Optimized MFI adapters' OCR path, particularly
megasas_wait_for_outstanding() function.
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Make instance->adprecovery variable atomic and removes hba_lock spinlock
while accessing instance->adprecovery.
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch will add capability in driver to tell firmware that it can
throttle IOs in case controller's queue depth is downgraded post OFU
(online firmware upgrade). This feature will ensure firmware can be
downgraded from higher queue depth to lower queue depth without needing
system reboot. Added throttling code in IO path of driver, in case OS
tries to send more IOs than post OFU firmware's queue depth.
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

1. For iMR controllers, firmware will report two queue depths:

   - Controller-wide queue depth
   - LDIO queue depth (240)

Controller-wide queue depth will be greater among the two. Using this
new feature, iMR can provide larger Queue depth(QD) for JBOD and limited
QD for Virtual Disk(VD).

2. megaraid_sas driver will throttle read/write LDIOs based on "LDIO
Queue Depth".

3. Dual queue depth can be enabled/disabled via module parameter. It is
enabled by default if the firmware supports it. Only specific firmware
builds will enable the feature.

4. Added sysfs parameter "ldio_outstanding" which permits querying the
number of outstanding LDIO requests at runtime.
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

build_and_issue_cmd should return SCSI_MLQUEUE_HOST_BUSY for a few error
cases instead of returning 1.
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch will create a reply queue pool for each MSI-X index and will
provide an array of base addresses instead of the single address of
legacy mode. Using this new interface the driver can support higher
queue depths through scattered DMA pools.

If array mode is not supported driver will fall back to the legacy
method of reply pool allocation. This limits controller queue depth to
1K max. To enable a queue depth of more than 1K driver requires firmware
to support array mode and scratch_pad3 will provide the new queue depth
value.

When RDPQ is used, downgrading to an older firmware release should not
be permitted. This may cause firmware fault and is not supported.
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Firmware will fill out per-LD data to tell driver whether a particular
LD supports region lock bypass. If yes, then driver will send non-FP
LDIO to region lock bypass FIFO. With this change in driver, firmware
will optimize certain code to improve performance.
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch will update device Queue depth based on interface type(SAS,
SATA..) for sysPDs.  For Virtual disks(VDs), there will be no change in
queue depth (will remain 256).  To fetch interface type (SAS or SATA or
FC..) of syspD, driver will send DCMD MR_DCMD_PD_GET_INFO.
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch adds task management for SCSI commands. Added functions are
task abort and target reset.

1. Currently, megaraid_sas driver performs controller reset when any IO
times out.  With task management support added, task abort and target
reset will be tried to recover timed out IO. If task management fails,
then controller reset will be performaned. If the task management
request times out, fail the request and escalate to the next
level (controller reset).

2. mr_device_priv_data will be allocated for all generations of
controller, but is_tm_capable flag will never be set for
controllers (prior to Invader series) as firmware support is not
available for task management.

3. Task management capable firmware will set is_tm_capable flag in
firmware API.
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch will do proper error handling for DCMD timeout failure cases
for Fusion adapters:

1. For MFI adapters, in case of DCMD timeout (DCMD which must return
SUCCESS) driver will call kill adapter.

2. What action needs to be taken in case of DCMD timeout is decided by
function dcmd_timeout_ocr_possible().  DCMD timeout causing OCR is
applicable to the following commands:

	MR_DCMD_PD_LIST_QUERY
	MR_DCMD_LD_GET_LIST
	MR_DCMD_LD_LIST_QUERY
	MR_DCMD_CTRL_SET_CRASH_DUMP_PARAMS
	MR_DCMD_SYSTEM_PD_MAP_GET_INFO
	MR_DCMD_LD_MAP_GET_INFO

3. If DCMD fails from driver init path there are certain DCMDs which
must return SUCCESS. If those DCMDs fail, driver bails out. For optional
DCMDs like pd_info etc., driver continues without executing certain
functionality.
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch will do synhronization between OCR function and AEN function
using "reset_mutex" lock.  reset_mutex will be acquired only in the
first half of the AEN function which issues a DCMD. Second half of the
function which calls SCSI API (scsi_add_device/scsi_remove_device)
should be out of reset_mutex to avoid deadlock between scsi_eh thread
and driver.

During chip reset (inside OCR function), there should not be any PCI
access and AEN function (which is called in delayed context) may be
firing DCMDs (doing PCI writes) when chip reset is happening in parallel
which will cause FW fault. This patch will solve the problem by making
AEN thread and OCR thread mutually exclusive.
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This adds the needed check after the call to the function
mraid_mm_alloc_kioc in order to make sure that this function has not
returned NULL and therefore makes sure we do not deference a NULL
pointer if one is returned by mraid_mm_alloc_kioc.  Further more add
needed comments explaining that this function call can return NULL if
the list head is empty for the pointer passed in order to allow furture
users to understand this required pointer check.
Signed-off-by: NNicholas Krause <xerofoify@gmail.com>
Acked-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch changes the !blk-mq path to the same defaults as the blk-mq
I/O path by always enabling block tagging, and always using host wide
tags.  We've had blk-mq available for a few releases so bugs with
this mode should have been ironed out, and this ensures we get better
coverage of over tagging setup over different configs.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NJens Axboe <axboe@kernel.dk>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The DELL PERC5 controller firmware does not list tape drives in response
to MR_DCMD_PD_LIST_QUERY. This causes tape drives not be exposed to the
OS when connected to a PERC5 controller.

