When removing an IGTK, iwl_mvm_send_sta_igtk() was
called before station ID was retrieved, so the function
was invoked with an invalid station ID. Fix this by first
getting the station ID.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=192411Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The race happens when we send ADD_STA(auth->assoc) -> LQ_CMD
between the commands the FW sometimes loses the medium for AUX, and
sends a ndp to the AP and the flow becomes, ADD_STA -> send ndp -> LQ_CMD
the problem is that there's no rates yet defined for sending the ndp and
FW generates an assert.

The fix: change the order of the commands to LQ_CMD -> ADD_STA
Signed-off-by: NMordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The session protection set for association is only removed when
BSS_CHANGED_BEACON_INFO is set and BSS_CHANGED_ASSOC is not set.

However, mac80211 may set both on association (in case a beacon was
already received). In this case, mac80211 will not set
BSS_CHANGED_BEACON_INFO on the next beacons because it has already
notified the beacon change, so the session protection is never removed
(until the session protection ends).

When a CSA is received within this time, the station will fail to
folllow the channel switch because it cannot schedule the time event.

Fix this by removing the session protection when
BSS_CHANGED_BEACON_INFO and BSS_CHANGED_ASSOC are both set.
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Currently, when getting a RFKILL interrupt, the transport enters a flow
in which it stops the device, disables other interrupts, etc. After
stopping the device, the transport resets the hw, and sleeps. During
the sleep, a context switch occurs and host commands are sent by upper
layers (e.g. mvm) to the fw. This is possible since the op_mode layer
and the transport layer hold different mutexes.

Since the STATUS_RFKILL bit isn't set, the transport layer doesn't
recognize that RFKILL was toggled on, and no commands can actually be
sent, so it enqueues the command to the tx queue and sets a timer on
the queue.

After switching context back to stopping the device, STATUS_RFKILL is
set, and then the transport can't send the command to the fw.
This eventually results in a queue hang.

Fix this by setting STATUS_RFKILL immediately when
the interrupt is fired.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In https://bugzilla.kernel.org/show_bug.cgi?id=177341 Bob
reported a UBSAN WARNING on rs.c in iwldvm.
Fix the same bug in iwlmvm.

This because
	i = index - 1;
	for (mask = (1 << i); i >= 0; i--, mask >>= 1)

is unsafe: i could be negative and hence we can call <<
on a negative value.
This bug doesn't have any real impact since the condition
of the for loop will prevent any usage of mask.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=177341Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In https://bugzilla.kernel.org/show_bug.cgi?id=177341 Bob
reported a UBSAN WARNING on rs.c.

Undefined behaviour in drivers/net/wireless/intel/iwlwifi/dvm/rs.c:746:18

This because
	i = index - 1;
	for (mask = (1 << i); i >= 0; i--, mask >>= 1)

is unsafe: i could be negative and hence we can call <<
on a negative value.
This bug doesn't have any real impact since the condition
of the for loop will prevent any usage of mask.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=177341Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Enabling the RTPM Kconfig option can be fairly risky.
Runtime PM must be validated against a specific platform
before it can be safely enabled. Hence, it makes no sense
for distros and other big OS vendors to enable it since
they ship code to various systems and unknown platform.

Make sure that this is hinted properly by making the
IWLWIFI_PCIE_RTPM Kconfig option depend on EXPERT.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=172411Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

David reported that the code I added uses the decrement
and increment operator on a boolean variable.

Fix that.

Fixes: 0cd58eaa ("iwlwifi: pcie: allow the op_mode to block the tx queues")
Reported-by: NDavid Binderman <dcb314@hotmail.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we send a deauth to a station we don't know about, we
need to use the PROBE_RESP queue. This can happen when we
send a deauth to a station that is not associated to us.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When NSSN is behind the reorder buffer due to timeout
the reorder timer isn't getting re-armed until NSSN
catches up. Fix it.

Fixes: 0690405f ("iwlwifi: mvm: add reorder timeout per frame")
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In DQA mode, first_agg_queue is initialized to
IWL_MVM_DQA_MIN_DATA_QUEUE. This causes two bugs in the tx response
flow:

1. When TX fails, we set IEEE80211_TX_STAT_AMPDU_NO_BACK regardless
   if we actually have aggregation open on the queue. This causes
   mac80211 to send a BAR frame even though there is no aggregation
   open.
   Fix that by simply checking the AMPDU flag that is set on by
   mac80211 for AMPDU packets.

