gianfar: Fix crashes on RX path (Was Re: [Bugme-new] [Bug 19692] New: linux-2.6.36-rc5 crash with gianfar ethernet at full line rate traffic)

The rx_recycle queue is global per device but can be accesed by many
napi handlers at the same time, so it needs full skb_queue primitives
(with locking). Otherwise, various crashes caused by broken skbs are
possible.

This patch resolves, at least partly, bugzilla bug 19692. (Because of
some doubts that there could be still something around which is hard
to reproduce my proposal is to leave this bug opened for a month.)

Fixes commit: 0fd56bb5 ("gianfar: Add
support for skb recycling")
Reported-by: Nemin ak <eminak71@gmail.com>
Tested-by: Nemin ak <eminak71@gmail.com>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
CC: Andy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a bug in the interaction between ipv6_create_tempaddr and
addrconf_verify.  Because ipv6_create_tempaddr uses the cstamp and tstamp
from the public address in creating a private address, if we have not
received a router advertisement in a while, tstamp + temp_valid_lft might be
< now.  If this happens, the new address is created inside
ipv6_create_tempaddr, then the loop within addrconf_verify starts again and
the address is immediately deleted.  We are left with no temporary addresses
on the interface, and no more will be created until the public IP address is
updated.  To avoid this, set the expiry time to be the minimum of the time
left on the public address or the config option PLUS the current age of the
public interface.
Signed-off-by: NGlenn Wurster <gwurster@scs.carleton.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If privacy extentions are enabled, but no current temporary address exists,
then create one when we get a router advertisement.
Signed-off-by: NGlenn Wurster <gwurster@scs.carleton.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While fixing CONFIG_SPARSE_RCU_POINTER errors, I had to fix accesses to
fz->fz_hash for real.

-	&fz->fz_hash[fn_hash(f->fn_key, fz)]
+	rcu_dereference(fz->fz_hash) + fn_hash(f->fn_key, fz)
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some panic reports in fib_rules_lookup() show a rule could have a NULL
pointer as a next pointer in the rules_list.

This can actually happen because of a bug in fib_nl_newrule() : It
checks if current rule is the destination of unresolved gotos. (Other
rules have gotos to this about to be inserted rule)

Problem is it does the resolution of the gotos before the rule is
inserted in the rules_list (and has a valid next pointer)

Fix this by moving the rules_list insertion before the changes on gotos.

A lockless reader can not any more follow a ctarget pointer, unless
destination is ready (has a valid next pointer)
Reported-by: NOleg A. Arkhangelsky <sysoleg@yandex.ru>
Reported-by: NJoe Buehler <aspam@cox.net>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tg3 driver calls device_set_wakeup_enable() under spin_lock_bh,
which causes a problem to happen after the recent core power
management changes, because this function can sleep now.  Fix this
by moving the device_set_wakeup_enable() call out of the
spin_lock_bh-protected area.
Reported-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch sets the missing CAN_RTR_FLAG if a standard RTR frame is
received.
(For extended frames the CAN_RTR_FLAG was already set correctly.)
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The priv is part of the memory allocated by alloc_candev().
This patch moved the free it after last usage of priv.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we continue on error, we'd likely free the IRQ that we
didn't get, right?
Signed-off-by: NNicolas Kaiser <nikai@nikai.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix pch_can build when CONFIG_PCI is not enabled.  It uses pci interfaces
and data structures, so it should depend on PCI.

drivers/net/can/pch_can.c:1044: error: implicit declaration of function 'pci_enable_msi'
drivers/net/can/pch_can.c:1079: error: implicit declaration of function 'pci_disable_msi'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add __rcu annotations to :
        (struct ip_ra_chain)->next
	struct ip_ra_chain *ip_ra_chain;

And use appropriate rcu primitives.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add __rcu annotation to :
        (struct sock)->sk_filter

And use appropriate rcu primitives to reduce sparse warnings if
CONFIG_SPARSE_RCU_POINTER=y
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

add __rcu annotation to (struct net)->gen, and use
rcu_dereference_protected() in net_assign_generic()
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add __rcu annotations to :
	(struct netdev_rx_queue)->rps_map
	(struct netdev_rx_queue)->rps_flow_table
	struct rps_sock_flow_table *rps_sock_flow_table;

And use appropriate rcu primitives.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One of the previous tproxy related patches split IPv6 defragmentation and
connection tracking, but did not correctly add Kconfig stanzas to handle the
new dependencies correctly. This patch fixes that by making the config options
mirror the setup we have for IPv4: a distinct config option for defragmentation
that is automatically selected by both connection tracking and
xt_TPROXY/xt_socket.

