RX is handled in a workqueue therefore allocating for GFP_ATOMIC
is overkill and not required.

Based on a patch for wl1271 by Luis R. Rodriguez.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The wakeup time calculation was too complicated, simplify it.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The original TI driver uses 100 ms timeout ELP wakeup timeout, better
to use the same. Otherwise problems with wakeup might get unnoticed.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Not all return values were checked and one exit from function didn't put
firmware sleep after the error.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This debug message was missing and caused incomplete log messages.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sometimes when debugging the state is good info.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This hack was totally wrong and was "needed" because of a problem in the way
we were sending the GENERAL_PARMS command to the firmware.  Now that that
problem has been fixed, this hack can be removed.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We were ignoring the -EIO return value from wl1271_cmd_radio_params() and
wl1271_cmd_general_params(), because they were always returning an error and
we didn't know why.  Now this has been fixed, so the workaround can be
removed.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We were missing the command header in the radio and general parameters
commands.  This was causing them to fail, resulting in problems in the power
levels and other PLT-related commands.

Also reorganized the command functions, moving from wl1271_init.c to
wl1271_cmd.c where it fits better.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We need to set the radio and general parameters when starting PLT mode.  This
patch adds calls to TEST_CMD_INI_RADIO_PARAMS and
TEST_CMD_INIT_GENERAL_PARAMS when initializing PLT mode.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The wl1271_dev_notify() was returning 0 or -ENODEV, when it should return
NOTIFY_* instead.  Now we use NOTIFY_DONE when we didn't handle the event or
NOTIFY_OK when we have handled it.

For inetdev notifications, it doesn't matter whether we use NOTIFY_DONE or
NOTIFY_OK, because it ignores the return value of the call to
blocking_notifier_call_chain().  But the notify.h header says that
NOTIFY_DONE is "Don't care" and NOTIFY_OK is "Suits me", so that seems to be
the right way to do it.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Set the PSM support flag in the device configuration
for the mac80211 stack. This will enable usage of powersave.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Prevent endless PSM-entry retry loops, if PSM has already been cancelled while
PSM entry was attempted.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Decrease the consecutive terminated beacons value for BET from 100 to 10.
According to the vendor, 10 will give a more reliable connection and more
reliable detection of connection problems.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

wl1251 supports also that NVS is stored in a separate EEPROM, add support
for that.

kvalo: use platform data instead Kconfig and use kernel style
Signed-off-by: NDavid-John Willis <John.Willis@Distant-earth.com>
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixes warnings:

drivers/net/wireless/wl12xx/wl1251_rx.c: In function 'wl1251_rx_status':
drivers/net/wireless/wl12xx/wl1251_rx.c:75:
  warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
drivers/net/wireless/wl12xx/wl1251_rx.c:77:
  warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
drivers/net/wireless/wl12xx/wl1251_rx.c:77:
  warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
drivers/net/wireless/wl12xx/wl1251_rx.c:77:
  warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
drivers/net/wireless/wl12xx/wl1251_rx.c:78:
  warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
drivers/net/wireless/wl12xx/wl1251_rx.c:78:
  warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
drivers/net/wireless/wl12xx/wl1251_rx.c:78:
  warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

According to IEEE80211 standard all the data packets have to be sent with
TODS bit set. This patch fixes the null data packet format which was sent
without TODS bit set. This should fix many problems associated with
power save. Janne Ylalehto also found this fix in the same time as mine,
for a different bug he was working on.
Signed-off-by: NVidhya Govindan <vidhya.govindan@nokia.com>
Reviewed-by: NJanne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In some cases, the IRQ loop handler could acknowledge an interrupt to
the chipset, but not service it.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NJanne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Filter out unwanted events to reduce wakeups.
Signed-off-by: NJanne Ylalehto <janne.ylalehto@nokia.com>
Reviewed-by: NVidhya Govindan <vidhya.govindan@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for IRQ looping. Helps in the case that we have e.g. multiple
packets coming from the network when we wake up from the ELP.
Signed-off-by: NJanne Ylalehto <janne.ylalehto@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch increases the number of beacons to be missed before generating
SYNC TIMEOUT event. It increases the beacon timeout period to 500
microseconds, which gives enough time for the firmware to receive probe
response or beacon. Also handled the regain event from firmware once it
receives a probe response or beacon.
Signed-off-by: NVidhya Govindan <vidhya.govindan@nokia.com>
Reviewed-by: NJanne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch sets the dtim period obtained from the mac80211 to firmware.
Signed-off-by: NVidhya Govindan <vidhya.govindan@nokia.com>
Reviewed-by: NJanne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The dtim period obtained from the mac80211 is not set to the firmware.
This patch implements the acx command to set correct tbtt and dtim value
to the firmware.
Signed-off-by: NVidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Reviewed-by: NJanne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In ps-poll template aid bits 14 and 15 were not masked as required by the
standard. Mask them so that aid is sent in correct format.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NVidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Earlier firmware was stored to a memory area allocated with kmalloc()
but finding a a contiguous area of memory long enough for the firmware is
very difficult in certain cases. better to allocate the memory for firmware
with vmalloc() instead and use a small buffer for DMA transfers.

Thanks to Eero Tamminen for the idea.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Reviewed-by: NVidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Implement (slightly) delayed entry into ELP. This will cure several
problems:
  - It works around a firmware race condition if ELP is entered too fast
    after commands (resulting in ELP timeout -traces)
  - It will reduce the number of sleep-wake cycles between already
    scheduled events such as interrupts and tx, hence improving
    performance (less delay in switching between RX and TX)
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NVidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable beacon filtering when PSM is enabled
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable beacon filtering with the mac80211 stack.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add configuration for connection monitor (number of allowed beacons, and
timeout after last received beacon.)
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RX is handled in a workqueue therefore allocating for GFP_ATOMIC
is overkill and not required.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

wl1271_main.c:(.text+0x271052): undefined reference to `unregister_inetaddr_notifier'
wl1271_main.c:(.text+0x2714d7): undefined reference to `register_inetaddr_notifier'

Driver is doing some filtering based on IP addresses...
Acked-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Responses to firmware commands are read in by the command transmission
function, as part of command flow. Previously responses were read in
multiple places.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Correct the endianness-handling of the firmware command result status handling
code.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

PSM entries can fail (transmitting the corresponding null-func may not
be heard by the AP.) Previously, this scenario was not detected, and
out-of-sync between STA and AP could occur.

Add retry implementation for the entries to recover from the situation.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Check the result code of all commands, and return an error code if the
firmware reports an error in execution. Previously this error would go
ignored in most cases.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, to avoid distortions, the TX power level has been hardcoded
to a low value. The value is slightly too low for good functionality, so
we increase it from 7dB to 12dB.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The null-data template (nullfunc) is dependent on the BSSID of the
current AP only, so it needs to be updated only when the BSSID changes.

Removed excess setting of the template.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The check after the loop which checks whether the initialization timed-out
was wrong.  If the initialization would succeed exactly in the 20000th time
(the value set for INIT_LOOP), the driver would bail out and claim that
initialization failed.
Reported-by: NJuha Leppanen <juha_motorsportcom@luukku.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJanne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With the WLAN_PRE80211 drivers moved to drivers/staging, this
distinction becomes unnecessary.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>