Introduce a private pointer in struct subchannel to store
per-subchannel type data (cannot use dev->priv since this
is already used for something else).

Create a new header io_sch.h for I/O subchannel specific structures
and instructions.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

If I/O was running on a just varied off chpid, it will be terminated.
If this was a common I/O layer internal I/O, it needs to be retried.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Use the proper structures to identify device and subchannel. Change
get_disc_ccwdev_by_devno() to get_disc_ccwdev_by_dev_id().
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

While the machine owns us an interrupt in these cases (and we should get
one), reality isn't always like that...
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Reappearing channel paths are sometimes not utilized by CCW devices
because path verification incorrectly relies on path-operational-mask
information which is not updated until a channel path has been used
again.
Modify path verification procedure to always query all available paths
to a device.
Signed-off-by: NPeter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Calls to set a device online with path grouping may get stuck in
some cases because certain device conditions where discarded after
unsolicited interrupts.
Check subchannel activity after unsolicited interrupts and retry
the operation if the subchannel is idle.
Signed-off-by: NStefan Bader <shbader@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

1. Multipath devices for which SetPGID is not supported are not handled well.
   Use NOP ccws for path verification (sans path grouping) when SetPGID is not
   supported.
2. Check for PGIDs already set with SensePGID on _all_ paths (not just the
   first one) and try to find a common one. Moan if no common PGID can be
   found (and use NOP verification). If no PGIDs have been set, use the css
   global PGID (as before). (Rationale: SetPGID will get a command reject if
   the PGID it tries to set does not match the already set PGID.)
3. Immediately before reboot, issue RESET CHANNEL PATH (rcp) on all chpids. This
   will remove the old PGIDs. rcp will generate solicited CRWs which can be
   savely ignored by the machine check handler (all other actions create
   unsolicited CRWs).
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NJörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

If __ccw_device_disband_start() fails to initiate disbanding, it should finish
with ccw_device_disband_done() (which leaves the device in offline state)
instead of ccw_device_verify_done() (which leaves the device in online state).
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add support for multiple subchannel sets.  Works with arbitrary devices in
subchannel set 1 and is transparent to device drivers.  Although currently
only two subchannel sets are available, this will work with the architectured
maximum number of subchannel sets as well.
Signed-off-by: NCornelia Huck <cohuck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

struct channel_subsystem encapsulates several per channel subsystem
properties, like status of chpids or the global path group id.
Signed-off-by: NCornelia Huck <cohuck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch introduces a struct subchannel_id containing the subchannel number
(formerly referred to as "irq") and switches code formerly relying on the
subchannel number over to it.

While we're touching inline assemblies anyway, make sure they have correct
memory constraints.
Signed-off-by: NCornelia Huck <cohuck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If we receive path not operational indications (pnom in pmcw nonzero), we
switch off those paths.  To catch them becoming available again, we have to
recalculate the lpm from the pmcw each time we start path verification.
Signed-off-by: NCornelia Huck <cohuck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!