o Update the port type information
o Advertise correct link modes and autonegotiation
o Add support to change link speed
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Leftover from 6e1d0b89 ("r8169:add
support for RTL8168H and RTL8107E").
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mirror the changes made to ixgbe in commit 2367a173
("ixgbe: flush when in xmit_more mode and under descriptor pressure")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mirror the changes made to ixgbe in commit 2367a173
("ixgbe: flush when in xmit_more mode and under descriptor pressure")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When xmit_more mode is being used and the ring is about to
become full or the stack has stopped the ring, enforce a tail
pointer write to the hw. Otherwise, we could risk a TX hang.

Code suggested by Alexander Duyck.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add two new entries to the Broadcom BCM7xxx internal PHY driver for
BCM7250 and BCM7364 chips. Those chips share the usual 28nm process
Gigabit PHY sequence and require the same workarounds so far.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All 28nm Gigabit PHYs supported by the driver have the same
callbacks, the only differences being the 32-bits OUI and the name. Use
a macro to factor this, making it easier in the future to add new
entries.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sungem driver has "phy_read()" and "phy_write()" functions, which
we need to rename because the generic phy layer is about to export
generic interfaces with the same name.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the Broadcom Starfigther 2 switch chip using a DSA
driver. This switch driver supports the following features:

- configuration of the external switch port interface: MII, RevMII,
  RGMII and RGMII_NO_ID are supported
- support for the per-port MIB counters
- support for link interrupts for special ports (e.g: MoCA)
- powering up/down of switch memories to conserve power when ports are
  unused

Finally, update the compatible property for the DSA core code to match
our switch top-level compatible node.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a generic UniMAC MDIO bus driver and its Device Tree binding, which
can be used by the BCMGENET driver as-is, and the upcoming Starfighter 2
Ethernet switch MDIO bus controller.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sungem driver has "phy_read()" and "phy_write()" functions, which
we need to rename because the generic phy layer is about to export
generic interfaces with the same name.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dmfe driver has "phy_read()" and "phy_write()" functions, which
we need to rename because the generic phy layer is about to export
generic interfaces with the same name.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some platforms have special bank registers which might be used to
select the correct clock or the right mode for Media Indepent Interface
controllers. Sometimes, it is also required to activate vcc regulators
in the right order to supply the ethernet controller at the right time.
This patch is an architecture refactoring of the arc-emac device driver.
It adds a new software design which allows to add specific platform
glue layer. Each platform has now its own module which performs custom
initialization and remove for the target and then calls to the
core driver.
Signed-off-by: NRomain Perier <romain.perier@gmail.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is an api changes for the emac_mdio.c module.
It will be required later when arc_emac_probe/arc_emac_remove
will no longer use 'struct platform_device'.
Signed-off-by: NRomain Perier <romain.perier@gmail.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a preparation of an api changes for the emac_main.c module.
The involved functions are arc_emac_probe and arc_emac_remove.
Signed-off-by: NRomain Perier <romain.perier@gmail.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Incorrect checking of array instead of array contents in panic_dump
flow - results of commit e2611998 ("bnx2x: Safe bnx2x_panic_dump()").
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the strncpy with strlcpy, and use sizeof to determine the
length.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bump versions for i40e to 1.0.4 and i40evf to 1.0.1.

Change-ID: I960c04da2c91bdf1d02f8e5011e68c34a634122d
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-By: NJim Young <jamesx.m.young@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We are seeing situations where the driver sees a hang with less than 4
desc pending, if the driver chooses to ignore it the queue progresses
forward and the stack never experiences a real hang.
With this patch we will log a stat when this situation happens
"tx_sluggish" will increment and we can see some more details
at a higher debug level. Other than that we will ignore this
particular case of Tx hang.

Change-ID: I7d1d1666d990e2b12f4f6bed0d17d22e1b6410d5
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Older firmware has an incorrect MAC VLAN filter that needs to be replaced
at startup, and now newer firmware doesn't have this problem.  With this
change we no longer complain if the remove fails, and we only add the
new filter if the remove succeeded.

