When cdev_add() failed there is no reason to call cdev_del().
Signed-off-by: NRolf Eike Beer <eike-kernel@sf-tec.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix the year check on setting the time with the S3C24XX RTC driver.  Also
move the debug to before the set to see what is going on if it does fail.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

On an nForce4-equipped machine with two SATA disk in raid1 setup using dmraid,
we experienced frequent deadlock of the system under high i/o load.  'cat
/dev/zero > ~/zero' was the most reliable way to reproduce them: Randomly
after a few GB, 'cp' would be left in 'D' state along with kjournald and
kmirrord.  The functions cp and kjournald were blocked in did vary, but
kmirrord's wchan always pointed to 'mempool_alloc()'.  We've seen this pattern
on 2.6.15 and 2.6.17 kernels.  http://lkml.org/lkml/2005/4/20/142 indicates
that this problem has been around even before.

So much for the facts, here's my interpretation: mempool_alloc() first tries
to atomically allocate the requested memory, or falls back to hand out
preallocated chunks from the mempool.  If both fail, it puts the calling
process (kmirrord in this case) on a private waitqueue until somebody refills
the pool.  Where the only 'somebody' is kmirrord itself, so we have a
deadlock.

I worked around this problem by falling back to a (blocking) kmalloc when
before kmirrord would have ended up on the waitqueue.  This defeats part of
the benefits of using the mempool, but at least keeps the system running.  And
it could be done with a two-line change.  Note that mempool_alloc() clears the
GFP_NOIO flag internally, and only uses it to decide whether to wait or return
an error if immediate allocation fails, so the attached patch doesn't change
behaviour in the non-deadlocking case.  Path is against current git
(2.6.18-rc4), but should apply to earlier versions as well.  I've tested on
2.6.15, where this patch makes the difference between random lockup and a
stable system.
Signed-off-by: NDaniel Kobras <kobras@linux.de>
Acked-by: NAlasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In the cleanups of drivers/rtc/s3c-rtc.c, the base address for the
registers got broken.  This patch fixes that by ensuring the readb/writeb
are all prefixed with the base returned from ioremap()ing the registers.

Also fix check for valid year range, which was the wrong way around.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The existing unusual_devs entry for the UCR-61S2B appears to have too
wide a revision range.  It matches at least one device that doesn't
respond to the initialization sequence.  Perhaps the sequence needs to
be updated, or perhaps something else can be done.  For now, this patch
(as764) restricts the range to include only the revision mentioned in
the original comment.

This resolves (for now!) Bugzilla entry #6950.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch removes support for a clone of Nokia DKU-5 cable made by Ours
Technology Inc, as it turned out that the cable does not use the pl2303
chip, but OTI-6858 chip which is not compatible with the pl2303.
Signed-off-by: NTomasz Kazmierczak <tomek.fizyk@op.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This was pointed out by Adrian Bunk <bunk@stusta.de>, as found by the Coverity Checker.

Cc: Adrian Bunk <bunk@stusta.de>
Cc: Oliver Bock <o.bock@fh-wolfenbuettel.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Removes an unused kerneldoc entry from pci_match_device and
put the others into correct order.
Signed-off-by: NHenrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Here is a patch against the CPCI hotplug core to fix up PCI resource
assignment such that things will actually work when a hot inserted
device is enabled.  I mentioned this patch to you way back in April at
ELC, but am only now out from under things enough to clean it up and
submit it.  I've basically cribbed the corresponding code from
shpchp_pci.c, so there are no big surprises.  If it's still possible, I
wouldn't mind this going into 2.6.18, but it wouldn't be the end of the
world if it went into 2.6.19.
Signed-off-by: NScott Murray <scottm@somanetworks.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- add the ICH6(R) LPC to the ICH6 ACPI quirks.  currently only the ICH6-M
  is handled.  [ PCI_DEVICE_ID_INTEL_ICH6_1 is the ICH6-M LPC, ICH6_0 is
  the ICH6(R) ]

- remove the wrong quirk calling asus_hides_smbus_lpc() for ICH6.  the
  register modified in asus_hides_smbus_lpc() has a different meaning in
  ICH6.
Signed-off-by: NDaniel Ritz <daniel.ritz@gmx.ch>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch contains 2 sets of fixes for the abituguru:
 1) Much improved timeout handling, drasticly reducing the amount of
    timeout errors on some motherboards
 2) Fix the exit paths in the bank1 sensor type detect code to always
    restore the original settings even on an error. Without this our
    special test settings could remain seriously confusing the system
    BIOS's setup menu.

