This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: NArun Sharma <asharma@fb.com>
Reviewed-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Compile tested.
remove unnecessary code that matches this coccinelle pattern
	if (...)
		return ret;
	return ret;
Signed-off-by: NGreg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: NDavid S. Miller <davem@conan.davemloft.net>

The dp83640 PHY provides time stamp and other information via special
PHY status frames. Previously, the driver decoded the frames and then
let the network stack drop them. This works fine when the PTP messages
come over UDP.

However, when receiving PTP messages via L2 packets, this creates a
problem. The status frames use the official PTP destination MAC address,
and so they are delivered to user space along with the "real" frames,
causing confusion for applications.

This commit fixes the issue by simply dropping the PHY status frames
in the driver.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@conan.davemloft.net>

If two eternal time stamp events occur at nearly the same time, the
phyter will add an extra word into the status frame. This commit fixes
the parsing code to recognize and skip over the extra word.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@conan.davemloft.net>

This PHY is available integrated into BCM63xx series SOCs only.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 drivers/net/phy/Kconfig |    1 +
 1 files changed, 1 insertions(+), 0 deletions(-)
Acked-by: NFlorian Fainelli <ffainelli@freebox.fr>
Signed-off-by: NDavid S. Miller <davem@conan.davemloft.net>

If the dp83640 driver is not built as a module, the
MODULE_DEVICE_TABLE reference to dp83640_tbl nops out.

Since the table isn't referenced elsewhere, it it causes
the following warning:
drivers/net/phy/dp83640.c:1095: warning: ‘dp83640_tbl’ defined but not used

This apparently is common with mdio_device_id table structures,
and is avoided by using __maybe_unused annotation.
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

This patch adds support for the PTP clock found on the DP83640.
The basic clock operations and one external time stamp have
been implemented.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

This updates the network drivers so that they don't access the
ethtool_cmd::speed field directly, but use ethtool_cmd_speed()
instead.

For most of the drivers, these changes are purely cosmetic and don't
fix any problem, such as for those 1GbE/10GbE drivers that indirectly
call their own ethtool get_settings()/mii_ethtool_gset(). The changes
are meant to enforce code consistency and provide robustness with
future larger throughputs, at the expense of a few CPU cycles for each
ethtool operation.

All drivers compiled with make allyesconfig ion x86_64 have been
updated.

Tested: make allyesconfig on x86_64 + e1000e/bnx2x work
Signed-off-by: NDavid Decotigny <decot@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This makes sure the ethtool's set_settings() callback of network
drivers don't ignore the 16 most significant bits when ethtool calls
their set_settings().

All drivers compiled with make allyesconfig on x86_64 have been
updated.
Signed-off-by: NDavid Decotigny <decot@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

The function phy_attach_direct attaches the phy and calls phy_init_hw.
phy_init_hw can fail, but the phy is still marked as attached. Successive
calls to phy_attach_direct will fail because the phy is busy.

[    1.020000] eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1:00, irq=-1)
[    1.030000] eth1: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1:01, irq=-1)
[    2.050000] Sending DHCP requests .
[    3.020000] PHY: 1:00 - Link is Up - 100/Full
[    5.110000] ..... timed out!
[   87.660000] IP-Config: Reopening network devices...
[   88.190000] FEC: MDIO read timeout
[   88.190000] eth0: could not attach to PHY
[   88.190000] IP-Config: Failed to open eth0
[   88.210000] FEC: MDIO read timeout
[   88.210000] eth1: could not attach to PHY
[   88.210000] IP-Config: Failed to open eth1
[   88.220000] IP-Config: No network devices available.
[   88.220000] Freeing init memory: 6968K

[...]

starting network interfaces...
ip: RTNETLINK answers: File exists
[   94.000000] net eth0: PHY already attached
[   94.010000] eth0: could not attach to PHY
ip: SIOCSIFFLAGS: Device or resource busy

This patch adds phy_detach to clean up if phy_init_hw fails.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

phylib would silently ignore the phy_id argument to these ioctls and
perform the read/write with the active phydev address, whereas most
non-phylib drivers seem to allow access to all mdio addresses
(E.G. pcnet_cs).
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Get rid of users of of_platform_driver in drivers/net.  The
of_platform_{,un}register_driver functions are going away, so the
users need to be converted to using the platform_bus_type directly.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Platform code can now set the MICREL_PHY_50MHZ_CLK bit of dev_flags in a fixup
routine (registered with phy_register_fixup_for_uid()), to make the KZS8051RNL
PHY work with 50MHz RMII reference clock.

