr() with memcmp() to protect
architectures that require alignment.
Signed-off-by: NShaddy Baddah <shaddy_baddah@hotmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After fixing zd1211rw: use unaligned safe memcmp() in-place of
compare_ether_addr(), I started to see kernel log messages detailing
unaligned access:

  Kernel unaligned access at TPC[100f7f44] sta_info_get+0x24/0x68 [mac80211]

As with the aforementioned patch, the unaligned access was eminating
from a compare_ether_addr() call. Concerned that whilst it was safe to
assume that unalignment was the norm for the zd1211rw, and take
preventative measures, it may not be the case or acceptable to use the
easy fix of changing the call to memcmp().

My research however indicated that it was OK to do this, as there are
a few instances where memcmp() is the preferred mechanism for doing
mac address comparisons throughout the module.
Signed-off-by: NShaddy Baddah <shaddy_baddah@hotmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In "ipw2200: Call netif_*_queue() interfaces properly", netif_stop_queue()
and netif_wake_queue() were removed with the reason
"netif_carrier_{on,off}() handles starting and stopping packet flow into
the driver". The patch also removes a valid condition check that
ipw_tx_skb() cannot be called if device is not in STATUS_ASSOCIATED state.
But netif_carrier_off() doesn't guarantee netdev->hard_start_xmit won't
be called because linkwatch event is handled in a delayed workqueue. This
caused a kernel oops reported by Frank Seidel:
https://bugzilla.novell.com/show_bug.cgi?id=397390

This patch fixes the problem by moving the STATUS_ASSOCIATED check back
to ipw_tx_skb(). It also adds a missing netif_carrier_off() call to
ipw_disassociate().
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NChatre, Reinette <reinette.chatre@intel.com>
Tested-by: NFrank Seidel <fseidel@suse.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch cleans uCode key table bit map iwl_clear_stations_table
since all stations are cleared also the key table must be.

Since the keys are not removed properly on suspend by mac80211
this may result in exhausting key table on resume leading
to memory corruption during removal

This patch also fixes a memory corruption problem reported in
http://marc.info/?l=linux-wireless&m=122641417231586&w=2 and tracked in
http://bugzilla.kernel.org/show_bug.cgi?id=12040.

When the key is removed a second time the offset is set to 255 - this
index is not valid for the ucode_key_table and corrupts the eeprom pointer
(which is 255 bits from ucode_key_table).
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Reported-by: NCarlos R. Mafra <crmafra2@gmail.com>
Reported-by: NLukas Hejtmanek <xhejtman@ics.muni.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since commit d253eee2 the single CAN
identifier filter lists handle only non-RTR CAN frames.

So we need to omit the check of these filter lists when receiving RTR
CAN frames.
Signed-off-by: NOliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Hugo Dias that it is possible to cause a local denial
of service attack by calling the svc_listen function twice on the same
socket and reading /proc/net/atm/*vc
Signed-off-by: NChas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The spinlock used in the netx-eth driver was never properly initialized.
This was noticed using CONFIG_DEBUG_SPINLOCK=y
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I should have noticed this earlier... :-) The previous solution
to URG+GSO/TSO will cause SACK block tcp_fragment to do zig-zig
patterns, or even worse, a steep downward slope into packet
counting because each skb pcount would be truncated to pcount
of 2 and then the following fragments of the later portion would
restore the window again.

Basically this reverts "tcp: Do not use TSO/GSO when there is
urgent data" (33cf71ce). It also removes some unnecessary code
from tcp_current_mss that didn't work as intented either (could
be that something was changed down the road, or it might have
been broken since the dawn of time) because it only works once
urg is already written while this bug shows up starting from
~64k before the urg point.

The retransmissions already are split to mss sized chunks, so
only new data sending paths need splitting in case they have
a segment otherwise suitable for gso/tso. The actually check
can be improved to be more narrow but since this is late -rc
already, I'll postpone thinking the more fine-grained things.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Packet data read from the RX buffer the when the RSV is at the end of the RX
buffer does not warp around. This causes packet loss, as the actual data is
never read. Fix this by calculating the right packet data location.

