Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch hopefully contains all necessary changes to support
firmwares for all devices up to atleast 2.13.3.0.
(or: LowerMAC Protocol Rev: 5.5 )

And this is a big win, since:
 * newer firmwares are more stable and reliable than the old ones.
 * no problems anymore with packages > 1399 octets (without lowering the MTU).
 * monitor mode finally works on USB for more than just a few seconds.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

p54_set_filter has a way too many unnecessary "magic" parameters and values.
This patch axes all superfluous parameters and gives most of the magic values appropriate names.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Replace a hardcoded Analog switch (which breaks on N-PHY) by a call to
the switch_analog PHY operation.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This moves the Analog switching code into the PHY files.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds the necessary changes to support LM87 firmwares.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k uses LED classdev functions, so it needs to either select or depend
on them.  This patch uses the same selects that ath5k uses...

drivers/built-in.o: In function `ath_unregister_led':
main.c:(.text+0x138c1d): undefined reference to `led_classdev_unregister'
drivers/built-in.o: In function `ath_register_led':
main.c:(.text+0x139c16): undefined reference to `led_classdev_register'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
cc: Jouni Malinen <jmalinen@atheros.com>
Acked-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This splits the PHY allocation from the PHY init.
This is needed in order to properly support Analog handling.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Both p54pci and p54usb uses a good chunk of device specific code to
get the data from the device's eeprom into the drivers memory.

So, this patch reduces the code size and will it make life easier if
someone wants to implement ethtool eeprom dumping features.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch greatly reduces one of biggest memory waste in the driver.

The firmware headers provides the right values for extra head-/tailroom
and mtu size which are usually much lower than the old hardcoded ones.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I'm afraid, I forgot to add the following lines to
7262d593 ("p54pci: rx tasklet refactoring").

These changes are necessary to ensure loop termination.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds definitions for the LP-PHY radios.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds read/write phyops for the LP-PHY and LP-PHY radios.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds template code for the LP-PHY.
No actual functionality is implemented.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sourcecode files for PHY code are named by phy_XXX.{c,h}
where XXX is the PHY type.
Move the N-PHY code to match the other files.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This moves the remaining code from phy.c to phy_a.c
phy.c is removed.
No functional change. Just moving code and removing dead code.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is obviously good for userspace to know up front which
interface modes a given piece of hardware might support (even
if adding such an interface might fail later because of
concurrency issues), so let's make cfg80211 aware of that.
For good measure, disallow adding interfaces in all other
modes so drivers don't forget to announce support for one mode
when they add it.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NStephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * No code changes...

 * Split hw.c to multiple files for better maintenance and add some documentation on each file
   code is going to grow soon (eeprom.c for example is going to get much stuff currently developed
   on ath_info) so it's better this way.

 * Rename following functions to maintain naming scheme:

     ah_setup_xtx_desc -> ah_setup_mrr_tx_desc
     (Because xtx doesn't say much, it's actually
     a multi-rate-retry tx descriptor)

     ath5k_hw_put_tx/rx_buf - > ath5k_hw_set_tx/rxdp
     ath5k_hw_get_tx/rx_buf -> ath5k_hw_get_tx/rxdp
     (We don't put any "buf" we set descriptor pointers on hw)

     ath5k_hw_tx_start -> ath5k_hw_start_tx_dma
     ath5k_hw_start_rx -> ath5k_hw_start_rx_dma
     ath5k_hw_stop_pcu_recv -> ath5k_hw_stop_rx_pcu
     (It's easier this way to identify them, we also
     have ath5k_hw_start_rx_pcu which completes the
     set)

     ath5k_hw_set_intr -> ath5k_hw_set_imr
     (As in get_isr we set imr here, not "intr")

  * Move ath5k_hw_setup_rx_desc on ah->ah_setup_rx_desc so we can
    include support for different rx descriptors in the future

  * Further cleanups so that checkpatch doesn't complain
    (only some > 80 col warnings for eeprom.h and reg.h as usual
    due to comments)

  Tested on 5211 and 5213 cards and works ok.