The patch also changes the #ifdefs enclosing IPv6 specific code in xt_socket
and xt_TPROXY: we only compile these in case we have ip6tables support enabled.
Signed-off-by: NKOVACS Krisztian <hidden@balabit.hu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

(struct ip6_tnl)->next is rcu protected :
(struct ip_tunnel)->next is rcu protected :
(struct xfrm6_tunnel)->next is rcu protected :

add __rcu annotation and proper rcu primitives.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

(struct net_device)->garp_port is rcu protected :
(struct garp_port)->applicants is rcu protected :

add __rcu annotation and proper rcu primitives.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

(struct net_device)->ip6_ptr is rcu protected :

add __rcu annotation and proper rcu primitives.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

(struct net_device)->vlgrp is rcu protected :

add __rcu annotation and proper rcu primitives.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver tries to do up to half-second udelay()
calls, which overflows on x86-64.
Reported-by: NAndi Kleen <andi@firstfloor.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Three is definitely too low, and we know from reports that GRE tunnels
stacked as deeply as 37 levels cause stack overflows, so pick some
reasonable value between those two.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When searching for a free entry in either mlx4_register_vlan() or
mlx4_register_mac(), and there is no free entry, the loop terminates without
updating the local variable free thus causing out of array bounds access. Fix
this by adding a proper check outside the loop.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On a busy network, the macb driver could get stuck in the interrupt
handler, quickly triggering the watchdog, due to a confluence of
factors:

 1. macb_poll re-enables interrupts unconditionally, even when it will
    be called again because it exhausted its rx budget

 2. macb_interrupt only disables interrupts after scheduling
    macb_poll, but scheduling fails when macb_poll is already scheduled
    because it didn't call napi_complete

 3. macb_interrupt loops until the interrupt status register is clear,
    which will never happen in this case if the driver doesn't disable
    the RX interrupt

Since macb_interrupt runs in interrupt context, this effectively locks
up the machine, triggering the hardware watchdog.

This issue was readily reproducible on a flooded network with a
modified 2.6.27.48 kernel. The same problem appears to still be in the
2.6.36-rc8 driver code, so I am submitting this patch against that
version. I have not tested this version of the patch except to make
sure the kernel compiles.
Signed-off-by: NJoshua Hoke <joshua.hoke@sixnet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We're setting skb->ip_summed to CHECKSUM_NONE for all non-TCP pkts, making the stack
recompute checksum.This is a bug for UDP pkts for which cso must be used.
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calling netif_carrier_off before register_netdev was causing the network interface
to miss a linkwatch pending event leading to  an inconsistent state if the link
is not up when interface is initialized.This is now invoked after register_netdev.
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only negative return from bind_qsets() should be considered an error and
propagated.
It fixes an issue reported by IBM on P Series platform.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Tested-by: NNishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Timing issues in microcode for some devices can cause a compressed BA to
be sent to the driver prior to returning any a-MPDU notification.
Traces show RTS-CTS is exchanged and then the timer fires which causes an
empty BA to be sent which acknowledges nothing.  This results in a noisy
printk. Only print the message if the bitmap is non-zero.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since aggregation is usually triggered by tx completion, a hardware
reset (because of beacon stuck, tx hang or baseband hang) can
significantly delay the transmission of the next AMPDU (until the next
tx completion event).
Fix this by rescheduling aggregation after such a reset.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes the following mishap:

BUG: scheduling while atomic: wpa_supplicant/4164/0x00000002
Modules linked in: carl9170 mac80211 [...]
Pid: 4164, comm: wpa_supplicant Not tainted 2.6.36-wl+ #119
Call Trace:
 [<c13779a9>] ? schedule+0x349/0x4c0
 [<c13780d6>] ? schedule_timeout+0x106/0x1e0
 [<c1037f50>] ? process_timeout+0x0/0x10
 [<c1377e8d>] ? wait_for_common+0x9d/0x140
 [<c1029110>] ? default_wake_function+0x0/0x10
 [<f80c6080>] ? carl9170_exec_cmd+0xf0/0x250 [carl9170]
 [<f80c695e>] ? carl9170_set_mac_reg+0x5e/0x70 [carl9170]
 [<f80c3f76>] ? carl9170_op_add_interface+0x176/0x310 [carl9170]
 [...]

rcu_read_unlock() call was erroneously placed after the
sync. function carl9170_mod_virtual_mac.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Station addition in ieee80211_ibss_rx_queued_mgmt is not updating
sta->last_rx which is causing station expiry in ieee80211_ibss_work
path. So sta addition and deletion happens repeatedly.