Thanks to Shachar Shemesh for suggesting the fix.
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Acked-by: NClaudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ifa_local is assumed to be unsigned long which lead to writing the address
at dev->dev_addr-2 instead of +2

noticed thanks to gcc:

drivers/isdn/hysdn/hysdn_net.c: In function `net_open':
drivers/isdn/hysdn/hysdn_net.c:91: warning: array subscript is below array bounds
Signed-off-by: NPascal Terjan <pterjan@mandriva.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On "/etc/init.d/capiutils stop", this oops happened.

The oops happens on reading /proc/capi/controllers because
capi_ctrl->procinfo is called for the wrongly not unregistered
controller, which points to b1isa_procinfo(), which was removed on
module unload.

b1isa_exit() did not call b1isa_remove() for its controllers because
io[0] == 0 on module unload despite having been 0x340 on module load.

Besides, just removing the controllers that where added on module
load time and not those that were added later via b1isa_add_card() is
wrong too - the place where all added cards are found is isa_dev[].

relevant dmesg lines:

[    0.000000] Linux version 2.6.27.4 (w@shubashi) (gcc version 4.3.2 (Debian 4.3.2-1) ) #3 Thu Oct 30 16:49:03 CET 2008

[   67.403555] CAPI Subsystem Rev 1.1.2.8
[   68.529154] capifs: Rev 1.1.2.3
[   68.563292] capi20: Rev 1.1.2.7: started up with major 68 (middleware+capifs)
[   77.026936] b1: revision 1.1.2.2
[   77.049992] b1isa: revision 1.1.2.3
[   77.722655] kcapi: Controller [001]: b1isa-340 attached
[   77.722671] b1isa: AVM B1 ISA at i/o 0x340, irq 5, revision 255
[   81.272669] b1isa-340: card 1 "B1" ready.
[   81.272683] b1isa-340: card 1 Protocol: DSS1
[   81.272689] b1isa-340: card 1 Linetype: point to multipoint
[   81.272695] b1isa-340: B1-card (3.11-03) now active
[   81.272702] kcapi: card [001] "b1isa-340" ready.

[  153.721281] kcapi: card [001] down.
[  154.151889] BUG: unable to handle kernel paging request at e87af000
[  154.152081] IP: [<e87af000>]
[  154.153292] *pde = 2655b067 *pte = 00000000
[  154.153307] Oops: 0000 [#1]
[  154.153360] Modules linked in: rfcomm l2cap ppdev lp ipt_MASQUERADE tun capi capifs kernelcapi ac battery nfsd exportfs nfs lockd nfs_acl sunrpc sit tunnel4 bridge stp llc ipt_REJECT ipt_LOG xt_tcpudp xt_state iptable_filter iptable_mangle iptable_nat nf_nat nf_conntrack_ipv4 nf_conntrack ip_tables x_tables nls_utf8 isofs nls_base zlib_inflate loop ipv6 netconsole snd_via82xx dvb_usb_dib0700 gameport dib7000p dib7000m dvb_usb snd_ac97_codec ac97_bus dvb_core mt2266 snd_pcm tuner_xc2028 dib3000mc dibx000_common mt2060 dib0070 snd_page_alloc snd_mpu401_uart snd_seq_midi snd_seq_midi_event btusb snd_rawmidi bluetooth snd_seq snd_timer snd_seq_device snd via686a i2c_viapro soundcore i2c_core parport_pc parport button dm_mirror dm_log dm_snapshot floppy sg ohci1394 uhci_hcd ehci_hcd 8139too mii ieee1394 usbcore sr_mod cdrom sd_mod thermal processor fan [last unloaded: b1]
[  154.153360]
[  154.153360] Pid: 4132, comm: capiinit Not tainted (2.6.27.4 #3)
[  154.153360] EIP: 0060:[<e87af000>] EFLAGS: 00010286 CPU: 0
[  154.153360] EIP is at 0xe87af000
[  154.153360] EAX: e6b9ccc8 EBX: e6b9ccc8 ECX: e87a0c67 EDX: e87af000
[  154.153360] ESI: e142bbc0 EDI: e87a56e0 EBP: e0505f0c ESP: e0505ee4
[  154.153360]  DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068
[  154.153360] Process capiinit (pid: 4132, ti=e0504000 task=d1196cf0 task.ti=e0504000)
[  154.153360] Stack: e879f650 00000246 e0505ef4 c01472eb e0505f0c 00000246 e7001780 fffffff4
[  154.153360]        fffffff4 e142bbc0 e0505f48 c01a56c6 00000400 b805e000 d102dc80 e142bbe0
[  154.153360]        00000000 e87a56e0 00000246 e12617ac 00000000 00000000 e1261760 fffffffb
[  154.153360] Call Trace:
[  154.153360]  [<e879f650>] ? controller_show+0x20/0x90 [kernelcapi]
[  154.153360]  [<c01472eb>] ? trace_hardirqs_on+0xb/0x10
[  154.153360]  [<c01a56c6>] ? seq_read+0x126/0x2f0
[  154.153360]  [<c01a55a0>] ? seq_read+0x0/0x2f0
[  154.153360]  [<c01c033c>] ? proc_reg_read+0x5c/0x90
[  154.153360]  [<c0189919>] ? vfs_read+0x99/0x140
[  154.153360]  [<c01c02e0>] ? proc_reg_read+0x0/0x90
[  154.153360]  [<c0189a7d>] ? sys_read+0x3d/0x70
[  154.153360]  [<c0103c3d>] ? sysenter_do_call+0x12/0x35
[  154.153360]  =======================
[  154.153360] Code:  Bad EIP value.
[  154.153360] EIP: [<e87af000>] 0xe87af000 SS:ESP 0068:e0505ee4
[  154.153360] ---[ end trace 23750b6c2862de94 ]---
Signed-off-by: NWilfried Klaebe <linux-kernel@lebenslange-mailadresse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Acked-by: NKarsten Keil <kkeil@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to a wrong safety check in af_can.c it was not possible to filter
for SFF frames with a specific CAN identifier without getting the
same selected CAN identifier from a received EFF frame also.

