- 19 9月, 2009 5 次提交
-
-
由 Michael Krufky 提交于
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Michael Krufky 提交于
For better readability, treat the low power standby mode configuration as an output option feature configuration, and change it to a bitmask. If left unconfigured, all features will remain enabled, just as the default configuration was before these changes were introduced. Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Michael Krufky 提交于
Add new standby mode: TDA18271_STANDBY_LT_ON = slave tuner output loop thru on w/ xtal osc off Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Michael Krufky 提交于
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Michael Krufky 提交于
By default, the driver enters standby mode with slave tuner output loop thru enabled and xtal oscillator on. Not all designs require that slave tuner output loop thru and xtal oscillator remain active while in standby mode, so two additional standby modes have been added: - standby mode with xtal oscillator on (loop thru off) - total power off Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
- 12 9月, 2009 19 次提交
-
-
由 Mauro Carvalho Chehab 提交于
Currently, V4L uses a scancode table whose index is the scancode and the value is the keycode. While this works, it has some drawbacks: 1) It requires that the scancode to be at the range 00-7f; 2) keycodes should be masked on 7 bits in order for it to work; 3) due to the 7 bits approach, sometimes it is not possible to replace the default keyboard to another one with a different encoding rule; 4) it is different than what is done with dvb-usb approach; 5) it requires a typedef for it to work. This is not a recommended Linux CodingStyle. This patch is part of a larger series of IR changes. It basically replaces the IR_KEYTAB_TYPE tables by a structured table: struct ir_scancode { u16 scancode; u32 keycode; }; This is very close to what dvb does. So, a further integration with DVB code will be easy. While we've changed the tables, for now, the IR keycode handling is still based on the old approach. The only notable effect is the redution of about 35% of the ir-common module size: text data bss dec hex filename 6721 29208 4 35933 8c5d old/ir-common.ko 5756 18040 4 23800 5cf8 new/ir-common.ko In thesis, we could be using above u8 for scancode, reducing even more the size of the module, but defining it as u16 is more convenient, since, on dvb, each scancode has up to 16 bits, and we currently have a few troubles with rc5, as their scancodes are defined with more than 8 bits. This patch itself shouldn't be doing any functional changes. Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mauro Carvalho Chehab 提交于
[mchehab@redhat.com: Fix a few wrong IR keymaps] Signed-off-by: NShine Liu <shinel@foxmail.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Michael Krufky 提交于
On certain master / slave dual tuner configurations, tuning performance improves when the RF tracking filter calibration is performed sequentially. This patch allows for the bridge driver to specify this behavior in the configuration structure at attach-time. The "cal" module option will continue to override this attach-time configuration: set cal=0 to prevent RF tracking filter calibration on startup, and set cal=1 to force it. Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com> Reviewed-by: NSteven Toth <stoth@kernellabs.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Michael Krufky 提交于
remove excess spacing from the tda_foo printk macros & line things up better Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Michael Krufky 提交于
Rename dprintk to tda_dprintk to be consistent with the other tda_foo macros. Move KERN_DEBUG facility level to tda_dprintk. Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Dmitri Belimov 提交于
Implement Philips FM1216MK5. 1. Implement get_stereo function. 2. Add correct data byte for FM radio mode Signed-off-by: NBeholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com> Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mauro Carvalho Chehab 提交于
KEY_CAMERA is already used for a long time with webcam drivers to take a picture. On other media drivers, due to the lack of a snapshot button, random KEY codes were sent, being KEY_SHUFFLE the most used one, probably due to cut-and-paste from other remotes, since one of them uses the same key for snapshot and shuffle. The better is to use KEY_CAMERA on all drivers solving this issue. This follows the IR standard map as defined at: http://linuxtv.org/wiki/index.php/Remote_ControllersSigned-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mauro Carvalho Chehab 提交于
Use standard definitions for channel controls, as defined at: http://linuxtv.org/wiki/index.php/Remote_Controllers While here, fix a few broken up/down/left/right mappings Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mauro Carvalho Chehab 提交于
Each remote were using a different keycode for timeshift. Use the same keycode for all of them, using the map as defined at: http://linuxtv.org/wiki/index.php/Remote_ControllersSigned-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mauro Carvalho Chehab 提交于
There are several IR's that were using IR to type a letter that it is known by some random application. Instead, the better is to use the standard definitions found at: http://linuxtv.org/wiki/index.php/Remote_Controllers And, if needed, submit a patch for the application to understand the media keys. Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mauro Carvalho Chehab 提交于
While we're still discussing it, let's point to the wiki page. In the future, this should be added at V4L2 API spec DocBooks. Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mauro Carvalho Chehab 提交于
This is needed to match the standard mapping defined at: http://linuxtv.org/wiki/index.php/Remote_Controllers#Remote_ControllersSigned-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mauro Carvalho Chehab 提交于
Make Checkpatch tool happy: -:2349: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable On all cases, it were just a blank line at the wrong place. Yet, fixing it is trivial Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mauro Carvalho Chehab 提交于
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mauro Carvalho Chehab 提交于
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mauro Carvalho Chehab 提交于
