In order to support the use of build_skb going forward it will be necessary
to place a maximum limit on the amount of data we can receive when jumbo
frames is not enabled.  In order to do this I am adding a new upper limit
for receive based on the size of a 2K buffer minus padding.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In the case of the Tx rings we need to only clear the Tx buffer_info when
we are resetting the rings.  Ideally we do this when we configure the ring
to bring it back up instead of when we are taking it down in order to avoid
dirtying pages we don't need to.

In addition we don't need to clear the Tx descriptor ring since we will
fully repopulate it when we begin transmitting frames and next_to_watch can
be cleared to prevent the ring from being cleaned beyond that point instead
of needing to touch anything in the Tx descriptor ring.

Finally with these changes we can avoid having to reset the skb member of
the Tx buffer_info structure in the cleanup path since the skb will always
be associated with the first buffer which has next_to_watch set.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since we are already using DMA attributes in igb for Rx there is no reason
why we can't also apply DMA_ATTR_WEAK_ORDERING which is needed on some
platforms to improve performance.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update the driver code so that we do bulk updates of the page reference
count instead of just incrementing it by one reference at a time.  The
advantage to doing this is that we cut down on atomic operations and
this in turn should give us a slight improvement in cycles per packet.
In addition if we eventually move this over to using build_skb the gains
will be more noticeable.

Link: http://lkml.kernel.org/r/20161110113616.76501.17072.stgit@ahduyck-blue-test.jf.intel.comSigned-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Cc: Helge Deller <deller@gmx.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Keguang Zhang <keguang.zhang@gmail.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When a reset occurs, the PPS SYS_WRAP interrupt was not re-enabled which
resulted in disabling of the PPS signaling. Fix this by recording when
the interrupt is on and ensuring that we re-enable it every time we
reset.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to allow for RX network flow classification to insert
and remove VLAN priority filter by ethtool

Example:
Add an VLAN priority filter:
$ ethtool -N eth0 flow-type ether vlan 0x6000 vlan-mask 0x1FFF action 2 loc 1

Show all filters:
$ ethtool -n eth0
4 RX rings available
Total 1 rules

Filter: 1
	Flow Type: Raw Ethernet
	Src MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
	Dest MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
	Ethertype: 0x0 mask: 0xFFFF
	VLAN EtherType: 0x0 mask: 0xffff
	VLAN: 0x6000 mask: 0x1fff
	User-defined: 0x0 mask: 0xffffffffffffffff
	Action: Direct to queue 2

Delete the filter by location:
$ ethtool -N delete 1
Signed-off-by: NRuhao Gao <ruhao.gao@ni.com>
Signed-off-by: NGangfeng Huang <gangfeng.huang@ni.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to allow for RX network flow classification to insert
and remove ethertype filter by ethtool

Example:
Add an ethertype filter:
$ ethtool -N eth0 flow-type ether proto 0x88F8 action 2

Show all filters:
$ ethtool -n eth0
4 RX rings available
Total 1 rules

Filter: 15
	Flow Type: Raw Ethernet
	Src MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
	Dest MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
	Ethertype: 0x88F8 mask: 0x0
	Action: Direct to queue 2

Delete the filter by location:
$ ethtool -N delete 15
Signed-off-by: NRuhao Gao <ruhao.gao@ni.com>
Signed-off-by: NGangfeng Huang <gangfeng.huang@ni.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to allow for RX network flow classification to insert
and remove Rx filter by ethtool. Ethtool interface has it's own rules
manager

Show all filters:
$ ethtool -n eth0
4 RX rings available
Total 2 rules
Signed-off-by: NRuhao Gao <ruhao.gao@ni.com>
Signed-off-by: NGangfeng Huang <gangfeng.huang@ni.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make igb_ptp_stop take advantage of this new function to reduce code
duplication.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Don't continue to use complex MAC type checks for handling various cases
where we have overflow check code. Make this code more obvious by
introducing a flag which is enabled for hardware that needs these
checks.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Upcoming patches will introduce new PTP specific flags. To avoid
cluttering the normal flags variable, introduce PTP specific "ptp_flags"
variable for this purpose, and move IGB_FLAG_PTP to become
IGB_PTP_ENABLED.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Table 7-62 on page 338 of the i210 datasheet lists TX and RX latencies
for the various speeds the chip supports.  To give better PTP timestamp
accuracy, adjust the timestamps by the amounts Intel gives based on
current link speed.
Signed-off-by: NNathan Sullivan <nathan.sullivan@ni.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For bitshifts, we should make use of the BIT macro when possible, and
ensure that other bitshifts are marked as unsigned. This helps prevent
signed bitshift errors, and ensures similar style.