This fix has a minimum (but user visible) impact on the CAN filter
API and therefore the CAN version is set to a new date.

Indeed the 'old' API is still working as-is. But when now setting
CAN_(EFF|RTR)_FLAG in can_filter.can_mask you might get less traffic
than before - but still the stuff that you expected to get for your
defined filter ...

Thanks to Kurt Van Dijck for pointing at this issue and for the review.
Signed-off-by: NOliver Hartkopp <oliver@hartkopp.net>
Acked-by: NKurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a potential NULL pointer dereference seen when trying to remove a
static label configuration with an invalid address/mask combination.
Signed-off-by: NPaul Moore <paul.moore@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bnx2 chips do not support per MSI vector masking.  On 5706/5708, new MSI
address/data are stored only when the MSI enable bit is toggled.  As a result,
SMP affinity no longer works in the latest kernel.  A more serious problem is
that the driver will no longer receive interrupts when the MSI receiving CPU
goes offline.

The workaround in this patch only addresses the problem of CPU going offline.
When that happens, the driver's timer function will detect that it is making
no forward progress on pending interrupt events and will recover from it.

Eric Dumazet reported the problem.

We also found that if an interrupt is internally asserted while MSI and INTA
are disabled, the chip will end up in the same state after MSI is re-enabled.
The same workaround is needed for this problem. 
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Tested-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After flush the SPD entries, dump the SPD entries will cause kernel painc.

Used the following commands to reproduct:

- echo 'spdflush;' | setkey -c
- echo 'spdadd 3ffe:501:ffff:ff01::/64 3ffe:501:ffff:ff04::/64  any -P out ipsec \
  ah/tunnel/3ffe:501:ffff:ff00:200:ff:fe00:b0b0-3ffe:501:ffff:ff02:200:ff:fe00:a1a1/require;\
  spddump;' | setkey -c
- echo 'spdflush; spddump;' | setkey -c
- echo 'spdadd 3ffe:501:ffff:ff01::/64 3ffe:501:ffff:ff04::/64  any -P out ipsec \
  ah/tunnel/3ffe:501:ffff:ff00:200:ff:fe00:b0b0-3ffe:501:ffff:ff02:200:ff:fe00:a1a1/require;\
  spddump;' | setkey -c

This is because when flush the SPD entries, the SPD entry is not remove
from the list.

