There were still some corner cases where isoc transfer was not able to
restart, specially when missed isoc does not happen , and in fact gadget does
not queue any new request during giveback.

Cleanup function calls giveback first, which provides a way to queue
another request to gadget. But gadget did not had any data. So , it did
not call ep_queue. To twist it further, gadget did not queue till
cleanup for last queued TRB is called. If we ever reach this scenario,
we must call END TRANSFER, so that we receive a new  xfernotready with
information about current microframe number.

Also insure that there is no request submitted to core when issuing END
TRANSFER.

Cc: <stable@vger.kernel.org> # v3.8
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Its better to return from each if condition as they are mutually
exclusive.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There are two reasons to generate missed isoc.

1. when the host does not poll for all the data.
2. because of application-side delays that prevent all the data from
being transferred in programmed microframe.

Current code was able to handle first case only.  This patch handles
scenario 2 as well.Scenario 2 sometime may occur with complex gadget
application, however it can be easily reproduced for testing purpose as
follows:

a. use isoc binterval as 1 in f_sourcesink.
b. use pattern=0
c. introduce a delay of 150us deliberately in source_sink_complete, so
that after few frames it lands into scenario 2.
d. now run testusb 16 (isoc in  test). You will notice that if this
patch is not applied then isoc transfer is not able to recover after
first missed.

Current patch's approach is as under:

If missed isoc occurs and there is no request queued then issue END
TRANSFER, so that core generates next xfernotready and we will issue a
fresh START TRANSFER.
If there are still queued request then wait, do not issue either END or
UPDATE TRANSFER, just attach next request in request_list during giveback.
If any future queued request is successfully transferred then we will issue
UPDATE TRANSFER for all request in the request_list.

Cc: <stable@vger.kernel.org> # v3.6 v3.7 v3.8
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Synopsys says:
The HIRD Threshold field must be set to ‘0’ when the device core is
operating in super speed mode.

This patch implements above statement.

Cc: <stable@vger.kernel.org> # v3.6 v3.7 v3.8
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

regset is a generic implementation of regdump
utility through debugfs.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

we have an extra 'ret' variable shadowing a previous
definition. Remove it.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The devm_ functions allocate memory that is released when a driver
detaches. This makes the code smaller and a bit simpler.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Currently we're allocating an entire page to
serve as our event buffer. Provided our events
are 4 bytes long, it's very unlikely we will
even trigger 1k events at once.

Even in the worst case scenario where every
endpoint triggers one event and we still have
a couple of error events, that would still
be less than 40 events.

In order to cope with future versions of the
IP which could (or could not) increase the
amount of possible events to trigger
simultaneously, we're using an arbitrary size
of 64 events for our event buffer.

We're saving 3840 bytes by doing so.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

As with dwc_readl/writel, the global registers are specified as
offsets starting from the beginning of the xHCI address space,
but the memory region pointed to by dwc->regs already maps to
the start of the global addresses. Fix by offsetting each of the
regs relative to DWC3_GLOBALS_REGS_START.
Signed-off-by: NJack Pham <jackp@codeaurora.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 392142 moved event buffer allocation out of dwc3_core_init() but
event buffer allocation uses the cached copy of hwparams to determine
the number of event buffers and the caching is done in dwc3_core_init.
So moved dwc3_cache_hwparams function before dwc3_alloc_event_buffers so
that dwc3_alloc_event_buffers sees the correct number of event buffers.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 380f0d28 (usb: dwc3: core: switch event
buffer allocation to devm_kzalloc()) was incomplete
leaving a trailing kfree(evt) in an error exit
path.

Fix this problem by removing the trailing kfree(evt).

Cc: Julia Lawall <julia.lawall@lip6.fr>
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We are removing plat data which was used till now to init and
exit phy. We no longer need this since dwc3-core takes care of
initializing and shutting-down the phy using usb_phy_init()
and usb_phy_shutdown().
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch adds support to parse probe data for
dwc3-exynos driver using device tree.
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The lockless implementation of the unique id is quite impressive (:P)
but dirver's core can handle it, we can remove it and make our code a
little smaller.

Cc: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

commit 93abe8e4 (clk: add non CONFIG_HAVE_CLK routines)
added clk API stubs when !defined(CONFIG_HAVE_CLK).

This allows us to remove the HAVE_CLK dependency from
Exynos' glue layer and let it compile always.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We call usb_phy_init() from dwc3_core_init() during
probe, so adding usb_phy_shutdown() to dwc3_core_exit()
while removing the device so we don't keep PHYs
turned on, consuming power, unnecessarily.
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If a USB transfer has already been started, meaning
we have already issued StartTransfer command to that
particular endpoint, DWC3_EP_BUSY flag has also
already been set.

When we try to cancel this transfer which is already
in controller's cache, we will not receive XferComplete
event and we must clear DWC3_EP_BUSY in order to allow
subsequent requests to be properly started.

The best place to clear that flag is right after issuing
DWC3_DEPCMD_ENDTRANSFER.

Cc: stable@vger.kernel.org # v3.4 v3.5 v3.6
Reported-by: NMoiz Sonasath <m-sonasath@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch is in preparation for adding PM support
dwc3 driver. We want to re-use dwc3_core_init and
dwc3_core_exit() functions on resume() and suspend()
callbacks respectively.

Moving even buffer allocation away from dwc3_core_init()
will allow us to reuse the event buffer which was allocated
long ago on our probe() routine.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The rest of the driver is using devm_kzalloc() where possible
and this patch is just making event buffer allocation follow
the example.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

this will let us control PHYs on platforms which
need them.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We will be adding support for transceivers on
dwc3 driver but not all boards have controllable
transceivers.

