- 06 8月, 2018 11 次提交
-
-
由 Vasundhara Volam 提交于
Export temperature sensor reading via hwmon sysfs. Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Use latest firmware API to notify firmware about IF state changes. Firmware has the option to clean up resources during IF down and to require the driver to reserve resources again during IF up. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The flags field is almost getting full. Move firmware capability flags to a new fw_cap field to better organize these firmware flags. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The BNXT_FLAG_NEW_RM flag is checked a lot in the code to determine if the new resource manager is in effect. Define a macro to perform this check. Signed-off-by: NMichael Chan <michael.chan@broadocm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vasundhara Volam 提交于
Add support to collect live firmware coredump via ethtool. Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Set the default hash mode flag in HWRM_VNIC_RSS_CFG to signal to the firmware that the driver is compliant with the latest spec. With that, the firmware can return expanded RSS profile IDs that the driver checks to setup the proper gso_type for GRO-HW packets. But instead of checking for the new profile IDs, we check the IP_TYPE flag in TPA_START which is more straight forward than checking a list of profile IDs. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The new mode is "minimal-static" to be used when resources are more limited to support a large number of VFs, for example The PF driver will provision guaranteed minimum resources of 0. Each VF has no guranteed resources until it tries to reserve resources during device open. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
During hotplug, the driver's open function can be called almost immediately after power on reset. The PHY may not be ready and the firmware may return failure when the driver tries to update PHY settings. Add retry logic fired from the driver's timer to retry the operation for 5 seconds. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Add code to detect firmware support for external loopback and the extra test entry for external loopback. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The driver gathers statistics using 2 mechanisms. Some stats are DMA'ed directly from hardware and others are polled from the driver's timer. Currently, we only adjust the DMA frequency based on the ethtool stats-block-usecs setting. This patch adjusts the driver's timer frequency as well to make everything consistent. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
New interface has firmware core dump support, new extended port statistics, and IF state change notifications to the firmware. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 04 8月, 2018 1 次提交
-
-
由 YueHaibing 提交于
The else-if branch and else branch set mac_ok to true similarly, so combine the two into single else branch. Also add comments to explain the two conditions, which from Michael Chan and Vasundhara Volam. Signed-off-by: NYueHaibing <yuehaibing@huawei.com> Acked-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 17 7月, 2018 1 次提交
-
-
由 YueHaibing 提交于
hwrm_dbg_resp_addr and hwrm_dbg_resp_dma_addr are never used and can be removed. Signed-off-by: NYueHaibing <yuehaibing@huawei.com> Acked-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 14 7月, 2018 1 次提交
-
-
由 Jakub Kicinski 提交于
prog_attached of struct netdev_bpf should have been superseded by simply setting prog_id long time ago, but we kept it around to allow offloading drivers to communicate attachment mode (drv vs hw). Subsequently drivers were also allowed to report back attachment flags (prog_flags), and since nowadays only programs attached will XDP_FLAGS_HW_MODE can get offloaded, we can tell the attachment mode from the flags driver reports. Remove prog_attached member. Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com> Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
-
- 10 7月, 2018 6 次提交
-
-
由 Vikas Gupta 提交于
Fix bug in the error code path when bnxt_request_irq() returns failure. bnxt_disable_napi() should not be called in this error path because NAPI has not been enabled yet. Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.") Signed-off-by: NVikas Gupta <vikas.gupta@broadcom.com> Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Calling bnxt_set_max_func_irqs() to modify the max IRQ count requested or freed by the RDMA driver is flawed. The max IRQ count is checked when re-initializing the IRQ vectors and this can happen multiple times during ifup or ethtool -L. If the max IRQ is reduced and the RDMA driver is operational, we may not initailize IRQs correctly. This problem shows up on VFs with very small number of MSIX. There is no other logic that relies on the IRQ count excluding the ones used by RDMA. So we fix it by just removing the call to subtract or add the IRQs used by RDMA. Fixes: a588e458 ("bnxt_en: Add interface to support RDMA driver.") Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Currently, the driver assumes IFF_BROADCAST is always set and always sets the broadcast filter. Modify the code to set or clear the broadcast filter according to the IFF_BROADCAST flag. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The current code returns -ENOMEM and does not bother to set the output parameters to 0 when no rings are available. Some callers, such as bnxt_get_channels() will display garbage ring numbers when that happens. Fix it by always setting the output parameters. Fixes: 6e6c5a57 ("bnxt_en: Modify bnxt_get_max_rings() to support shared or non shared rings.") Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
