Current R-Car sound driver is using DMAEngine directly,
but, ASoC is requesting to use common DMA transfer method,
like snd_dmaengine_pcm_trigger() or dmaengine_pcm_ops.
It is difficult to switch at this point, since Renesas
driver is also supporting PIO transfer.
This patch uses dmaengine_prep_dma_cyclic() instead
of dmaengine_prep_slave_single().
It is used in requested method,
and is good first step to switch over.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Sound data needs to be sent to R-Car sound SSI when playback.
But, there are 2 interfaces for it.
1st is SSITDR/SSIRDR which are mapped on SSI.
2nd is SSIn_BUSIF which are mapped on SSIU.

2nd SSIn_BUSIF is used when DMA transfer,
and it is always used if sound data came from via SRC.
But, we can use it when SSI+DMA case too.
(Current driver is assuming 1st SSITDR/SSIRDR for it)

2nd SSIn_BUSIF can be used as FIFO.
This is very helpful/useful for SSI+DMA.

But DMA address / DMA ID are not same between 1st/2nd cases.
This patch care about these settings.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

dmaengine_prep_slave_single() expects a enum dma_transfer_direction and not a
enum dma_data_direction. Since the integer representations of both DMA_TO_DEVICE
and DMA_MEM_TO_DEV aswell as DMA_FROM_DEVICE and DMA_DEV_TO_MEM have the same
value the code worked fine even though it was using the wrong type.

Fixes the following warning from sparse:
	sound/soc/sh/rcar/core.c:227:49: warning: mixing different enum types
	sound/soc/sh/rcar/core.c:227:49:     int enum dma_data_direction  versus
	sound/soc/sh/rcar/core.c:227:49:     int enum dma_transfer_direction
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Current dma name search loop didn't care about SSI index
This patch fixes it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

ad32d0c7
(ASoC: rsnd: add rsnd_gen_dma_addr() for DMAC addr)
added rsnd_gen_dma_addr() to calculate DMA addr,
but, it is necessary only for Gen2.
This patch ignores Gen1 case.
Kernel will be panic without this patch.
Special thanks to Simon
Reported-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NMark Brown <broonie@linaro.org>

Index of dma name should use -1, not +1 when capture case.
Thank you Dan.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

The DMAC src/dst addr needs to be set from driver when DT case.
(It was set from SoC/DMAEngine code when non-DT case)
This patch adds rsnd_gen_dma_addr() to set DMAC src/dst addr.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Renesas sound driver is supporting to use DMAEngine.
But, DMA slave channel name "tx", "rx" is not enough
in DT case.
Becuase, it has many ports and path combination.

This patch adds rsnd_dma_of_name() to find
DMA channel name, for example
memory to SSI0 is "mem_ssi0",
SSI0 to memory is "ssi0_mem",
SSI0 to SRC0   is "ssi0_src0",
SRC0 to SSI0   is "src0_ssi0",
SRC0 to DVC0   is "src0_dvc0"...

Renesas sound want to use PIO transfer mode for some reasons.
It will be PIO tranfer mode if device node doesn't have
DMA settings.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Renesas sound driver uses many modules (= SSI/SRC/DVC),
and each module had own name.
But, each module name can be used as several purpose,
like clock name, DMA name etc...
This patch uses common name for each module.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Renesas sound driver is supporting Gen1/Gen2.
SRC probe can return error if it was unknown
generation.
Now, rsnd_src_non_ops is not needed.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

DT DMA support needs struct platform_device pointer,
and it can get struct device pointer from platform_device.
Save platform_device instead of device.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Driver needs to call of_node_put() after of_get_chile_by_name()
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Use the %pap printk specifier to print resource_size_t variables. This
fixes warnings on platforms where resource_size_t has a different size
than int.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch adds DVC (Digital Volume Controller)
support which is member of CMD unit.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

rsnd_mod_ops would like to come to use multi parameter.
modify macro to enable it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Now, it can get rsnd_dai_stream pointer from rsnd_mod.
Remove duplicate parameter from rsnd_mod_ops
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