This patch fix the problem by remove the SPD entry from the list.
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  [WATCHDOG] hpwdt: Fix kdump when using hpwdt
  [WATCHDOG] hpwdt: set the mapped BIOS address space as executable
  [WATCHDOG] iTCO_wdt: add PCI ID's for ICH9 & ICH10 chipsets
  [WATCHDOG] iTCO_wdt : correct status clearing
  [WATCHDOG] iTCO_wdt : problem with rebooting on new ICH9 based motherboards
  [WATCHDOG] fix mtx1_wdt compilation failure

* 'linux-next' of git://git.infradead.org/ubifs-2.6:
  UBIFS: pre-allocate bulk-read buffer
  UBIFS: do not allocate too much
  UBIFS: do not print scary memory allocation warnings
  UBIFS: allow for gaps when dirtying the LPT
  UBIFS: fix compilation warnings
  MAINTAINERS: change UBI/UBIFS git tree URLs
  UBIFS: endian handling fixes and annotations
  UBIFS: remove printk

* 'kvm-updates/2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
  KVM: MMU: avoid creation of unreachable pages in the shadow
  KVM: ppc: stop leaking host memory on VM exit
  KVM: MMU: fix sync of ptes addressed at owner pagetable
  KVM: ia64: Fix: Use correct calling convention for PAL_VPS_RESUME_HANDLER
  KVM: ia64: Fix incorrect kbuild CFLAGS override
  KVM: VMX: Fix interrupt loss during race with NMI
  KVM: s390: Fix problem state handling in guest sigp handler

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Fix offset calculation in compute_size()
  rtc: rtc-starfire fixes

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits)
  MAINTAINERS: add netdev to ATM
  ATM: horizon, fix hrz_probe fail path
  pppol2tp: Add missing sock_put() in pppol2tp_release()
  net: Fix soft lockups/OOM issues w/ unix garbage collector
  macvlan: don't broadcast PAUSE frames to macvlan devices
  Phonet: fix oops in phonet_address_del() on non-Phonet device
  netfilter: ctnetlink: fix GFP_KERNEL allocation under spinlock
  sungem: Fix PCS_MIICTRL register write in gem_init_phy().
  net: make skb_truesize_bug() call WARN()
  net: hp-plus uses eip_poll
  net/wireless/reg.c: fix bad WARN_ON in if statement
  ath5k: disable beacon filter when station is not associated
  ath5k: fix Security issue in DebugFS part of ath5k
  ath9k: correct expected max RX buffer size
  ath9k: Fix SW-IOMMU bounce buffer starvation
  mac80211 : Fix setting ad-hoc mode and non-ibss channel
  iwlagn: fix DMA sync
  phylib: Add Vitesse VSC8221 SGMII PHY
  rose: zero length frame filtering in af_rose.c
  bridge: netfilter: fix update_pmtu crash with GRE
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: Update defconfigs for 2.6.28-rc7
  macfb: Do not overflow fb_fix_screeninfo.id

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  alim15x3: fix sparse warning
  ide: remove dead code from drive_is_ready()
  ide: fix build for DEBUG_PM
  ide: respect current DMA setting during resume
  ide: add SAMSUNG SP0822N with firmware WA100-10 to ivb_list[]
  amd74xx: workaround unreliable AltStatus register for nVidia controllers
  ide: fix the ide_release_lock imbalance

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] stex: switch to block timeout
  [SCSI] make scsi_eh_try_stu use block timeout
  [SCSI] megaraid_sas: switch to block timeout
  [SCSI] ibmvscsi: switch to block timeout
  [SCSI] aacraid: switch to block timeout
  [SCSI] zfcp: prevent double decrement on host_busy while being busy
  [SCSI] zfcp: fix deadlock between wq triggered port scan and ERP
  [SCSI] zfcp: eliminate race between validation and locking
  [SCSI] zfcp: verify for correct rport state before scanning for SCSI devs
  [SCSI] zfcp: returning an ERR_PTR where a NULL value is expected
  [SCSI] zfcp: Fix opening of wka ports
  [SCSI] zfcp: fix remote port status check
  [SCSI] fc_transport: fix old bug on bitflag definitions
  [SCSI] Fix hang in starved list processing

This fixes the MN10300 kernel module linking to match the toolchain.  RELA
relocs don't use the value at the location being relocated.  This has been
working because the tools always leave the value at the target location
cleared.
Signed-off-by: NMark Salter <msalter@redhat.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If xpc.ko and gru.ko are both statically linked into the kernel, then
xpc_init() can get called before gru_init() and make a call to one of the
gru's exported functions before the gru has initialized itself. The end
result is a NULL dereference.
Signed-off-by: NDean Nelson <dcn@sgi.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In the CONFIG_SMP case the irq_choose_cpu() code was returning back
a logical cpu id not the physical id.  We were writing that directly
into the HW register.

