Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 13 9月, 2014 1 次提交
  3. 06 9月, 2014 3 次提交
  5. 02 9月, 2014 1 次提交
    • W
      sock: deduplicate errqueue dequeue · 364a9e93
      由 Willem de Bruijn 提交于 
      sk->sk_error_queue is dequeued in four locations. All share the
exact same logic. Deduplicate.

Also collapse the two critical sections for dequeue (at the top of
the recv handler) and signal (at the bottom).

This moves signal generation for the next packet forward, which should
be harmless.

It also changes the behavior if the recv handler exits early with an
error. Previously, a signal for follow-up packets on the errqueue
would then not be scheduled. The new behavior, to always signal, is
arguably a bug fix.

For rxrpc, the change causes the same function to be called repeatedly
for each queued packet (because the recv handler == sk_error_report).
It is likely that all packets will fail for the same reason (e.g.,
memory exhaustion).

This code runs without sk_lock held, so it is not safe to trust that
sk->sk_err is immutable inbetween releasing q->lock and the subsequent
test. Introduce int err just to avoid this potential race.
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      364a9e93
  7. 12 8月, 2014 1 次提交
    • V
      net: Always untag vlan-tagged traffic on input. · 0d5501c1
      由 Vlad Yasevich 提交于 
      Currently the functionality to untag traffic on input resides
as part of the vlan module and is build only when VLAN support
is enabled in the kernel.  When VLAN is disabled, the function
vlan_untag() turns into a stub and doesn't really untag the
packets.  This seems to create an interesting interaction
between VMs supporting checksum offloading and some network drivers.

There are some drivers that do not allow the user to change
tx-vlan-offload feature of the driver.  These drivers also seem
to assume that any VLAN-tagged traffic they transmit will
have the vlan information in the vlan_tci and not in the vlan
header already in the skb.  When transmitting skbs that already
have tagged data with partial checksum set, the checksum doesn't
appear to be updated correctly by the card thus resulting in a
failure to establish TCP connections.

The following is a packet trace taken on the receiver where a
sender is a VM with a VLAN configued.  The host VM is running on
doest not have VLAN support and the outging interface on the
host is tg3:
10:12:43.503055 52:54:00:ae:42:3f > 28:d2:44:7d:c2:de, ethertype 802.1Q
(0x8100), length 78: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 27243,
offset 0, flags [DF], proto TCP (6), length 60)
    10.0.100.1.58545 > 10.0.100.10.ircu-2: Flags [S], cksum 0xdc39 (incorrect
-> 0x48d9), seq 1069378582, win 29200, options [mss 1460,sackOK,TS val
4294837885 ecr 0,nop,wscale 7], length 0
10:12:44.505556 52:54:00:ae:42:3f > 28:d2:44:7d:c2:de, ethertype 802.1Q
(0x8100), length 78: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 27244,
offset 0, flags [DF], proto TCP (6), length 60)
    10.0.100.1.58545 > 10.0.100.10.ircu-2: Flags [S], cksum 0xdc39 (incorrect
-> 0x44ee), seq 1069378582, win 29200, options [mss 1460,sackOK,TS val
4294838888 ecr 0,nop,wscale 7], length 0

This connection finally times out.

I've only access to the TG3 hardware in this configuration thus have
only tested this with TG3 driver.  There are a lot of other drivers
that do not permit user changes to vlan acceleration features, and
I don't know if they all suffere from a similar issue.

The patch attempt to fix this another way.  It moves the vlan header
stipping code out of the vlan module and always builds it into the
kernel network core.  This way, even if vlan is not supported on
a virtualizatoin host, the virtual machines running on top of such
host will still work with VLANs enabled.

CC: Patrick McHardy <kaber@trash.net>
CC: Nithin Nayak Sujir <nsujir@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: NVladislav Yasevich <vyasevic@redhat.com>
Acked-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      0d5501c1
  9. 06 8月, 2014 4 次提交
    • W
      net-timestamp: TCP timestamping · 4ed2d765
      由 Willem de Bruijn 提交于 
      TCP timestamping extends SO_TIMESTAMPING to bytestreams.

Bytestreams do not have a 1:1 relationship between send() buffers and
network packets. The feature interprets a send call on a bytestream as
a request for a timestamp for the last byte in that send() buffer.

The choice corresponds to a request for a timestamp when all bytes in
the buffer have been sent. That assumption depends on in-order kernel
transmission. This is the common case. That said, it is possible to
construct a traffic shaping tree that would result in reordering.
The guarantee is strong, then, but not ironclad.

This implementation supports send and sendpages (splice). GSO replaces
one large packet with multiple smaller packets. This patch also copies
the option into the correct smaller packet.