For those which don't provide controllable transceivers
we will register nop transceivers.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We will be adding support for transceivers on
dwc3 driver but not all boards have controllable
transceivers.

For those which don't provide controllable transceivers
we will register nop transceivers.

Note that once OMAP's transceiver drivers reach mainline,
this glue layer will change accordingly.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We will be adding support for transceivers on
dwc3 driver but not all boards have controllable
transceivers.

For those which don't provide controllable transceivers
we will register nop transceivers.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If xfernotready is received and there is no request in request_list then
REQUEST_PENDING flag must be set, so that next request in ep queue is executed.

In case of isoc transfer, if xfernotready is already elapsed and even first
request has not been queued to request_list, then issue END TRANSFER, so that
you can receive xfernotready again and can have notion of current microframe.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Populate the resources for xhci afresh instead of directly using the
*struct resource* of core. *resource* structure has parent, sibling,
child pointers which should be filled only by resource API's. By
directly using the *resource* pointer of core in xhci, these parent,
sibling, child pointers are already populated even before
*platform_device_add* causing side effects.

Cc: stable@vger.kernel.org # v3.4, v3.5
Reported-by: NRuchika Kharwar <ruchika@ti.com>
Tested-by: NMoiz Sonasath <m-sonasath@ti.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In case of ep0 out, if length is not aligned to maxpacket size then we use
dwc->ep_bounce_addr for dma transfer and not request->dma. Since, we have
alreday done memcpy from dwc->ep0_bounce to request->buf, so we do not need to
issue cache sync function. In fact, cache sync function will bring wrong data
in request->buf from request->dma in this scenario.

So, cache sync function must not be executed in case of ep0 bounced.

Cc: <stable@vger.kernel.org> # v3.4 v3.5
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This commit removes USB_GADGET_DUALSPEED and USB_GADGET_SUPERSPEED
Kconfig options.  Since now kernel allows many UDC drivers to be
compiled, those options may turn to no longer be valid.  For
instance, if someone decides to build UDC that supports super
speed and UDC that supports high speed only, the latter will be
"assumed" to support super speed since USB_GADGET_SUPERSPEED will
be selected by the former.

The test of whether CONFIG_USB_GADGET_*SPEED was defined was just
an optimisation which removed otherwise dead code (ie. if UDC is
not dual speed, there is no need to handle cases that can happen
if speed is high).  This commit removes those checks.
Signed-off-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When connection is established non-ss mode, endpoint.maxburst is correctly set
to 0, this means that current code will set maxburst bitfield on DEPCFG's
parameter 0 to the highest possible value (0x0f) which is wrong.

Even though this hasn't caused any issues so far (HW seems to ignore that when
not running in SS mode) we want to make sure maxburst bitfield is only set to
anything other than zero if we're running on SuperSpeed mode. In order to
achieve that, let's check for gadget's operating speed before setting maxburst
bitfield when issuing DEPCFG command.

[ balbi@ti.com : improved commit log a bit in order to clarify the situation ]
Signed-off-by: NChanho Park <chanho61.park@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

As a bitmap is used for free/used. As a device freed
all memory operations must be scheduled before the bitmap
is manipulated.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In case some gadget driver tries to enable an endpoint
which is already enabled, we print a nice WARN so we
can track broken gadget drivers. The only problem is that
we're printing the WARN when we already changed endpoint's
name, which would result in endpoints named as:

ep1in-bulk-bulk-bulk-bulk-bulk-bulk-bulk

To prevent that, we will continue to print the WARN,
but do so before changing endpoint's name and return
early.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This just guarantees that this piece of memory
will be marked uncachable.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

dwc3_stop_active_transfer has been called from two places. After each
calling of this function , we should allow 100 us delay to synchronize
with interconnect.

It would be better if we put this delay in that function only, rather
than into calling routine of this function.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Reported-by: NMichel Sanches <michel.sanches@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When MISSED_ISOC is set, BUSY is also set. Since, we are handling
MISSED_ISOC as a separate case in third scenario, therefore handle only
BUSY but not MISSED_ISOC in second scenario.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch fixes the following sparse warnings:

drivers/usb/dwc3/gadget.c:1096:7: warning: symbol 'ret' shadows an earlier one
drivers/usb/dwc3/gadget.c:1058:8: originally declared here
drivers/usb/dwc3/gadget.c:1100:16: warning: symbol 'dwc' shadows an earlier one
drivers/usb/dwc3/gadget.c:1057:15: originally declared here
drivers/usb/dwc3/gadget.c:1118:16: warning: symbol 'dwc' shadows an earlier one
drivers/usb/dwc3/gadget.c:1057:15: originally declared here
drivers/usb/dwc3/gadget.c:1800:19: warning: symbol 'dep' shadows an earlier one
drivers/usb/dwc3/gadget.c:1778:18: originally declared here

Also, fix the potential checkpatch errors around the if() loops that
this fix patch can create.
Signed-off-by: NMoiz Sonasath <m-sonasath@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When issuing SetStall on ep0, we must make sure to
reinitialize all flags on physical ep1 too.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

commit 68d3e668 (usb: dwc3: ep0: fix for possible early
delayed_status) added handling for early delayed status,
but the current code only works because so far delayed
status will always be on the IN direction.

This patch makes the code more robust by making sure that
we can handle all directions properly.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Due to the late Silicon limitation found, we are
now pre-starting DATA phase's TRBs. If, still, we
get XferNotReady(DATA) we will ignore it unless
we're getting it for the wrong direction.

In that case we must keep the error case handling
plus add a ENDTRANSFER command to forcefully end
the Data TRB we started previously, then continue
to SetStall and so on.
Signed-off-by: NFelipe Balbi <balbi@ti.com>