The ir-keymaps.c has frequent additions. As people tend to copy an old keyboard entry, a bad CodingStyle at an ancient entry may result on a freshly bad CodingStyle patch. So, better to fix the CodingStyle for the entire file. This patch is the first of a series of patches fixing it, generated by some perl magic plus manual handling. Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Igor M. Liplianin 提交于
Add Compro VideoMate S350 DVB-S driver. The card uses zl10313, zl10039, saa7130 integrated circuits. Signed-off-by: NIgor M. Liplianin <liplianin@me.by> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Devin Heitmueller 提交于
Add support for the remote control that comes with the Cinergy Hybrid T USB XS Thanks to Jelle de Jong for providing sample hardware to test with. Cc: Jelle de Jong <jelledejong@powercraft.nl> Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Andy Walls 提交于
Signed-off-by: NAndy Walls <awalls@radix.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
- 14 8月, 2009 2 次提交
-
-
由 Devin Heitmueller 提交于
A user discovered that the Geniatech x8000 encountered a regression when the xc3028 power management was introduced. The xc3028 never recovers after setting the powerdown register, which is probably because the xc3028 reset GPIO is not properly configured. Since I do not have access to the hardware and thus cannot determine the correct GPIO configuration, just disable xc3028 power management on this board, which fixes the regression. Thanks to user "ritec" for reporting the issue and testing the fix. Cc: rictec <rictec@netcabo.pt> Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jan Nikitenko 提交于
Fixes stack corruption bug present in dump_regs function of zl10353 and qt1010 drivers: the buffer buf was one byte smaller than required - there are 4 chars for address prefix, 16 * 3 chars for dump of 16 eeprom bytes per line and 1 byte for zero ending the string required, i.e. 53 bytes, but only 52 were provided. The one byte missing in stack based buffer buf can cause stack corruption possibly leading to kernel oops, as discovered originally with af9015 driver (af9015: fix stack corruption bug). Signed-off-by: NJan Nikitenko <jan.nikitenko@gmail.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
- 06 7月, 2009 1 次提交
-
-
由 Andy Walls 提交于
The following patch should fix 7 MHz DVB-T with the XC3028 using the DTV7 firmware from the xc3028-v27.fw firmware image. Tested-by: NTerry Wu <terrywu2009@gmail.com> [mchehab@redhat.com: thanks to John Ferlito, we have a real test in Australia] Signed-off-by: NAndy Walls <awalls@radix.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
- 23 6月, 2009 1 次提交
-
-
由 Devin Heitmueller 提交于
Add an IR profile for the EVGA inDtube remote control (which is an NEC type remote) Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
- 17 6月, 2009 12 次提交
-
-
由 Dmitri Belimov 提交于
Change order data of buffer in FM simple_tune function. It is usefull for: 1. Set data of tuner with CP bit UP. 0xCE for MK5 or 0xC6 for MK3 2. When call simple_fm_tune, read this byte from config and overwrite this byte in function simple_radio_bandswitch for set CP bit to OFF. Of course it can be usefull for other tuner for overwrite default settings of FM. Signed-off-by: NBeholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Andy Walls 提交于
Signed-off-by: NAndy Walls <awalls@radix.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mauro Carvalho Chehab 提交于
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mauro Carvalho Chehab 提交于
Both ATSC and DVB @ 6MHz bandwidth require the same offset. While we're fixing it, let's cleanup the bandwidth setup to better reflect the fact that it is a function of the bandwidth. Thanks to Terry Wu <terrywu2009@gmail.com> for pointing this issue and to Andy Walls <awalls@radix.net> for an initial patch for this fix. Cc: Terry Wu <terrywu2009@gmail.com> Acked-by: NAndy Walls <awalls@radix.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mauro Carvalho Chehab 提交于
The only two countries that are known to use 6MHz bandwidth are Taiwan and Uruguay. Both use QAM subcarriers at OFTM. This patch fixes the firmware load for such countries, where the required firmware is the QAM one. This also confirms the previous tests where it was noticed that the 6MHz QAM firmware doesn't work for cable. So, this patch also removes support for DVB-C, instead of just printing a warning. Thanks to Terry Wu <terrywu2009@gmail.com> for pointing this issue and to Andy Walls <awalls@radix.net> for an initial patch for this fix. Cc: Terry Wu <terrywu2009@gmail.com> Acked-by: NAndy Walls <awalls@radix.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Devin Heitmueller 提交于
Add copyright line for xc5000.c. Cc: Steven Toth <stoth@kernellabs.com> Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Devin Heitmueller 提交于
Instead of polling at 100ms intervals for register writes, poll at 5ms intervals. This is consistent with the xc5000 specification, and improves tuning time by up to 500 ms on devices that such as the au0828 which do not properly implement i2c clock stretching (since the five register writes that occur for a tuning request often do not complete immediately but do complete far before 100ms has gone by). The net amount of time we wait before timing out is unchanged (500ms). Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 David T.L. Wong 提交于
This patch adds XC5000 supports for DVB-T 6MHz and 8MHz bandwidth. Signed-off-by: NDavid T.L. Wong <davidtlwong@gmail.com> Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Devin Heitmueller 提交于
Xceive has graciously allowed us to now freely redistribute the xc5000 firmware, which eliminates the need for users to manually extract the blob from the Hauppauge driver. Thanks to Brian Mathews <bmathews@xceive.com> for providing this code Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Devin Heitmueller 提交于
There was a typo in the module description for the "no_poweroff" option, where the help was being associated with the "debug" option instead. Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Devin Heitmueller 提交于
Provide for the ability for a user to disable putting the tuner to sleep, in case he doesn't want to incur the cost of reloading the firmware when starting up his/her application. The module options are intentionally identical to xc3028. Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Devin Heitmueller 提交于
Make it a little more obvious in the dmesg output what is going on during firmware upload. This is more important for boards like the HVR-950q that take nearly seven seconds to do the upload. Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-