Cc: David J. Choi <david.choi@micrel.com>
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unneeded depends on PHYLIB.  The config selection is already in
an if PHYLIB / endif block.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the IC+ IP1001 (Gigabit Ethernet Transceiver) driver.
I've had to add an additional delay (2ns) to adjust RX clock phase at
GMII/ RGMII interface (according to the PHY data-sheet). This helps to
have the RGMII working on some ST platforms.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cc: netdev@vger.kernel.org
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some aspects of PHY initialization are board dependent, things like
indicator LED connections and some clocking modes cannot be determined
by probing.  The dev_flags element of struct phy_device can be used to
control these things if an appropriate value can be passed from the
Ethernet driver.  We run into problems however if the PHY connections
are specified by the device tree.  There is no way for the Ethernet
driver to know what flags it should pass.

If we are using the device tree, the struct phy_device will be
populated with the device tree node corresponding to the PHY, and we
can extract extra configuration information from there.

The next question is what should the format of that information be?
It is highly device specific, and the device tree representation
should not be tied to any arbitrary kernel defined constants.  A
straight forward representation is just to specify the exact bits that
should be set using the "marvell,reg-init" property:

      phy5: ethernet-phy@5 {
        reg = <5>;
        compatible = "marvell,88e1149r";
        marvell,reg-init =
                /* led[0]:1000, led[1]:100, led[2]:10, led[3]:tx */
                <3 0x10 0 0x5777>, /* Reg 3,16 <- 0x5777 */
                /* mix %:0, led[0123]:drive low off hiZ */
                <3 0x11 0 0x00aa>, /* Reg 3,17 <- 0x00aa */
                /* default blink periods. */
                <3 0x12 0 0x4105>, /* Reg 3,18 <- 0x4105 */
                /* led[4]:rx, led[5]:dplx, led[45]:drive low off hiZ */
                <3 0x13 0 0x0a60>; /* Reg 3,19 <- 0x0a60 */
      };

      phy6: ethernet-phy@6 {
        reg = <6>;
        compatible = "marvell,88e1118";
        marvell,reg-init =
                /* Fix rx and tx clock transition timing */
                <2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */
                /* Adjust LED drive. */
                <3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */
                /* irq, blink-activity, blink-link */
                <3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */
      };

The Marvell PHYs have a page select register at register 22 (0x16), we
can specify any register by its page and register number.  These are
the first and second word.  The third word contains a mask to be ANDed
with the existing register value, and the fourth word is ORed with the
result to yield the new register value.  The new marvell_of_reg_init
function leaves the page select register unchanged, so a call to it
can be dropped into the .config_init functions without unduly
affecting the state of the PHY.

If CONFIG_OF_MDIO is not set, there is no of_node, or no
"marvell,reg-init" property, the PHY initialization is unchanged.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 88E1149R is 10/100/1000 quad-gigabit Ethernet PHY.  The
.config_aneg function can be shared with 88E1118, but it needs its own
.config_init.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The definition of the Marvell PHY page register is not specific to
88E1121, so rename the macro to MII_MARVELL_PHY_PAGE, and use it
throughout.
Suggested-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The marvell 88ec048's official part number is 88e1318s.  This patch renames
definitions in the driver to reflect this.

In addition, a minor bug fix has been added to write back the MSCR1 register
value properly.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following functions are not used directly by any drivers:
    phy_attach_direct
    phy_device_create
    phy_prepare_link
    genphy_config_advert
    genphy_setup_forced
    phy_config_interrupt
    phy_clear_interrypt
    phy_sanitize_settings
    phy_enable_interrupts
    phy_disable_interrupts
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit c477d044 added support for RGMII
rx/tx delays except that it ends up clearing rx/tx delays bit for modes
differents that RGMII*ID. Due to this, ethernet is not working anymore
on my guruplug server +. This patch is fixing that.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The kernel doesn't have a symbol called BCM63XX.  There is a symbol
BCM63XX_ENET (introduced in 9b1fc55a, 6 weeks after 09bb9aa0 that
introduced BCM63XX_PHY), but the driver compiles without that, too.

Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MODULE_DEVICE_TABLE only expands to something if it's compiled
for a module.  So when building-in support for the phys, the
mdio_device_id tables are unused.  Marking them with __maybe_unused
fixes the following warnings:

	drivers/net/phy/bcm63xx.c:134: warning: 'bcm63xx_tbl' defined but not used
	drivers/net/phy/broadcom.c:933: warning: 'broadcom_tbl' defined but not used
	drivers/net/phy/cicada.c:162: warning: 'cicada_tbl' defined but not used
	drivers/net/phy/davicom.c:222: warning: 'davicom_tbl' defined but not used
	drivers/net/phy/et1011c.c:114: warning: 'et1011c_tbl' defined but not used
	drivers/net/phy/icplus.c:137: warning: 'icplus_tbl' defined but not used
	drivers/net/phy/lxt.c:226: warning: 'lxt_tbl' defined but not used
	drivers/net/phy/marvell.c:724: warning: 'marvell_tbl' defined but not used
	drivers/net/phy/micrel.c:234: warning: 'micrel_tbl' defined but not used
	drivers/net/phy/national.c:154: warning: 'ns_tbl' defined but not used
	drivers/net/phy/qsemi.c:141: warning: 'qs6612_tbl' defined but not used
	drivers/net/phy/realtek.c:82: warning: 'realtek_tbl' defined but not used
	drivers/net/phy/smsc.c:257: warning: 'smsc_tbl' defined but not used
	drivers/net/phy/ste10Xp.c:135: warning: 'ste10Xp_tbl' defined but not used
	drivers/net/phy/vitesse.c:195: warning: 'vitesse_tbl' defined but not used
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On resume, before starting the PAL state machine, check if the
adjust_link() method is well supplied. If not, this would lead to a
NULL pointer dereference in the phy_state_machine() function.

This scenario can happen if the Ethernet driver call manually the PHY
functions instead of using the PAL state machine. The mv643xx_eth driver
is a such example.
Signed-off-by: NSimon Guinot <sguinot@lacie.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is possible that phylib will call adjust_link before returning
from {,of_}phy_connect(), which may cause the following [very rare,
though] oops upon reopening the device:

  Unable to handle kernel paging request for data at address 0x0000024c
  Oops: Kernel access of bad area, sig: 11 [#1]
  PREEMPT SMP NR_CPUS=2 LTT NESTING LEVEL : 0
  P1021 RDB
  Modules linked in:
  NIP: c0345dac LR: c0345dac CTR: c0345d84
  TASK = dffab6b0[30] 'events/0' THREAD: c0d24000 CPU: 0
  [...]
  NIP [c0345dac] adjust_link+0x28/0x19c
  LR [c0345dac] adjust_link+0x28/0x19c
  Call Trace:
  [c0d25f00] [000045e1] 0x45e1 (unreliable)
  [c0d25f30] [c036c158] phy_state_machine+0x3ac/0x554
  [...]

Here is why. Drivers store phydev in their private structures, e.g.
gianfar driver:

static int init_phy(struct net_device *dev)
{
	...
	priv->phydev = of_phy_connect(...);
	...
}

So that adjust_link could retrieve it back:

static void adjust_link(struct net_device *dev)
{
	...
	struct phy_device *phydev = priv->phydev;
	...
}

If the device has been opened before, then phydev->state is set to
PHY_HALTED (or undefined if the driver didn't call phy_stop()).

Now, phy_connect starts the PHY state machine before returning phydev to
the driver:

	phy_start_machine(phydev, NULL);

	if (phydev->irq > 0)
		phy_start_interrupts(phydev);

	return phydev;

The time between 'phy_start_machine()' and 'return phydev' is undefined.
The start machine routine delays execution for 1 second, which is enough
for most cases. But under heavy load, or if you're unlucky, it is quite
possible that PHY state machine will execute before phy_connect()
returns, and so adjust_link callback will try to dereference phydev,
which is not yet ready.

To fix the issue, simply initialize the PHY's state to PHY_READY during
phy_attach(). This will ensure that phylib won't call adjust_link before
phy_start().
Signed-off-by: NAnton Vorontsov <avorontsov@mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several gigabit network drivers (SB1250_MAC, TIGON3, FSL, GIANFAR,
UCC_GETH, MV643XX_ETH, XILINX_LL_TEMAC, S6GMAC, STMMAC_ETH, PASEMI_MAC,
and OCTEON_ETHERNET) select PHYLIB.  These drivers are not under
NET_ETHERNET (10/100 mbit), so this warning is generated (long, irrelevant
parts are omitted):