If there aren't enough RX rings available, the driver will attempt to use a single RX ring without the aggregation ring. If that also fails, the BNXT_FLAG_AGG_RINGS flag is cleared but the other ring parameters are not set consistently to reflect that. If more RX rings become available at the next open, the RX rings will be in an inconsistent state and may crash when freeing the RX rings. Fix it by restoring the BNXT_FLAG_AGG_RINGS if not enough RX rings are available to run without aggregation rings. Fixes: bdbd1eb5 ("bnxt_en: Handle no aggregation ring gracefully.") Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Venkat Duvvuru 提交于
It is possible that OVS may set don’t care for DEI/CFI bit in vlan_tci mask. Hence, checking for vlan_tci exact match will endup in a vlan flow rejection. This patch fixes the problem by checking for vlan_pcp and vid separately, instead of checking for the entire vlan_tci. Fixes: e85a9be9 (bnxt_en: do not allow wildcard matches for L2 flows) Signed-off-by: NVenkat Duvvuru <venkatkumar.duvvuru@broadcom.com> Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 05 7月, 2018 1 次提交
-
-
由 Vasundhara Volam 提交于
Create initial devlink parameters table for bnxt_en. Table consists of a permanent generic parameter. enable_sriov - Enables Single-Root Input/Output Virtualization(SR-IOV) characteristic of the device. Reviewed-by: NJiri Pirko <jiri@mellanox.com> Reviewed-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 30 6月, 2018 1 次提交
-
-
由 Gustavo A. R. Silva 提交于
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 26 6月, 2018 1 次提交
-
-
由 John Hurley 提交于
Pass the extact struct from a tc qdisc add to the block bind function and, in turn, to the setup_tc ndo of binding device via the tc_block_offload struct. Pass this back to any block callback registrations to allow netlink logging of fails in the bind process. Signed-off-by: NJohn Hurley <john.hurley@netronome.com> Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com> Acked-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 25 6月, 2018 1 次提交
-
-
由 Jiri Pirko 提交于
Currently the default case is not handled, which with future command introductions would introduce a warning. So handle it and make the switch a bit simplier removing unneeded "rc" variable. Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 13 6月, 2018 1 次提交
-
-
由 Kees Cook 提交于
The kmalloc() function has a 2-factor argument form, kmalloc_array(). This patch replaces cases of: kmalloc(a * b, gfp) with: kmalloc_array(a * b, gfp) as well as handling cases of: kmalloc(a * b * c, gfp) with: kmalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kmalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kmalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The tools/ directory was manually excluded, since it has its own implementation of kmalloc(). The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kmalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kmalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kmalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(u8) * COUNT + COUNT , ...) | kmalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kmalloc( - sizeof(char) * COUNT + COUNT , ...) | kmalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kmalloc + kmalloc_array ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kmalloc + kmalloc_array ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kmalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kmalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kmalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kmalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kmalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kmalloc(C1 * C2 * C3, ...) | kmalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kmalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kmalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kmalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kmalloc(sizeof(THING) * C2, ...) | kmalloc(sizeof(TYPE) * C2, ...) | kmalloc(C1 * C2 * C3, ...) | kmalloc(C1 * C2, ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - (E1) * E2 + E1, E2 , ...) | - kmalloc + kmalloc_array ( - (E1) * (E2) + E1, E2 , ...) | - kmalloc + kmalloc_array ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: NKees Cook <keescook@chromium.org>
-
- 26 5月, 2018 1 次提交
-
-
由 Bjorn Helgaas 提交于
Previously the driver used pcie_get_minimum_link() to warn when the NIC is in a slot that can't supply as much bandwidth as the NIC could use. pcie_get_minimum_link() can be misleading because it finds the slowest link and the narrowest link (which may be different links) without considering the total bandwidth of each link. For a path with a 16 GT/s x1 link and a 2.5 GT/s x16 link, it returns 2.5 GT/s x1, which corresponds to 250 MB/s of bandwidth, not the true available bandwidth of about 1969 MB/s for a 16 GT/s x1 link. Use pcie_print_link_status() to report PCIe link speed and possible limitations instead of implementing this in the driver itself. This finds the slowest link in the path to the device by computing the total bandwidth of each link and compares that with the capabilities of the device. The dmesg change is: - PCIe: Speed %s Width x%d + %u.%03u Gb/s available PCIe bandwidth (%s x%d link) Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