CC: stable@kernel.org
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The wl1251 move accidently renamed wl1251_sdio and wl1251_spi
modules to just sdio and spi. Restore proper module names.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Acked-by: NKalle Valo <kvalo@adurom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ath9k aggregation code was already checking the rate control probe flag
to prevent starting an aggregate frame with a sampling rate. What was missing
was closing an aggregate before adding a probing frame to it.
Without that, rate control cannot have precise control over probing, which
delays using faster rates when the channel conditions improve.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If ah->curchan is uninitialized, the channel index is bogus, which leads
to invalid memory access when the cycle counters are updated.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We are not handling all divide by zero cases in paprd.
Add additional checks for divide by zero cases in papard.

This patch has fixes intended for kernel 2.6.36.

Cc: stable@kernel.org
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This updates the initvals for the AR9003 2.2 chipsets. The initvals
are the initial register values we use for our registers upon hardware
reset. This synchs up the initvals to match what our latest recommendation
from our systems engineering team.

The description of changes in this update:

        Improves ability to support very strong Rx conditions.
        Enhances DFS support for AP-mode.
        Improves performance of Tx carrier leak calibration.
        Adds support for Japan channel 14 Tx filtering requirements.
        Improves Tx power accuracy.

Impact:

        Update required to address degraded throughput at very short range.
        Update required for AP-mode DFS certification.
        Update required to comply to IEEE Tx carrier leak specification.
        May not meet expected +/- 2 dB Tx power accuracy without update.

The most important fix here would be the TX carrier leakage required
to comply with IEEE 802.11 specifications. The group of changes have
been tested all together in one release.

References:

	Osprey 2.2 header file ver #33

Checksums:

$ ./initvals -f ar9003-2p2
0x000000004a488fc7        ar9300_2p2_radio_postamble
0x0000000046cb1300        ar9300Modes_lowest_ob_db_tx_gain_table_2p2
0x00000000e912711f        ar9300Modes_fast_clock_2p2
0x0000000037ac0ee8        ar9300_2p2_radio_core
0x00000000047a7700        ar9300Common_rx_gain_table_merlin_2p2
0x0000000003f783bb        ar9300_2p2_mac_postamble
0x00000000301fc841        ar9300_2p2_soc_postamble
0x000000005ec8075f        ar9200_merlin_2p2_radio_core
0x0000000083372ffa        ar9300_2p2_baseband_postamble
0x00000000c4f59974        ar9300_2p2_baseband_core
0x00000000e20d2e72        ar9300Modes_high_power_tx_gain_table_2p2
0x000000007fd55c70        ar9300Modes_high_ob_db_tx_gain_table_2p2
0x0000000029495000        ar9300Common_rx_gain_table_2p2
0x0000000042cb1300        ar9300Modes_low_ob_db_tx_gain_table_2p2
0x00000000c4739cd6        ar9300_2p2_mac_core
0x000000003521a300        ar9300Common_wo_xlna_rx_gain_table_2p2
0x00000000a15ccf1b        ar9300_2p2_soc_preamble
0x0000000029734396        ar9300PciePhy_pll_on_clkreq_disable_L1_2p2
0x000000002d834396        ar9300PciePhy_clkreq_enable_L1_2p2
0x0000000029834396        ar9300PciePhy_clkreq_disable_L1_2p2

$ ./initvals -f ar9003-2p2 | sha1sum
0ceddb5cf66737610fb51f04cf3e9ff71870c7b4  -

Cc: stable@kernel.org
Cc: Yixiang Li <yixiang.li@atheros.com>
Cc: Don Breslin <don.breslin@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch 4f366c5d:

	wireless: only use alpha2 regulatory information from country IE

removed some complex intersection we were always doing between the AP's
country IE info and what we got from CRDA. When CRDA sent us back a
regulatory domain we would do some sanity checks on that regulatory
domain response we just got. Part of these sanity checks included
checking that we already had performed an intersection for the
request of NL80211_REGDOM_SET_BY_COUNTRY_IE type.

This mean that cfg80211 was only processing country IEs for cases
where we already had an intersection, but since we removed enforcing
this this is no longer required, we should just apply the country
IE country hint with the data received from CRDA.

This patch has fixes intended for kernels >= 2.6.36.

Cc: stable@kernel.org
Reported-by: NEaswar Krishnan <easwar.krishnan@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>