2. When reclaiming frames in aggregation mode, we reclaim based on
   scheduler ssn and not the SN.
   The reason is that scheduler ssn may be ahead of SN due to a hole
   in the BA window that was filled.
   However, if we have aggregations open on IWL_MVM_DQA_BSS_CLIENT_QUEUE
   the reclaim flow will still go to the code of non-aggregation
   instead of the aggregation code since IWL_MVM_DQA_BSS_CLIENT_QUEUE
   is smaller than IWL_MVM_DQA_MIN_DATA_QUEUE, although it is a valid
   aggregation queue.
   Fix that by always using the aggregation reclaim code by default in
   DQA mode (currently it is implicitly used by default for all queues
   except the reserved BSS queue).

Fixes: cf961e16 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Handling of the number of space time streams was missing for HT rate in
rate printing function. Fix it.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When getting RF_KILL and disabling radio, the device gets stopped
and reset. This erases the IVAR table that matches the interrupt
to its cause, and is essential for MSIX proper functionality.
Till now, the table wasn't re-configured after the reset, and
therefore the interrupt that enabled radio didn't fire on the
right irq, and the driver didn't handle it correctly.

To fix this, configure the IVAR table again after resetting the
device.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

During the suspend/resume flow some HW blocks are reset.  This causes
the IVAR table to be completely erased.  This table is where interrupt
causes are bound to specific IRQs.  When the table is empty the
interrupt handlers are not called correctly.  Fix this by reconfiguring
the IVAR table after resume.

Fixes: 2e5d4a8f ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The MSIX configuration flow includes two different stages:
configuring the HW by writing to the IVAR table and configuring the SW
to reflect the HW configuration.
The HW configuration is needed on each HW reset,
whereas the SW configuration is only needed during the init flow.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

msix configuration functions should be called by other functions.
For example by pcie_d3_resume, move it above to enable it.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Support new version of beacon template command which deprecates
the use of the tx command inside.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When resuming, it's possible for the following scenario to occur:

 * iwl_pci_resume() enables the RF-kill interrupt
 * iwl_pci_resume() reads the RF-kill state (e.g. to 'radio enabled')
 * RF_KILL interrupt triggers, and iwl_pcie_irq_handler() reads the
   state, now 'radio disabled', and acquires the &trans_pcie->mutex.
 * iwl_pcie_irq_handler() further calls iwl_trans_pcie_rf_kill() to
   indicate to the higher layers that the radio is now disabled (and
   stops the device while at it)
 * iwl_pcie_irq_handler() drops the mutex
 * iwl_pci_resume() continues, acquires the mutex and calls the higher
   layers to indicate that the radio is enabled.

At this point, the device is stopped but the higher layers think it's
available, and can call deeply into the driver to try to enable it.
However, this will fail since the device is actually disabled.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Support differentiating between two phys for a000 devices
in order to load the correct firmware.
Eventually when moving completely to the new phy we will be
able to remove this.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The iwl_drv structure contains trans which already contains cfg, so
storing cfg separately in iwl_drv is redundant.  Remove it and access
trans->cfg instead.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When iwl_drv_start() is called, trans->cfg must already be set, so
there's no need to pass cfg separately, since it can be accessed
directly from trans->cfg.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Unify code, remove redundant assignments.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When a small frame is copied completely into the skb->head, the code
doesn't take alignment into account, making mac80211 copy it again
later on architectures that need the alignment. Avoid this by taking
the PAD flag from the device into account when copying.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In DQA mode the check whether to decrement the pending frames
counter relies on the tid status and not on the txq id.
This may result in an inconsistent state of the pending frames
counter in case frame is queued on a non aggregation queue but
with this TID, and will be followed by a failure to remove the
station and later on SYSASSERT 0x3421 when trying to remove the
MAC.
Such frames are for example bar and qos NDPs.
Fix it by aligning the condition of incrementing the counter
with the condition of decrementing it - rely on TID state for
DQA mode.
Also, avoid internal error like this affecting station removal
for DQA mode - since we can know for sure it is an internal
error.

Fixes: cf961e16 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Our 9000 device supports 64 bit DMA address for RX only, and
not for TX.
Setting DMA mask to 64 for the whole device is erroneous - we
can do it only for a000 devices where device is capable of
both RX & TX DMA with 64 bit address space.

Fixes: 96a6497b ("iwlwifi: pcie: add 9000 series multi queue rx DMA support")
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

A few of the static queues are enabled along with the bcast
STA. Make sure they are removed along with it, rather than
waiting for the mac ctxt release.