Setting a new LAA worked the first time, but didn't work well in successive
operations, including returning to the HW default address.  This simplifies
the code that was trying to be too smart.

Lastly, this pulls the hardware default mac address out into separate
handling code and keeps the broadcast filtering from getting munged.

Change-ID: I1f54b002def04ffef2546febb9a4044385452f85
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There is at least one case in the Firmware API where the response to a
command changes the buffer size field in the AQ descriptor to a larger
number than what the request's buffer size started as.  This is in addition
to setting an error flag and is in order to tell the requester how much
larger a buffer is required for the answer.  We need to be sure not to
use that number when dumping the contents of the data buffer because it
can send us into the weeds and generate an invalid pointer exception.

This patch adds a max buffer size parameter to the print helper to be
sure the code knows when to stop.

Change-ID: Ib84f7ed72140fe9d600086d8f2002fc5d8753092
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a check during handle_link_event for unqualified
module when link is down and there is a module plugged.  If found,
print a message.

Change-ID: Ibd8666d77d3044c2a3dd4d762d3ae9ac6e18e943
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Change vsi->num_queue_pairs to equal the number that are configured
by the VF. This, in turn, limits the number of queues that are
enable/disabled. This fixes the mismatched case for when a VF configures
fewer queues than is allocated to it by the PF.

Change other sections to use alloc_queue_pairs as warranted.

Change-ID: I0de1b55c9084e7be6acc818da8569f12128a82c2
Signed-off-by: NAshish Shah <ashish.n.shah@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Enable the l2tsel bit on Rx queue contexts that are assigned to VFs so
that the VF can get the stripped VLAN tag.

Change-ID: I7d9bc56238a9ea9baf5e8a97e69b9e27ebb9d169
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NAshish Shah <ashish.n.shah@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This helps know how many times the interface had to flush and replay FD
filter table, which gives an indication on how often we are getting FD
table full situation.

Also check on certain pf states before proceeding to add or delete
filters since we can't add or delete filters if we are in those states.

Change-ID: I97f5bbbea7146833ea61af0e08ea794fccba1780
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Instead of disabling ATR when we get a programming error, we now
will wait it out to see if some room gets created by ATR rule deletion.
If we still have too many errors and ATR filter count did not change
much, its time to flush and replay. We no more auto-disable ATR when
we have errors in programming.
The disabling of ATR when we get programming error was buggy and
was still adding new rules and causing continuous errors. With this
policy change we flush instead when we see too many errors.
ATR is still disabled if we add a SB rule for TCP/IPv4 flow type,
more logic is added to re-enable it once all SB TCP/IPv4 rules are gone.

Change-ID: I77edcbeab9500c72a7e0bd7b5c5b113ced133a9c
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Change the message that gets printed when adding/deleting a filter to
the SB, so that user can tell if a filter was added or deleted.
Print filter add failures only in case of SB filters. For ATR the
information is not useful to the user and hence suppress it unless in
higher debug mode.

Change-ID: I78d7a7a6ecfa82a38a582b0d7b4da038355e3735
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch changes the wording of the flow director add/remove and
asynchronous failure messages to include fd_id to try and add some
way to track the operations on a given fd_id.  Its not perfect, but
its better than what we had as PCTYPE can apply to several different
filter requests.

This patch also removes a redundant message when filter
addition fails due to full condition.