Make use of GENMASK and the unsigned postfix where BIT() isn't
appropriate.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change fixes things so that we can fully support SR-IOV or the
recently added NTUPLE filtering while allowing support for VLAN promiscuous
mode.  By making this change we are able to support possible scenarios such
as SR-IOV with the PF connected to a Linux bridge hosting other VMs.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The RLPML registers already take the size of VLAN headers into account when
determining the maximum packet length.  This is called out in EAS documents
for several parts including the 82576 and the i350.  As such we can drop
the addition of size to the value programmed into the RLPML registers.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

I've got a startech thunderbolt dock someone loaned me, which among other
things, has the following device in it:

08:00.0 Ethernet controller: Intel Corporation I210 Gigabit Network Connection (rev 03)

This hotplugs just fine (kernel 4.2.0 plus a patch or two here):

[  863.020315] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.2.18-k
[  863.020316] igb: Copyright (c) 2007-2014 Intel Corporation.
[  863.028657] igb 0000:08:00.0: enabling device (0000 -> 0002)
[  863.062089] igb 0000:08:00.0: added PHC on eth0
[  863.062090] igb 0000:08:00.0: Intel(R) Gigabit Ethernet Network Connection
[  863.062091] igb 0000:08:00.0: eth0: (PCIe:2.5Gb/s:Width x1) e8:ea:6a:00:1b:2a
[  863.062194] igb 0000:08:00.0: eth0: PBA No: 000200-000
[  863.062196] igb 0000:08:00.0: Using MSI-X interrupts. 4 rx queue(s), 4 tx queue(s)
[  863.064889] igb 0000:08:00.0 enp8s0: renamed from eth0

But disconnecting it is another story:

[ 1002.807932] igb 0000:08:00.0: removed PHC on enp8s0
[ 1002.807944] igb 0000:08:00.0 enp8s0: PCIe link lost, device now detached
[ 1003.341141] ------------[ cut here ]------------
[ 1003.341148] WARNING: CPU: 0 PID: 199 at lib/iomap.c:43 bad_io_access+0x38/0x40()
[ 1003.341149] Bad IO access at port 0x0 ()
[ 1003.342767] Modules linked in: snd_usb_audio snd_usbmidi_lib snd_rawmidi igb dca firewire_ohci firewire_core crc_itu_t rfcomm ctr ccm arc4 iwlmvm mac80211 fuse xt_CHECKSUM ipt_MASQUERADE
nf_nat_masquerade_ipv4 tun ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 ipt_REJECT nf_reject_ipv4 xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat
nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat
nf_conntrack iptable_mangle iptable_security iptable_raw iptable_filter bnep dm_mirror dm_region_hash dm_log dm_mod coretemp x86_pkg_temp_thermal intel_powerclamp kvm_intel snd_hda_codec_hdmi kvm
crct10dif_pclmul crc32_pclmul ghash_clmulni_intel drbg
[ 1003.342793]  ansi_cprng aesni_intel hp_wmi aes_x86_64 iTCO_wdt lrw iTCO_vendor_support ppdev gf128mul sparse_keymap glue_helper ablk_helper cryptd snd_hda_codec_realtek snd_hda_codec_generic
microcode snd_hda_intel uvcvideo iwlwifi snd_hda_codec videobuf2_vmalloc videobuf2_memops snd_hda_core videobuf2_core snd_hwdep btusb v4l2_common btrtl snd_seq btbcm btintel videodev cfg80211
snd_seq_device rtsx_pci_ms bluetooth pcspkr input_leds i2c_i801 media parport_pc memstick rfkill sg lpc_ich snd_pcm 8250_fintek parport joydev snd_timer snd soundcore hp_accel ie31200_edac
mei_me lis3lv02d edac_core input_polldev mei hp_wireless shpchp tpm_infineon sch_fq_codel nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables autofs4 xfs libcrc32c sd_mod sr_mod cdrom
rtsx_pci_sdmmc mmc_core crc32c_intel serio_raw rtsx_pci
[ 1003.342822]  nouveau ahci libahci mxm_wmi e1000e xhci_pci hwmon ptp drm_kms_helper pps_core xhci_hcd ttm wmi video ipv6
[ 1003.342839] CPU: 0 PID: 199 Comm: kworker/0:2 Not tainted 4.2.0-2.el7_UNSUPPORTED.x86_64 #1
[ 1003.342840] Hardware name: Hewlett-Packard HP ZBook 15 G2/2253, BIOS M70 Ver. 01.07 02/26/2015
[ 1003.342843] Workqueue: pciehp-3 pciehp_power_thread
[ 1003.342844]  ffffffff81a90655 ffff8804866d3b48 ffffffff8164763a 0000000000000000
[ 1003.342846]  ffff8804866d3b98 ffff8804866d3b88 ffffffff8107134a ffff8804866d3b88
[ 1003.342847]  ffff880486f46000 ffff88046c8a8000 ffff880486f46840 ffff88046c8a8098
[ 1003.342848] Call Trace:
[ 1003.342852]  [<ffffffff8164763a>] dump_stack+0x45/0x57
[ 1003.342855]  [<ffffffff8107134a>] warn_slowpath_common+0x8a/0xc0
[ 1003.342857]  [<ffffffff810713c6>] warn_slowpath_fmt+0x46/0x50
[ 1003.342859]  [<ffffffff8133719e>] ? pci_disable_msix+0x3e/0x50
[ 1003.342860]  [<ffffffff812f6328>] bad_io_access+0x38/0x40
[ 1003.342861]  [<ffffffff812f6567>] pci_iounmap+0x27/0x40
[ 1003.342865]  [<ffffffffa0b728d7>] igb_remove+0xc7/0x160 [igb]
[ 1003.342867]  [<ffffffff8132189f>] pci_device_remove+0x3f/0xc0
[ 1003.342869]  [<ffffffff81433426>] __device_release_driver+0x96/0x130
[ 1003.342870]  [<ffffffff814334e3>] device_release_driver+0x23/0x30
[ 1003.342871]  [<ffffffff8131b404>] pci_stop_bus_device+0x94/0xa0
[ 1003.342872]  [<ffffffff8131b3ad>] pci_stop_bus_device+0x3d/0xa0
[ 1003.342873]  [<ffffffff8131b3ad>] pci_stop_bus_device+0x3d/0xa0
[ 1003.342874]  [<ffffffff8131b516>] pci_stop_and_remove_bus_device+0x16/0x30
[ 1003.342876]  [<ffffffff81333f5b>] pciehp_unconfigure_device+0x9b/0x180
[ 1003.342877]  [<ffffffff81333a73>] pciehp_disable_slot+0x43/0xb0
[ 1003.342878]  [<ffffffff81333b6d>] pciehp_power_thread+0x8d/0xb0
[ 1003.342885]  [<ffffffff810881b2>] process_one_work+0x152/0x3d0
[ 1003.342886]  [<ffffffff8108854a>] worker_thread+0x11a/0x460
[ 1003.342887]  [<ffffffff81088430>] ? process_one_work+0x3d0/0x3d0
[ 1003.342890]  [<ffffffff8108ddd9>] kthread+0xc9/0xe0
[ 1003.342891]  [<ffffffff8108dd10>] ? kthread_create_on_node+0x180/0x180
[ 1003.342893]  [<ffffffff8164e29f>] ret_from_fork+0x3f/0x70
[ 1003.342894]  [<ffffffff8108dd10>] ? kthread_create_on_node+0x180/0x180
[ 1003.342895] ---[ end trace 65a77e06d5aa9358 ]---

Upon looking at the igb driver, I see that igb_rd32() attempted to read from
hw_addr and failed, so it set hw->hw_addr to NULL and spit out the message
in the log output above, "PCIe link lost, device now detached".