warning: (NET_DSA && NET && EXPERIMENTAL && NET_ETHERNET && !S390 || ... || SB1250_MAC && NETDEVICES && NETDEV_1000 && SIBYTE_SB1xxx_SOC || TIGON3 && NETDEVICES && NETDEV_1000 && PCI || FSL_PQ_MDIO && NETDEVICES && NETDEV_1000 && FSL_SOC || GIANFAR && NETDEVICES && NETDEV_1000 && FSL_SOC || UCC_GETH && NETDEVICES && NETDEV_1000 && QUICC_ENGINE || MV643XX_ETH && NETDEVICES && NETDEV_1000 && (MV64X60 || PPC32 || PLAT_ORION) || XILINX_LL_TEMAC && NETDEVICES && NETDEV_1000 && (PPC || MICROBLAZE) || S6GMAC && NETDEVICES && NETDEV_1000 && XTENSA_VARIANT_S6000 || STMMAC_ETH && NETDEV_1000 && NETDEVICES && CPU_SUBTYPE_ST40 || PASEMI_MAC && NETDEVICES && NETDEV_10000 && PPC_PASEMI && PCI || OCTEON_ETHERNET && STAGING && !STAGING_EXCLUDE_BUILD && CPU_CAVIUM_OCTEON) selects PHYLIB which has unmet direct dependencies (!S390 && NET_ETHERNET)

PHYLIB is used by non-10/100 mbit ethernet drivers, so change the dependencies
to be NETDEVICES instead of NET_ETHERNET.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix phy.c kernel-doc notation:

Warning(drivers/net/phy/phy.c:313): No description found for parameter 'ifr'
Warning(drivers/net/phy/phy.c:313): Excess function parameter 'mii_data' description in 'phy_mii_ioctl'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

of_device is just an alias for platform_device, so remove it entirely.  Also
replace to_of_device() with to_platform_device() and update comment blocks.

This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.

@@
@@
-struct of_device
+struct platform_device
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Reviewed-by: NDavid S. Miller <davem@davemloft.net>

Marvell 88ec048 is a derivative of its 88e1121r device.  From the programmer's
perspective, the one major difference is the addition of an additional control
bit in Page 2 Register 16 - used to control the padding of odd nibble
preambles.

This patch adds support for this new device, while inheriting as much code as
possible from the existing 88e1121r implementation.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for RGMII RX/TX delay configuration on marvell 88e1121
and derivatives.  With this patch, PHY_INTERFACE_MODE_RGMII_*ID modes are now
supported on these devices.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new networking option to allow hardware time stamps
from PHY devices. When enabled, likely candidates among incoming and
outgoing network packets are offered to the PHY driver for possible
time stamping. When accepted by the PHY driver, incoming packets are
deferred for later delivery by the driver.

The patch also adds phylib driver methods for the SIOCSHWTSTAMP ioctl
and callbacks for transmit and receive time stamping. Drivers may
optionally implement these functions.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The phy_mii_ioctl() function unnecessarily throws away the original ifreq.
We need access to the ifreq in order to support PHYs that can perform
hardware time stamping.

Two maverick drivers filter the ioctl commands passed to phy_mii_ioctl().
This is unnecessary since phylib will check the command in any case.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This moves the various known Marvell PHY IDs to include/linux/marvell_phy.h
along with dev_flags definitions for use by the driver.

I then added a flag that changes the PHY init code to setup the LEDs
config to the values needed to operate a dns323 rev C1 NAS.

I moved the existing "resistance" flag to the .h as well, though I've
been unable to find whoever sets this to convert it to use that constant.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

Hello all:

This patch fixes what Ben mentioned, namely duplicated ids.

From: David J. Choi <david.choi@micrel.com>

Body of the explanation: This patch has changes as followings;
 -support the interrupt from phy devices from Micrel Inc.
 -support more phy devices, ks8737, ks8721, ks8041, ks8051 from Micrel.
 -remove vsc8201 because this device was used only internal test at Micrel.
Signed-off-by: NDavid J. Choi <david.choi@micrel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We started getting:

WARNING: vmlinux.o(.data+0x20bd0): Section mismatch in reference from
the variable octeon_mdiobus_driver to the function
.init.text:octeon_mdiobus_probe()

This fixes it.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit e13647c1 (phylib: Add support for the LXT973 phy.) added a new ID
but neglected to also add it to the MODULE_DEVICE_TABLE.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the 5241 PHY ID to the broadcom module.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>