Add code to display the detected PCI-E bus width.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

When powering down the PHY (if WoL is disabled) we should only check
copper PHY's and handle PCI-E adapters differently.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Several hardware bits were set all over the driver and have been
consolidated into a single function.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Disable jumbo frames for 82573L alltogether and when ASPM is enabled
since the hardware has problems with it. For the NICs that do support
this in the 82573 series we set ERT_2048 to attempt to receive as much
traffic as early as we can.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Several manageability capability detection parts hinted towards
our code being incomplete for PCI-E. According to spec, we do not
want to poke any MANC bits at all.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

With a patch, ethtool can now signify the driver to advertise more
than just a single speed/duplex setting. This allows you to tell the
card to advertise in 10/100 in any speed if you don't have a gigabit
switch for instance.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Add 4 multicast and broadcast hardware counters (rx/tx), and eliminate
as many non-hardware counters as possible.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Signed-off-by: NNicholas Nunley <nicholas.d.nunley@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Sogned-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Unify our shutdown/suspend/resume code and make it similar to e1000:
e1000_shutdown now calls suspend which does the exact same thing on
shutdown except saving PCI config state on suspend. WoL setup code
is now also more simple and works even when CONFIG_PM is not set, which
was previously broken.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Refine cb cleaning debug printout and print out all cleaned cbs' status.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

We keep getting requests from people that think that this might be
an exploitable hole where we would overwrite 4 bytes in the netdev
struct if the pci name would exceed 15 characters. In reality this
will never happen but we fix it anyway.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

This update to the copyright header adds the mailinglist, and aligns it
with the kernel licensing as well as remove the offending 'all rights
reserved'.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

This patch removes accesses to the HDLC-internal data structures
from pc300 driver, thus enabling it to compile but breaking part
of its functionality.
Signed-off-by: NKrzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch enables building of individual WAN protocol support
routines (parts of generic HDLC) as separate modules.
All protocol-private definitions are moved from hdlc.h file
to protocol drivers. User-space interface and interface
between generic HDLC and underlying low-level HDLC drivers
are unchanged.
Signed-off-by: NKrzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

le32_to_cpu() on 64bit values
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

	At enslavement time, the primary slave might not be activated if
there is already an active slave and the new slave is the primary.
Replaced complicated logic with a call to bond_select_active_slave(),
which does the right thing.

	Fixes http://bugzilla.kernel.org/show_bug.cgi?id=6378Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

	Fixed handling of 802.3ad LACPDUs.  Do not byte swap data in
place in the packet.  Updated nomenclature of "__ntohs_lacpdu" to be
"htons"; it was previously used for both ntohs and htons operations, but
only called ntohs functions.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

	Add logic to check ARP request / reply packets used for ARP
monitor link integrity checking.

	The current method simply examines the slave device to see if it
has sent and received traffic; this can be fooled by extraneous traffic.
For example, if multiple hosts running bonding are behind a common
switch, the probe traffic from the multiple instances of bonding will
update the tx/rx times on each other's slave devices.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

When a bonding netdevice is admin-ed down it loses the slaves
attributes (set via ifenslave). This is not consistent with other
behavior of netdevices (example a qdisc attached to a netdevice doesnt
disappear or an attached IP address etc).
The included patch fixes this. Ive tested by ifenslaving, downing the
bond, checking /proc and making sure it still has the slaves, up-ing the
bond and making sure things continue to work.

Jay/Bonding folks if you are ok with it, just ACK it or include it in
your tree etc. Otherwise we can discuss.
Acked-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add priv_flag to specifically identify bonding-involved devices.  Needed
because IFF_MASTER is an unreliable identifier (vlan interfaces above bonding
will inherit IFF_MASTER).  Misidentification of devices would cause
notifier events for other devices to be erroneously processed by bonding,
causing various havoc.

Bug discovered by Martin Papik <martin.papik@ipsec.info>; this patch is
modified from his original.
Signed-off-by: NMartin Papik <martin.papik@ipsec.info>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The bonding driver fails to adjust its hard_header_len when enslaving
interfaces.  Whenever an interface with a hard_header_len greater than the
ETH_HLEN default is enslaved, the potential for an oops exists, and if the
oops happens while responding to an arp request, for example, the system
panics.  GIANFAR devices may use an extended hard_header for VLAN or
hardware checksumming.  Enslaving such a device and then transmitting over
it causes a kernel panic.

Patch modified from submitter's original, but submitter agreed with this
patch in private email.
Signed-off-by: NMark Huth <mhuth@mvista.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Remove unneeded test for NULL.  Reported by Thomas Dillig
<tdillig@stanford.edu> and Isil Dillig <isil@stanford.edu> via Stephen
Hemminger <shemminger@osdl.org>.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Though link_failure_count is type unsigned int, this value is outputted to
/proc/net/bonding/bondX file using "%d" instead of "%u".

The attached patch fixes this problem.
Signed-off-by: NKenzo Iwami <k-iwami@cj.jp.nec.com>
Acked-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The value of "downdelay/miimon" and "updelay/miimon" are stored in
slave->delay. The type of downdelay, updelay, and miimon are all int.
However, slave->delay is type short, and it is not possible to store the
value of "downdelay/miimon" or "updelay/miimon" in some cases. (For example,
miimon=1 downdelay=32768)

The attached patch fixes this problem.
Signed-off-by: NKenzo Iwami <k-iwami@cj.jp.nec.com>
Acked-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Allow channel bonding to enslave a 10 Gig adapter without errors.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Acked-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Noticed by Yoichi Yuasa.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add support for older fiber versions of the SysKonnect board. These chipsets
use an internal PHY so they require special handling. The older sk98lin
driver already supported these
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

There seems to be a possible NULL pointer deref bug in
drivers/net/forcedeth.c::nv_loopback_test().  If dev_alloc_skb() fails, the
next line will call skb_put() with a NULL first argument which it'll then
try to deref - kaboom: a NULL pointer deref.  Found by coverity (#1337).
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Stephen Hemminger <shemminger@osdl.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

While checking gcc 4.1 -Wextra warnings, I stumbled across the following
two warnings:

drivers/net/phy/phy_device.c:528: warning: comparison of unsigned expression < 0 is always false
drivers/net/phy/phy_device.c:546: warning: comparison of unsigned expression < 0 is always false

Since phy_read() returns an integer and can return negative values, it seems
to me the best way to get proper error handling working again is to make val
an int.  Currently it is an u32, so the < 0 check always fails.
Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NMichal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NMichal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NMichal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NMichal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Jes Sorensen <jes@trained-monkey.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

We need to specify a Versatile-specific SMC_IRQ_FLAGS value or the new
generic IRQ layer will complain thusly:

No IRQF_TRIGGER set_type function for IRQ 25 (<NULL>)
Signed-off-by: NDeepak Saxena <dsaxena@plexity.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Nicolas Pitre <nico@cam.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>