Changes-licensed-under: ISC
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Acked-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is valid to pass &gphy->rfatt and &gphy->bbatt as rfatt and bbatt
pointer arguments to the function. So we have to use memmove for the
possibly overlapping memory areas.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch rewrites the TX power recalculation algorithms to scale better
with changed enviromnent. If there's low
TX traffic, the power will be checked against the desired values
every 60 seconds.
If there is high TX traffic, the check is redone every 2 seconds. This improves
the reaction times a lot and confuses the rate control less.
It will also reduce the time it initially takes to tune to a new TX power
value. With the old algorithm it could take about 30 to 45 seconds to settle to
a new power value. This will happen in about two to four seconds now.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch implements a dynamic "ops" based PHY API.
This is needed in order to conveniently support future PHY types
to avoid the "switch"-hell.

This patch does not change any functionality. It just moves lots
of code from one place to another and adjusts it for the changed
data structures.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make sure the skb->data pointer points to the frame data, not the TX
descriptor. The frame dumping code relies on that.
Signed-off-by: NMattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of using the PLCP flag to indicate if the
signal value is plcp or the bitrate we should add
a new flag to mark the bitrate type explicitely.
This is usefull when new types are added later for
rt2800.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The txop parameter is supported by rt61pci and rt73usb,
and thus should be written to the register instead
of using the fixed value set during initialization.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some hardware configuration registers such as antenna and channel configuration
can only be written when the radio is enabled. Previously, we didn't consider
this, so some configuration items could be set inconsistently after reenabling
the radio. This patch changes the config() handler to only reprogram the
hardware when the radio is enabled. Configuration changes that are made while
the radio is off are postponed until the radio is switched back on. We also
leave the radio turned off during initialization and only enable it when
requested by mac80211. This allows us to get rid of the DIRTY_CONFIG flag,
because the device is now guaranteed to be completely initialized when brought
up by mac80211.
Signed-off-by: NMattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If a driver requests additional headroom it should
be mapped to DMA as well because it will be send to
the hardware as well (as form of extra descriptor).
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some of the flags should be accessed atomically to
prevent race conditions. The flags that are most important
are those that can change often and indicate the actual
state of the device, queue or queue entry.

The big flag rename was done to move all state flags to
the same naming type as the other rt2x00dev flags and
made sure all places where the flags were used were changed. ;)

Thanks to Stephen for most of the queue flags updates,
which fixes some of the most obvious consequences of the
race conditions. Among those the notorious:

rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
Signed-off-by: NStephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use kernel doc syntax for comments and remove a few unused macros.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When AR_DurUpdateEna is set, the frame's duration field
is updated by the MAC based on the current rate.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch moves the all of p54pci's receiver code out of the
bloated interrupt handler routine and into a less critical tasklet.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The firmware supports 8 different queues and not only 4.
So, let's make some room for further tasks (ap/adhoc support)
in this area.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

p54_rx_frame_sent will alter the tx_queue. Therefore we should hold
the lock to protect against concurrent p54_assign_address calls.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Ever wondered why the signal was so bad with p54 compared to madwifi, or intel?

Well, if you have revision 1 rssi calibration curve points in your EEPROM, then wonder no more.
The firmware wants a extra 1 byte padding for every curve point. But someone forgot to put
them into the EEPROM's data structure...

So now, big question: what happens when we blindly "memcpy" these data points?
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver(s) below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
  drivers/net/wireless/b43legacy/main.c
  drivers/net/wireless/iwlwifi/iwl-3945-led.c
  drivers/net/wireless/iwlwifi/iwl-led.c
  drivers/net/wireless/iwlwifi/iwl-rfkill.c

This patch removes the said #include <version.h>.
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Replace the internal ath9k implementation of multicast/broadcast frame
power save buffering (AP mode) in ath9k with use of mac80211
ieee80211_get_buffered_bc() mechanism. This removes quite a bit of
duplicated functionality and simplifies the driver part.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>