This is needed because we sometimes have a STA being removed
and then added again (either with the same sta_id or a
different one). If we wait for the mac ctxt release we will
try to allocate the queues again (as this is currently done
in the STA allocation and not in the MAC init) although
they weren't freed, and even if the sta_id of the STA has
changed.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Instead of setting the tx_cmd length in the mvm code, which is
complicated by the fact that DQA may want to temporarily store
the SKB on the side, adjust the length in the PCIe code which
also knows about this since it's responsible for duplicating
all those headers that are account for in this code.

As the PCIe code already relies on the tx_cmd->len field, this
doesn't really introduce any new dependencies.

To make this possible we need to move the memcpy() of the TX
command until after it was updated.

This does even simplify the code though, since the PCIe code
already does a lot of manipulations to build A-MSDUs correctly
and changing the length becomes a simple operation to see how
much was added/removed, rather than predicting it.

Fixes: 24afba76 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We don't really need clear the skb's status area nor store the
dev_cmd into it until we really commit to the frame by handing
it to the transport - defer those operations until just before
we do that.

This doesn't entirely fix the bug with frames not getting sent
out after having been deferred due to DQA, because it doesn't
restore the info->driver_data[0] place that was already set to
zero (or another value) by the A-MSDU logic.

Fixes: 24afba76 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The firmware will soon actually look at the AID field, and
when it does that it'll try to ensure that the AID is never
changing. Due to the way the station is added, it may start
with an invalid AID before it's associated, so to ensure a
constant AID (once it becomes non-zero), track the station
state and set the AID only when the station is associated
and when it disassociates.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This fixes a long-standing bug that was introduced when this code
was introduced: cfg80211 passes a pointer, but we treat it as if
it was passing a value. The result is that we pass the pointer to
the firmware, instead of the value. It's not clear how this could
ever have worked, unless the firmware is ignoring this value.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When driver needs to access the contents of a streaming DMA buffer
without unmapping it it should call dma_sync_single_for_cpu().
Once the call has been made, the CPU "owns" the DMA buffer and can
work with it as needed.
Before the device accesses the buffer, however, ownership should be
transferred back to it with dma_sync_single_for_device().
Both calls weren't performed by the driver, resulting with odd paging
errors on some platforms. Fix it.

Fixes: a6c4fb44 ("iwlwifi: mvm: Add FW paging mechanism for the UMAC on PCI")
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Support getting alive from two LMACs and dumping debug
data from both.
Deprecate older alive notifications no one is using.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There's already a variable with the result in scope, use that.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

If iwl_mvm_find_free_queue() doesn't find a free queue, it will
return an inactive one.
However, not all the call paths free this queue before reassigning
it, which is a bug.
Check it in other paths and act accordingly.

Fixes: 9794c64f ("iwlwifi: mvm: support dqa queue inactivation upon timeout")
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For CDB devices we will want to configure scan parameters
per band.
Support the new scan API for now. Logic per band will be
added in the future.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For CDB arch there is another auxiliary mac.
Support statistics APIs that were changed to reflect that.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Currently we have up to 3 phy contexts - defined by NUM_PHY_CTX.
However - some code paths validate the ID by using MAX_PHYS define
which is set to 4.
While there is no harm it is incorrect - since the maximum is 3.
Remove the define and use the correct one.
Cleanup the code a bit while at it.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Since offchannel activity doesn't always require a BSS, e.g. ANQP
sessions, offchannel frames should not use the BSS queue, because it
might not be initialized.
Use the auxilary queue instead

Fixes: e3118ad7 ("iwlwifi: mvm: support tdls in dqa mode")
Signed-off-by: NBeni Lev <beni.lev@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add to the v1 of the mfuart loading notification, the size
of the mfuart image, and write it to dmesg once the notification
is received.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For a000 devices the INIT and RT images are unified to one
image.
The changes in the flow are the following:
* Driver load only RT firmware - meaning that the nvm access
  command will be done in the RT image load flow.
* A new command (NVM_ACCESS_COMPLETE) now signals to the FW that
  the driver is done accessing the NVM and FW can proceed with phy
  calibrations.
* Phy DB is no longer sent from INIT FW to be restored by driver
  for the RT FW - all the phy DB is now internal to the FW.
  INIT complete will now follow the NVM access command, without
  phy DB calls before.
* Paging command is sent earlier in the flow before NVM access
  to enable a complete load of FW.
* caution must be care when restart is called since we may have
  not completed init flow even though we are in RT firmware.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>