Well, now that hw_addr is NULL, the attempt to call pci_iounmap is obviously
not going to go well. As suggested by Mark Rustad, do something similar to
what ixgbe does, and save a copy of hw_addr as adapter->io_addr, so we can
still call pci_iounmap on it on teardown. Additionally, for consistency,
make the pci_iomap call assignment directly to io_addr, so map and unmap
match.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We want to deprecate the use of 'struct timespec' on 32-bit
architectures, as it is will overflow in 2038. The igb
driver uses it to read the current time, and can simply
be changed to use ktime_get_real_ts64() instead.

Because of hardware limitations, there is still an overflow
in year 2106, which we cannot really avoid, but this documents
the overflow.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Reviewed-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When initializing igb driver (e.g. 82576, I350), IGB_FLAG_QUEUE_PAIRS is
set if adapter->rss_queues exceeds half of max_rss_queues in
igb_init_queue_configuration().
On the other hand, IGB_FLAG_QUEUE_PAIRS is not set even if the number of
queues exceeds half of max_combined in igb_set_channels() when changing
the number of queues by "ethtool -L".
In this case, if numvecs is larger than MAX_MSIX_ENTRIES (10), the size
of adapter->msix_entries[], an overflow can occur in
igb_set_interrupt_capability(), which in turn leads to an oops.

Fix this problem as follows:
 - When changing the number of queues by "ethtool -L", set
   IGB_FLAG_QUEUE_PAIRS in the same way as initializing igb driver.
 - When increasing the size of q_vector, reallocate it appropriately.
   (With IGB_FLAG_QUEUE_PAIRS set, the size of q_vector gets larger.)

Another possible way to fix this problem is to cap the queues at its
initial number, which is the number of the initial online cpus. But this
is not the optimal way because we cannot increase queues when another
cpu becomes online.

Note that before commit cd14ef54 ("igb: Change to use statically
allocated array for MSIx entries"), this problem did not cause oops
but just made the number of queues become 1 because of entering msi_only
mode in igb_set_interrupt_capability().

Fixes: 907b7835 ("igb: Add ethtool support to configure number of channels")
CC: stable <stable@vger.kernel.org>
Signed-off-by: NShota Suzuki <suzuki_shota_t3@lab.ntt.co.jp>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The i210 device offers a number of special PTP Hardware Clock features on
the Software Defined Pins (SDPs). This patch adds support for two of the
possible functions, namely time stamping external events, and periodic
output signals.

The assignment of PHC functions to the four SDP can be freely chosen by
the user.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The timecounter code has almost nothing to do with the clocksource
code. Let it live in its own file. This will help isolate the
timecounter users from the clocksource users in the source tree.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove a source of latency spikes (in my case up to 10ms) by not calling
code that uses mdelay() for feeding a phy statistic (rx errors for idle
symbols - not data -> idle_errors) while being called with a spinlock held.

As idle_errors isn't read, this patch only removes unused code and data.

Later, more complicated changes may be applied to address the spinlock and
allow for some PHY diagnostics by harvesting this PHY stats register fully.

This patch is designed to fix the issue and be safe for longterm/stable.

For the Intel e1000e driver, the same change was applied in 2008 with
commit 23033fad ("e1000e: remove phy read from inside spinlock").

The mdelay is triggered by HW/SW semaphores, thus it depends on the HW.

I've HW that triggers it even when idle. Others may trigger it only e.g.
when Ethernet ports aquire or loose the link or on ifconfig up / down.
We've noticed this first from delays in frame rx/tx due to the mdelay().

Example command for checking if the issue is triggered: cyclictest -Smp1
(Look for occasional "Max:" values > 4000 or use -b 4000 to stop if greater)

It was observed with I350 ports connected to other I350 ports, but not
if driver and EEPROM was modified to run the I350 in EEPROM-less mode.

phy_stats.idle_errors and .receive_errors (isn't touched) occupy 64 not
used bits in the adapter struct: Their allocation may be removed as well.

Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Todd Fujinaka <todd.fujinaka@intel.com>
Fixes: 12dcd86b ("igb: fix stats handling") (this added the spin_lock)
Signed-off-by: NBernhard Kaindl <bk-linux@use.startmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes WARNING:NETWORKING_BLOCK_COMMENT_STYLE from checkpatch file check.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes WARNING:LEADING_SPACE, WARNING:SPACING, ERROR:SPACING,
WARNING:SPACE_BEFORE_TAB and ERROR_CODE_INDENT from checkpatch file check.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

last_rx_timestamp should be updated only when rx time stamp is
read. Also it's only used with NICs that have per-interface time
stamping resources so it can be moved to adapter structure and
set in igb_ptp_rx_rgtstamp().
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Acked-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

igb has a single set of TX time stamping resources per NIC.
Use a simple bit lock to avoid race conditions and leaking skbs
when multiple TX rings try to claim time stamping.
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for the SIOCGHWTSTAMP ioctl which enables user
processes to read the current hwtstamp_config settings
non-destructively. Previously a process had to be privileged and could
only set values, it couldn't return what is currently set without
possibly overwriting the value.

This patch adds support for this new operation into igb by keeping a
shadow copy of the config in the adapter structure, which is returned
upon request.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Acked-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a problem where using ethtool for EEE setting was not
working correctly.  This patch also fixes a problem where
the function that checks for EEE status on i354 devices was not being
called and was causing warnings with static analysis tools.
Reported-by: NRashika Kheria <rashika.kheria@gmail.com>
Reported-by: NJosh Triplett <josh@joshtriplett.org>
Reported-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch updates the license text to remove address of Free Software
Foundation and refer  users to www.gnu.org instead. This patch also updates
the copyright dates in appropriate igb driver files.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on Stephen Hemminger's original patch.
Make local functions static, and remove unused functions.
Reported-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes how the driver initializes MSIx and checks
for MSIx configuration.  This change makes it easier to reconfigure the
device when queue changes happen at runtime using ethtool's set_channels
feature.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Simplify the code. Attach hwmon sysfs attributes to hwmon device
instead of pci device. Avoid race conditions caused by attributes
being created after registration and provide mandatory 'name'
attribute by using new hwmon API.

Other cleanup:

Instead of allocating memory for hwmon attributes, move attributes
and all other hwmon related data into struct hwmon_buff and allocate
the entire structure using devm_kzalloc.

Check return value from calls to igb_add_hwmon_attr() one by one instead
of logically combining them all together.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for the hardware feature Media Auto Sense.  This
feature requires a custom EEPROM image provided by our customer support
team.  The feature allows hardware designed with dual PHY's, fiber and
copper to be used with either media without additional EEPROM changes.
Fiber is preferred and driver will swap and configure for fiber media if
sensed by the device at any time. Device will swap back to copper if it
is the only media detected.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a new feature which is supported in some PHY's on some i354
devices.  This feature is Auto Media Detect and allows which ever media is
detected first by the PHY to be the media used and configured by the
device.  This is a media swapping feature that is wholly contained in the
Marvell PHY.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds the ethtool callbacks necessary to configure the
number of RSS queues.

The maximum number of queues is in accordance with the datasheets.
Signed-off-by: NLaura Mihaela Vasilescu <laura.vasilescu@rosedu.org>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are a mix of function prototypes with and without extern
in the kernel sources.  Standardize on not using extern for
function prototypes.

Function prototypes don't need to be written with extern.
extern is assumed by the compiler.  Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: NJoe Perches <joe@perches.com>

This patch adds 1 sec delay mechanism to i210 device family, in order
to avoid erroneous link issue with the link partner.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds the ethtool callbacks necessary to change the RETA
indirection table from userspace.

In order to achieve this, we add the indirection table field (rss_indir_tbl)
in the board specific data structure (struct igb_adapter) to preserve the
values across hardware resets.

The indirection table must be initialized with default values in the
following cases:
	* at module init time
	* when the number of RX queues changes.
For this reason we add a new field (rss_indir_tbl_init) in igb_adapter
that keeps track of the number of RX queues. Whenever the number of RX
queues changes, the rss_indir_tbl is modified and initialized with default
values. The rss_indir_tbl_init is updated accordingly.

CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NLaura Mihaela Vasilescu <laura.vasilescu@rosedu.org>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

RETA indirection table is used to assign the received data to a CPU
in order to maintain an efficient distribution of network receive
processing across multiple CPUs.

This patch removes the hard-coded value for the size of the indirection
table and defines a new macro.
Signed-off-by: NLaura Mihaela Vasilescu <laura.vasilescu@rosedu.org>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes unused i2c function definition.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>