-
- 08 5月, 2018 4 次提交
-
-
由 Michael Chan 提交于
The current code already forwards the VF MAC address to the PF, except in one case. If the VF driver gets a valid MAC address from the firmware during probe time, it will not forward the MAC address to the PF, incorrectly assuming that the PF already knows the MAC address. This causes "ip link show" to show zero VF MAC addresses for this case. This assumption is not correct. Newer firmware remembers the VF MAC address last used by the VF and provides it to the VF driver during probe. So we need to always forward the VF MAC address to the PF. The forwarded MAC address may now be the PF assigned MAC address and so we need to make sure we approve it for this case. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vasundhara Volam 提交于
For SFP+ modules, 0xA2 page is available only when Diagnostic Monitoring Type [Address A0h, Byte 92] is implemented. Extend bnxt_get_module_info(), to read optical diagnostics support at offset 92(0x5c) and set eeprom_len length to ETH_MODULE_SFF_8436_LEN (to exclude A2 page), if dianostics is not supported. Also in bnxt_get_module_info(), module id is read from offset 0x5e which is not correct. It was working by accident, as offset was not effective without setting enables flag in the firmware request. SFP module id is present at location 0. Fix this by removing the offset and read it from location 0. Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Only non-NPAR PFs need to actively check and manage unsupported link speeds. NPAR functions and VFs do not control the link speed and should skip the unsupported speed detection logic, to avoid warning messages from firmware rejecting the unsupported firmware calls. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
A recent change to reduce delay granularity waiting for firmware reponse has caused a regression. With a tighter delay loop, the driver may see the beginning part of the response faster. The original 5 usec delay to wait for the rest of the message is not long enough and some messages are detected as invalid. Increase the maximum wait time from 5 usec to 20 usec. Also, fix the debug message that shows the total delay time for the response when the message times out. With the new logic, the delay time is not fixed per iteration of the loop, so we define a macro to show the total delay time. Fixes: 9751e8e7 ("bnxt_en: reduce timeout on initial HWRM calls") Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 28 4月, 2018 10 次提交
-
-
由 Michael Chan 提交于
Add logic to reserve default rings at driver open time if none was reserved during probe time. This will happen when the PF driver did not provision minimum rings to the VF, due to more limited resources. Driver open will only succeed if some minimum rings can be reserved. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
For completeness and correctness, the VF driver needs to reserve these RSS and L2 contexts. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
When rings are more limited and the PF has not provisioned minimum guaranteed rings to the VF, do not reserve rings during driver probe. Wait till device open before reserving rings when they will be used. Device open will succeed if some minimum rings can be successfully reserved and allocated. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The current code does not reserve rings during ethtool -L when the device is down. The rings will be reserved when the device is later opened. Change it to reserve rings during ethtool -L when the device is down. This provides a better guarantee that the device open will be successful when the rings are reserved ahead of time. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andy Gospodarek 提交于
This adds debugfs support for bnxt_en with the purpose of allowing users to examine the current DIM profile in use for each receive queue. This was instrumental in debugging issues found with DIM and ensuring that the profiles we expect to use are the profiles being used. Signed-off-by: NAndy Gospodarek <gospo@broadcom.com> Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andy Gospodarek 提交于
Testing with DIM enabled on older kernels indicated that firmware calls were slower than expected. More detailed analysis indicated that the default 25us delay was higher than necessary. Reducing the time spend in usleep_range() for the first several calls would reduce the overall latency of firmware calls on newer Intel processors. Signed-off-by: NAndy Gospodarek <gospo@broadcom.com> Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andy Gospodarek 提交于
This keeps the RING_IDLE flag set in hardware for higher coalesce settings by default and improved latency. Signed-off-by: NAndy Gospodarek <gospo@broadcom.com> Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Firmware does not allow the operation and would return failure, causing a warning in dmesg. So check for VF and disallow it in the driver. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vasundhara Volam 提交于
Add counters to display sum of rx/tx_discard_pkts of all rings as function level statistics via ethtool. Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Replace switch statements printing different messages for every ring type with a common message. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-