Change-ID: Icf58b0603d4f162d9fc542f11a74866a907049f2
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

bnx2x uses ptp functions, so it should select the provider of
those functions (PTP_1588_CLOCK).  Fixes these build errors:

drivers/built-in.o: In function `__bnx2x_remove':
/home/jim/linux/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:13409:
undefined reference to `ptp_clock_unregister'
drivers/built-in.o: In function `bnx2x_register_phc':
/home/jim/linux/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:13202:
undefined reference to `ptp_clock_register'
drivers/built-in.o: In function `bnx2x_get_ts_info':
/home/jim/linux/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c:3498:
undefined reference to `ptp_clock_index'
Reported-by: NJim Davis <jim.epost@gmail.com>
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When one tries to add eth as a port into team and that eth is already in
use by other rx_handler device (macvlan, bond, bridge, ...) a bug in
team_port_add() causes that IFF_TEAM_PORT flag is set before rx_handler
is registered. In between, netdev nofifier is called and
team_device_event() sees IFF_TEAM_PORT and thinks that rx_handler_data
pointer is set to team_port. But it isn't.

Fix this by reordering rx_handler register and IFF_TEAM_PORT priv flag
set so it is very similar to how bonding does this.
Reported-by: NErik Hugne <erik.hugne@ericsson.com>
Fixes: 3d249d4c "net: introduce ethernet teaming device"
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit eeed018c ("bnx2x: Add timestamping and PTP hardware clock support")
has a missing conversion to LE32, which will prevent the feature from working
on big endian machines.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This introduces 2 new relaxations in the bnx2x driver regarding GRO:
  1. Don't prevent SW GRO if HW GRO is disabled.
  2. If all aggregations are disabled, when GRO configuration changes
     there's no need to perform an inner-reload [since it will have no
     actual effect].
Signed-off-by: NDmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During statistics initialization of a VF we need to clean its statistics.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When STOP_ON_ERROR is set driver will not compile. Even if it did,
traffic will not pass without this patch as several fields which are
verified by FW/HW on the Tx path are not properly set.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This changes slightly the set of registers read during `ethtool -d'.
Without this change, it's possible the HW will generate a grc Attention which
will be logged into system logs as `grc timeout'.
Signed-off-by: NDmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This implements the deferred tail pointer flush API for the ixgbe
driver. Similar version also proposed longer time ago by Alexander Duyck.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Jesper Dangaard Brouer, for high packet rates the
overhead of having another indirect call in the TX path is
non-trivial.

There is the indirect call itself, and then there is all of the
reloading of the state to refetch the tail pointer value and
then write the device register.

Move to a more passive scheme, which requires very light modifications
to the device drivers.

The signal is a new skb->xmit_more value, if it is non-zero it means
that more SKBs are pending to be transmitted on the same queue as the
current SKB.  And therefore, the driver may elide the tail pointer
update.

Right now skb->xmit_more is always zero.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use is_kdump_kernel() to detect kdump kernel, instead of
reset_devices.

CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds simple cleanups for stmmac, removing test we know is always
true, fixing whitespace, and moving code out of if().
Signed-off-by: NPavel Machek <pavel@denx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

626: CHECK: Alignment should match open parenthesis
 646: CHECK: Alignment should match open parenthesis
 655: CHECK: Alignment should match open parenthesis
 695: CHECK: Alignment should match open parenthesis
 729: CHECK: Alignment should match open parenthesis
 739: CHECK: Alignment should match open parenthesis
 976: WARNING: externs should be avoided in .c files
 1314: CHECK: Alignment should match open parenthesis
 1358: WARNING: networking block comments don't use an empty /* line, use /* Comment...
 1402: WARNING: networking block comments don't use an empty /* line, use /* Comment...
 1521: CHECK: multiple assignments should be avoided
 1775: CHECK: Alignment should match open parenthesis
 1838: CHECK: multiple assignments should be avoided
 1843: CHECK: multiple assignments should be avoided
 1847: CHECK: multiple assignments should be avoided
 1850: WARNING: Missing a blank line after declarations
 1864: CHECK: Alignment should match open parenthesis
 1872: CHECK: braces {} should be used on all arms of this statement
 1906: CHECK: usleep_range is preferred over udelay
 2865: WARNING: networking block comments don't use an empty /* line, use /* Comment...
 3088: CHECK: Alignment should match open parenthesis
 total: 0 errors, 5 warnings, 16 checks, 3567 lines checked
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>