Both are very much related and are must haves, to avoid messing up the
uguru CMOS settings.

Detailed changes:
- Much improved timeout / wait for status handling. Many thanks to Sunil
  Kumar, for all his testing, ideas and patches! The code now first busy
  waits, polling the uguru for the expected status as this usually
  succeeds pretty quickly (within 90 reads). To avoid unnecessary CPU burn
  in timeout conditions, the amount of busy waiting has been halved from
  previous versions (120 tries instead of 250). This is not a problem,
  because this version goes to sleep after 120 attemps for 1 jiffy and
  then tries again, it does this sleep and try again 5 times before
  finally giving up. This (almost?) completly removes the timeout errors
  some people have seen regulary. Apparently some older uguru versions
  sometimes are distracted for a (relatively) long time. This solves this.
- These timeout errors not only occur in the sending address part of
  reading the uguru but also in the wait for read state, so errors in
  this state are now handled as retryable just like send address state
  errors and are only logged and reported to userspace if 3 executive
  tries fail.
- Fix a very nasty bug in the bank1 sensor type detection code, where it
  would not restore the original settings in any of the error paths!
- Since not successfully restoring the original settings can seriously
  confuse the system BIOS (hang when entering the relevant setup menu),
  we now try restoring them 3 times before giving up.
Signed-off-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The tps65010.c driver in the main tree never got updated with
build fixes since the last batch of I2C driver changes; and the
genirq trigger flags were updated wierdly too.

This also includes a minor tweak to reduce the frequency used to
poll for unplug-the-AC-power on the TPS chips that don't provide
relevant IRQs.  It _would_ be nice to sense whether there's even
a battery, but that'd normally be an HDQ/1-wire interface to a
smart battery, and such APIs aren't standardized.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The callers of scsi_send_eh_cmnd are setting the cmnd buffer,
and then scsi_send_eh_cmnd is copying that updated buffer to
the old_cmnd variable. Then after the command runs, we end up
copying that old_cmnd var which has the new cmnd to the scsi
command buffer. When this command gets recent, all types of fun
things happen like getting TUR or START_STOP commands with
data and scatterlists.

This patch made against scsi-rc-fixes, has the callers of
scsi_send_eh_cmnd pass in the command so scsi_send_eh_cmnd
can do the right thing. This should go into 2.6.18 since this
fixes a regression added when we removed some of the scsi_cmnd
fields and replaced them with local variables.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Software must explicitely re-enable extended firmware tracing
after any ISP abort condition.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Original code attempts to retry PLOGIs to fcports that are
FCP_TARGETs only.  If the driver never performed a successful
PLOGI/PRLI, the port-type would never be assigned, and the
relogin logic would silently drop the request (and thus the port
would not be recognized and registered).

The fix is relatively straightforward, drop the FCP_TARGET-only
check.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

There's a problem where sg is executing a ->nopage operation on a
compound page, it actually calls get_page() on the first page in the
compound rather than the page which is being mapped.  The fix is to
select the correct page by indexing into the compound.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

The subsystem check in the PAV code is incorrect, it enables PAV
per device instead of per subsystem.
Signed-off-by: NHorst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

vt6420 has super-fragile SCR registers which can hang the whole
machine if accessed with the wrong timings.  This patch makes sata_via
use SCR registers only during probing and with the same timings as
before (pre new EH), which is proven to work.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch implements force_pcs module parameter for ata_piix.  If 1,
PCS is ignored, 2 honored.  As there seem to be quite a few ICHs w/
impaired PCS, this option will be useful for cases where the default
setting doesn't work.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

There have been a number of reports regarding some ICH5s failing to
detect devices since the PCS handling update.  Analysis shows that
these problems are caused by bogus PCS values from those controllers.