This patch permits detection of tape drives connected to a PERC5
controller by exposing non-TYPE_DISK devices unconditionally.
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This is an issue on SMAP enabled CPUs and 32 bit apps running on 64 bit
OS. Do not access user memory from kernel code. The SMAP bit restricts
accessing user memory from kernel code.

Cc: <stable@vger.kernel.org>
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

It may happen (kdump), that an interrupt is invoked just after the
setup_irqs function was called but before the tasklet was initialised.
At this phase the hw ints should have been disabled, but for unknown
reason this mechanism seems to not work properly.

From: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Do not use PAGE_SIZE marco to calculate max_sectors per I/O
request. Driver code assumes PAGE_SIZE will be always 4096 which can
lead to wrongly calculated value if PAGE_SIZE is not 4096. This issue
was reported in Ubuntu Bugzilla Bug #1475166.

Cc: <stable@vger.kernel.org>
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Remove PCI id based checks and use instance->ctrl_context to decide
whether controller is MFI-based or a Fusion adapter. Additionally,
Fusion adapters are divided into two categories: Thunderbolt and
Invader.
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Expose non-disk (TAPE drive, CD-ROM) unconditionally.

Cc: <stable@vger.kernel.org>
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Some of these code changes were proposed by David Binderman.

Removed redudant check of requestorId. Redundant condition:
instance.requestorId. Check for plasma firmware 1.11 are now
restructured to support only specific device id.
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Syncro firmware supports round robin I/O switching on dual path. Driver
uses validHandles to check for dual path. However, it is supposed to
check for values > 1 (not > 2).
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Print firmware events in human-readable form. This will help users track
any critical firmware events without special application support.

Sample syslogd output:

megaraid_sas 0000:02:00.0: 8619 (491648347s/0x0020/WARN) - Controller temperature threshold exceeded. This may indicate inadequate system cooling. Switching to low performance mode.

The format of logged events is:

"<pci_dev_id>: <sequence_number> (<timestamp>/<locale>/<class>) - <description>"
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Fix the issue reported at:

	http://marc.info/?l=linux-scsi&m=143694494104544&w=2

Try to do chip reset at driver load time. If firmware fails to reach
ready state, try chip reset using adp_reset() callback. For Fusion
adapters the call back was previously void. Provide a suitable reset
function.
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Driver will expose max sge = 256 (earlier it was 64) if firmware
supports extended IO size (1M).
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NMartin Petersen <martin.petersen@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NMartin Petersen <martin.petersen@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Implemented JBOD map which will provide quick access for JBOD path and
also provide sequence number.  This will help hardware to fail command
to the FW in case of any sequence mismatch.

Fast Path I/O for JBOD will refer JBOD map (which has sequence number
per JBOD device) instead of RAID map.  Previously, the driver used RAID
map to get device handle for fast path I/O and this not have sequence
number information. Now, driver will use JBOD map instead.  As part of
error handling, if JBOD map is failed/not supported by firmware, driver
will continue using legacy behavior.

Now there will be three IO paths for JBOD (syspd):

 - JBOD map with sequence number (Fast Path)
 - RAID map without sequence number (Fast Path)
 - FW path via h/w exception queue deliberately setup devhandle
   0xFFFF (FW path).

Relevant data structures:

 - Driver send new DCMD MR_DCMD_SYSTEM_PD_MAP_GET_INFO for this purpose.
 - struct MR_PD_CFG_SEQ- This structure represent map of single physical
   device.
 - struct MR_PD_CFG_SEQ_NUM_SYNC- This structure represent whole JBOD
   map in general(size, count of sysPDs configured, struct MR_PD_CFG_SEQ
   of syspD with 0 index).
 - JBOD sequence map size is: sizeof(struct MR_PD_CFG_SEQ_NUM_SYNC)
   + (sizeof(struct MR_PD_CFG_SEQ) * (MAX_PHYSICAL_DEVICES - 1)) which
   is allocated while setting up JBOD map at driver load time.
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NMartin Petersen <martin.petersen@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NMartin Petersen <martin.petersen@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NMartin Petersen <martin.petersen@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Fix whitespace and indentation errors.  No code change.

[jejb: checkpatch fixes]
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Acked-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Use dev_printk() when possible to make messages more useful.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Acked-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>