SRC module needs ADINR register settings,
but, it has many similar xxx_ADINR register,
and needs same settings.
This patch adds rsnd_get_adinr() to sharing code.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Current R-Car sound supports only SRC/SSI,
but, other module will be supported.
This patch adds rsnd_path_parse() macro to share code
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Now, all platform is using new style rsnd_dai_platform_info.
Keeping compatibility is no longer needed.
We can cleanup code.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

All platform which used old style was
switched to new style.
R-Car sound can remove old style clock support,
use device dependent clock now.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

rsnd_soc_dai_trigger() will be called
after rsnd_dai_pointer_update() function
which is using rsnd_lock().
Thus, it should be called from outside of rsnd_lock().
Kernel will be hangup without this patch.
Special thanks to Kataoka-san
Reported-by: NRyo Kataoka <ryo.kataoka.wt@renesas.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

As with the previous commit, before a clock can be used it must be prepared
for use. Change from clk_enable() and clk_disable() to the versions of the
calls which also prepare and un-prepare the clocks.

Will fix warnings from the clock code when this is used.
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

src might not exist.
kernel will be hung-up without this patch in such case.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Support for loading the Renesas R-Car sound driver via DeviceTree.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

SND_SOC_DAIFMT_CBx_CFx means "codec" side master/slave mode.
Then, rcar will be master mode if it was SND_SOC_DAIFMT_CBS_CFS.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

R-Car sound has SCU unit which has SRC/CTU/MIX/DVC,
and current rsnd driver has scu.c and scu module.
Current scu.c has SRC support only.
My first concept was control these feature on scu.c
but, it become difficult and un-understandable now.
This patch rename scu to src
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Now, rsnd_xxx_remove() do nothing.
remove these
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

rsnd_dai_remove() called rsnd_path_exit(),
but these memory will be cleaned automatically.
Because it is created by devm_kzalloc().
nothing to do on rsnd_dai_remove()
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Now, it can use .probe
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Now, it can use .probe
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Each rsnd mod needs specific probe method,
and its best timing is DAI probe timing.
But current code runs it mod probe timing.
This patch adds new probe/remove callback to solve it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Current R-Car sound driver is assuming that
SCU mod is used even though it is not needed.
Because scu.c is controlling SSIU too.
(it is Gen1 compatibility)
But, SCU mod will be really not used if new platform dai
feature was added.
Thus, rsnd_scu_ssi_mode_init() is called from SSI
directory by this patch.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Current R-Car sound driver is assuming that
SCU mod is used even though it is not needed.
Because scu.c is controlling SSIU too.
(it is Gen1 compatibility)
But, SCU mod will be really not used if new platform dai
feature was used.
Thus, SSIU irq setting is called from SSI
directory by this patch.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Current rsnd driver is assuming that SCU/SRU ID is
same as SSIU/SSI ID, because Gen1 can't select it.
But, Gen2 can select it.
The SCU/SRU/SSIU/SSI pair depends on the platform.
This patch get correct SCU ID from platform info.
To keep compatible, it still assuming SCU ID = SSI ID
if platform doesn't have info
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

R-Car sound DAI consists from SSI/SCU/SSIU/SRU...
Current R-Car sound DAI is decided from these settings,
but it is intuitively unclear, and is not good design for DT support.
This patch adds new rsnd_dai_platform_info to solve this issue.

But now, many platform is using this driver without
rsnd_dai_platform_info.
So, this patch still supports DAI settings via SSI to keep compatible.
It will be removed in next Linux version.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Gen1/Gen2 code never be used in same time.
Thus, driver can share Gen1 only register and Gen2 only register.
It can reduce memory too.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

rsnd_adg_ssi_ws_timing_gen2() returns SSI WS timing,
and it used "mod" as parameter.
but, this "mod" is sometimes not ssi mod.
Get SSI mod from rsnd_dai_stream
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

R-Car sound consists of many devices.
It will have more device support in the future.
Thus, for each probe become now function pointer array.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>