We need to be calling get_hard_smp_processor_id() so irq_choose_cpu()
always returns a physical cpu id.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Count the insertion of new pages in the statistics used to drive the
pageout scanning code.  This should help the kernel quickly evict
streaming file IO.

We count on the fact that new file pages start on the inactive file LRU
and new anonymous pages start on the active anon list.  This means
streaming file IO will increment the recent scanned file statistic, while
leaving the recent rotated file statistic alone, driving pageout scanning
to the file LRUs.

Pageout activity does its own list manipulation.
Signed-off-by: NRik van Riel <riel@redhat.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Tested-by: NGene Heskett <gene.heskett@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Devices which share the same queue, like floppies and mtd devices, get
registered multiple times in the bdi interface, but bdi accounts only the
last registered device of the devices sharing one queue.

On remove, all earlier registered devices leak, stay around in sysfs, and
cause "duplicate filename" errors if the devices are re-created.

This prevents the creation of multiple bdi interfaces per queue, and the
bdi device will carry the dev_t name of the block device which is the
first one registered, of the pool of devices using the same queue.

[akpm@linux-foundation.org: add a WARN_ON so we know which drivers are misbehaving]
Tested-by: NPeter Korsgaard <jacmet@sunsite.dk>
Acked-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The previous patch from Alan Cox ("nfsd: fix vm overcommit crash",
commit 731572d3) fixed the problem where
knfsd crashes on exported shmemfs objects and strict overcommit is set.

But the patch forgot supporting the case when CONFIG_SECURITY is
disabled.

This patch copies a part of his fix which is mainly for detecting a bug
earlier.
Acked-by: NJames Morris <jmorris@namei.org>
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJunjiro R. Okajima <hooanon05@yahoo.co.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>

Fix this sparse warning:

  drivers/ide/alim15x3.c:594:2: warning: returning void-valued expression
Signed-off-by: NHannes Eder <hannes@hanneseder.net>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

We guarantee 400ns delay at the time of issuing the command.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Also while at it:

* Drop unused arguments from ide_complete_power_step().

* Move DEBUG_PM printk() from ide_end_drive_cmd() to
  ide_complete_power_step().
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Respect current DMA setting during resume, otherwise PIO timings
may get destroyed if host uses shared PIO/MWDMA timings.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Should fix kernel.org bug #10225:
http://bugzilla.kernel.org/show_bug.cgi?id=10225Reported-by: NMatthias B. <haferfrost@web.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: NSergei Shtyltov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

It seems that on some nVidia controllers using AltStatus register
can be unreliable so default to Status register if the PCI device
is in Compatibility Mode.  In order to achieve this:

* Add ide_pci_is_in_compatibility_mode() inline helper to <linux/ide.h>.

* Add IDE_HFLAG_BROKEN_ALTSTATUS host flag and set it in amd74xx host
  driver for nVidia controllers in Compatibility Mode.

* Teach actual_try_to_identify() and drive_is_ready() about the new flag.

This fixes the regression caused by removal of CONFIG_IDEPCI_SHARE_IRQ
config option in 2.6.25 and using AltStatus register unconditionally when
available (kernel.org bugs #11659 and #10216).

[ Moreover for CONFIG_IDEPCI_SHARE_IRQ=y (which is what most people
  and distributions use) it never worked correctly. ]

Thanks to Remy LABENE and Lars Winterfeld for help with debugging the problem.

More info at:
http://bugzilla.kernel.org/show_bug.cgi?id=11659
http://bugzilla.kernel.org/show_bug.cgi?id=10216Reported-by: NRemy LABENE <remy.labene@free.fr>
Tested-by: NRemy LABENE <remy.labene@free.fr>
Tested-by: NLars Winterfeld <lars.winterfeld@tu-ilmenau.de>
Acked-by: NBorislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide_release_lock() spits out lots of:

	ide_release_lock: bug

warnings on Atari Falcon.

Fix the ide_release_lock imbalance.
Signed-off-by: NMichael Schmitz <schmitz@biophys.uni-duesseldorf.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Don't overflow the 16-character fb_fix_screeninfo id string (fixes some 
console erasing and blanking artifacts). Have the ID default to "Unknown" 
on machines with no built-in video and no nubus devices. Check for 
fb_alloc_cmap failure.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>