Move the tuners one level up, as the "common" directory will be used
by drivers that are shared between more than one driver.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This standard is not properly documented, but its settings are at
the tda18271dd driver, and are somewhat obvious, as they follow
the same logic as DVB-T 7MHz.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

By default, tda18271 tries to optimize I2C bus by updating all registers
at the same time. Unfortunately, some devices doesn't support it.

The current logic has a problem when small_i2c is equal to 8, since there
are some transfers using 11 + 1 bytes.

Fix the problem by enforcing the max size at the right place, and allows
reducing it to max = 3 + 1.
Acked-by: NMichael Krufky <mkrufky@kernellabs.com>
Acked-by: NSri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There is already an option for sending 16 byte chunks rather that writing
39 bytes all at once during the tuner's initialization.  Some i2c buses
can't send 16 bytes at once, so create an option for sending 8 byte chunks.
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

For better readability, treat the low power standby mode configuration
as an output option feature configuration, and change it to a bitmask.

If left unconfigured, all features will remain enabled, just as the
default configuration was before these changes were introduced.
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add new standby mode:
TDA18271_STANDBY_LT_ON = slave tuner output loop thru on w/ xtal osc off
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

By default, the driver enters standby mode with slave tuner output
loop thru enabled and xtal oscillator on.

Not all designs require that slave tuner output loop thru and
xtal oscillator remain active while in standby mode, so two
additional standby modes have been added:

- standby mode with xtal oscillator on (loop thru off)

- total power off
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

On certain master / slave dual tuner configurations, tuning performance
improves when the RF tracking filter calibration is performed sequentially.

This patch allows for the bridge driver to specify this behavior in the
configuration structure at attach-time.

The "cal" module option will continue to override this attach-time
configuration: set cal=0 to prevent RF tracking filter calibration
on startup, and set cal=1 to force it.
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Reviewed-by: NSteven Toth <stoth@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The tda827x driver supports a feature that the tda18271 driver was lacking
until now.  This patch adds support for device-level configuration via the
tuner callback configuration interface.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

namespace for all of them.

There were several issues in the past, caused by the hybrid tuner design, since
now, the same tuner can be used by drivers/media/dvb and drivers/media/video.

Kconfig items were rearranged, to split V4L/DVB core from their drivers.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Acked-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

allow device-specific configuration of rf agc rf top and if top
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

All standard related configuration is stored within
struct tda18271_std_map_item.  Pass a pointer to this
structure rather than its individual members.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add attach-time parameter, "small_i2c" to limit i2c transfer size to write
at most 16 registers at a time during initialization.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Document debug level module options and
tda18271_config attach-time parameters.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Store IF Frequency in a u16 instead of a u32.  Multiply by 1000 before use.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Allow drivers to pass device-specific configuration parameters during attach.

If these parameters are omitted, default values will be used.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Move some common code to a new file to make this easier to look at.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

If we pass TDA18271_GATE_DIGITAL into tda18271_attach(), it will always try to
use the digital demodulator's i2c gate.

If we pass TDA18271_GATE_ANALOG into tda18271_attach(), it will always try to
use the analog demodulator's i2c gate.

If we pass TDA18271_GATE_AUTO into tda18271_attach(), it will try to use the
analog demodulator's i2c gate when tuning in analog mode, and it will try to
use the digital demodulator's i2c gate when tuning in digital mode.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add basic support for NXP TDA8295 analog demod and TDA18271 tuner silicon.

TDA8295 + TDA8275a not yet tested.
TDA8290 + TDA18271 not yet supported.

Digital mode of TDA18271 not yet tested & needs more work.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Reviewed-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Break tuner.ko into separate modules. This was a quick change -
Tuner sub-drivers are still static-linked to tuner.ko, this will
change after using dvb_attach and removing the probing functions.

After this change, one can deselect undesired tuner sub-drivers via Kconfig.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Acked-by: NHans Verkuil <hverkuil@xs4all.nl>
Acked-by: NMike Isely <isely@pobox.com>
Acked-by: NSteven Toth <stoth@hauppauge.com>
Acked-by: NPatrick Boettcher <pb@linuxtv.org>
Acked-by: NJarod Wilson <jwilson@redhat.com>
Acked-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Acked-by: NHans Verkuil <hverkuil@xs4all.nl>
Acked-by: NMike Isely <isely@pobox.com>
Acked-by: NSteven Toth <stoth@hauppauge.com>
Acked-by: NPatrick Boettcher <pb@linuxtv.org>
Acked-by: NJarod Wilson <jwilson@redhat.com>
Acked-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- Add new Typhoon DVB-T Cardbus.
- DVB-T support for MD7134 cardbus and the PCI variants
- initial DVB-T support for Lifeview Flydvb-t duo
- DVB-T support for Philips TOUGH reference design
- Don't turn off the xtal output of tda8274/75 in sleep mode
- Let Kconfig decide whether to include frontend-specific code in saa7134-dvb.
- Removed unused structures.
Signed-off-by: NJuergen Orschiedt <jorschiedt@web.de>
Signed-off-by: NMichael Krufky <mkrufky@m1k.net>
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!