Before the PCS update, the driver didn't honor PCS regs exactly and
probed them in many cases PCS reports no device.  Now that PCS is
honored exactly, these hardware problems are visible.

This patch makes ICH5 ignore PCS.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

spectrum_cs: Fix the logic so we error when the device is *not* present!

This fixes firmware upload failures which prevent the driver from
working (the bug is also present in 2.6.17).
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

A change I made for 2.6.17 and another for 2.6.18 do not work on older
pcnet32 chips which I do not have access to.  If the chip is a 79C970 or
79C965, do not try and suspend or check the link status.
I have tested with a 79C970A, 79C971, 79C972, 79C973, 79C975, 79C976,
and 79C978.
Signed-off-by: NDon Fry <brazilnut@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

I am using a Xircom CEM33 pcmcia NIC which has occasional hardware problems.
If the netdev watchdog detects a transmit timeout, do_reset is called which
msleeps - this is illegal in atomic context.

This patch schedules the timeout handling as a workqueue item.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

while playing with gcc 4.1 -Wextra warnings, I came across this one:

drivers/net/3c515.c:1027: warning: comparison of unsigned expression >= 0 is always true

Since i is unsigned the >= 0 check in the for loop is always true,
so we might spin there forever unless the if condition triggers.
Since i is only used in this loop, this patch changes it to
an integer.
Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes yet another sunsab problem, when console is set to anything
but the first port. The console framework calls sunsab_console_setup
for each port, and we end up setting up a console on a not yet
discovered port, which leads to an Oops. Instead, defer console setup
until the requested port is properly initialized. Tested on an E250
through an RSC console.

Reported by Daniel Smolik <marvin@mydatex.cz>
Signed-off-by: NMarc Zyngier <maz@misterjones.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Noted by Alexey Dobriyan.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update the driver's list of HCA firmware revisions to make sure people
running Sinai firmware older than 1.1.0 get a message suggesting a
firmware upgrade.  Update the Arbel versions as well while we are at it.
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Intersil firmware 1.7.4 (and possibly others) loses the antenna
selection settings when the port is reset.
Signed-off-by: NDavid Acker <dacker@roinet.com>
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This bug was introduced during the PCMCIA API conversion and broke
spectrum_cs completely.

Tracked down by Fredrik Tolf <fredrik@dolda2000.com>
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Revert the superfluous initilization causing some mice become jumpy.
Signed-off-by: NPozsar Balazs <pozsy@uhulinux.hu>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Remove __initdata markings from keymaps as they are used during
normal driver operations.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This was introduced in commit 3d0f0fa0:
bounds checking is performed against period[32] while indexing delay[4].

Spotted by Coverity, CID 1376.
Signed-off-by: NFlorin Malita <fmalita@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Move out PCS handling from piix_sata_prereset() into
piix_sata_present_mask() and use it from newly implemented
piix_sata_softreset().  Class codes for devices which are indicated to
be absent by PCS are cleared to ATA_DEV_NONE.  This fixes ghost device
problem reported on ICH6 and 7.

This patch moves PCS handling from prereset to softreset, which makes
two behavior changes.

* perform softreset even when PCS indicates no device
* PCS handling is repeated before retrying softresets due to reset
  failures.

Both behavior changes are intended and more consistent with how other
drivers behave.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Hi,

One of my recent changes broke C101 carrier handling, this patch
fixes it. Also fixes an old TX underrun checking bug.

2.6.18 material. Please apply.
Thanks.
Signed-off-by: NKrzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch should update the fs_enet infrastructure to utilize Phy Abstraction
Layer subsystem.  Along with the above, there are apparent bugfixes, overhaul
and improvements.
Signed-off-by: NVitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This makes it possible for HW PHY-less boards to utilize PAL goodies.  Generic
routines to connect to fixed PHY are provided, as well as ability to specify
software callback that fills up link, speed, etc.  information into PHY
descriptor (the latter feature not tested so far).
Signed-off-by: NVitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Valerie Henson <val_henson@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

qeth: bhs must be disabled when accessing neighbour tables.

=================================
[ INFO: inconsistent lock state ]
Signed-off-by: NJeff Garzik <jeff@garzik.org>