This patch does not yet support timestamping on data in an initial TCP
Fast Open SYN, because that takes a very different data path.

If ID generation in ee_data is enabled, bytestream timestamps return a
byte offset, instead of the packet counter for datagrams.

The implementation supports a single timestamp per packet. It silenty
replaces requests for previous timestamps. To avoid missing tstamps,
flush the tcp queue by disabling Nagle, cork and autocork. Missing
tstamps can be detected by offset when the ee_data ID is enabled.

Implementation details:

- On GSO, the timestamping code can be included in the main loop. I
moved it into its own loop to reduce the impact on the common case
to a single branch.

- To avoid leaking the absolute seqno to userspace, the offset
returned in ee_data must always be relative. It is an offset between
an skb and sk field. The first is always set (also for GSO & ACK).
The second must also never be uninitialized. Only allow the ID
option on sockets in the ESTABLISHED state, for which the seqno
is available. Never reset it to zero (instead, move it to the
current seqno when reenabling the option).
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4ed2d765
    • W
      net-timestamp: SCHED timestamp on entering packet scheduler · e7fd2885
      由 Willem de Bruijn 提交于 
      Kernel transmit latency is often incurred in the packet scheduler.
Introduce a new timestamp on transmission just before entering the
scheduler. When data travels through multiple devices (bonding,
tunneling, ...) each device will export an individual timestamp.
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      e7fd2885
    • W
      net-timestamp: add key to disambiguate concurrent datagrams · 09c2d251
      由 Willem de Bruijn 提交于 
      Datagrams timestamped on transmission can coexist in the kernel stack
and be reordered in packet scheduling. When reading looped datagrams
from the socket error queue it is not always possible to unique
correlate looped data with original send() call (for application
level retransmits). Even if possible, it may be expensive and complex,
requiring packet inspection.

Introduce a data-independent ID mechanism to associate timestamps with
send calls. Pass an ID alongside the timestamp in field ee_data of
sock_extended_err.

The ID is a simple 32 bit unsigned int that is associated with the
socket and incremented on each send() call for which software tx
timestamp generation is enabled.

The feature is enabled only if SOF_TIMESTAMPING_OPT_ID is set, to
avoid changing ee_data for existing applications that expect it 0.
The counter is reset each time the flag is reenabled. Reenabling
does not change the ID of already submitted data. It is possible
to receive out of order IDs if the timestamp stream is not quiesced
first.
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      09c2d251
    • W
      net-timestamp: extend SCM_TIMESTAMPING ancillary data struct · f24b9be5
      由 Willem de Bruijn 提交于 
      Applications that request kernel tx timestamps with SO_TIMESTAMPING
read timestamps as recvmsg() ancillary data. The response is defined
implicitly as timespec[3].

1) define struct scm_timestamping explicitly and

2) add support for new tstamp types. On tx, scm_timestamping always
   accompanies a sock_extended_err. Define previously unused field
   ee_info to signal the type of ts[0]. Introduce SCM_TSTAMP_SND to
   define the existing behavior.

The reception path is not modified. On rx, no struct similar to
sock_extended_err is passed along with SCM_TIMESTAMPING.
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      f24b9be5
  11. 01 8月, 2014 1 次提交
    • V
      net: Correctly set segment mac_len in skb_segment(). · fcdfe3a7
      由 Vlad Yasevich 提交于 
      When performing segmentation, the mac_len value is copied right
out of the original skb.  However, this value is not always set correctly
(like when the packet is VLAN-tagged) and we'll end up copying a bad
value.

One way to demonstrate this is to configure a VM which tags
packets internally and turn off VLAN acceleration on the forwarding
bridge port.  The packets show up corrupt like this:
16:18:24.985548 52:54:00:ab:be:25 > 52:54:00:26:ce:a3, ethertype 802.1Q
(0x8100), length 1518: vlan 100, p 0, ethertype 0x05e0,
        0x0000:  8cdb 1c7c 8cdb 0064 4006 b59d 0a00 6402 ...|...d@.....d.
        0x0010:  0a00 6401 9e0d b441 0a5e 64ec 0330 14fa ..d....A.^d..0..
        0x0020:  29e3 01c9 f871 0000 0101 080a 000a e833)....q.........3
        0x0030:  000f 8c75 6e65 7470 6572 6600 6e65 7470 ...unetperf.netp
        0x0040:  6572 6600 6e65 7470 6572 6600 6e65 7470 erf.netperf.netp
        0x0050:  6572 6600 6e65 7470 6572 6600 6e65 7470 erf.netperf.netp
        0x0060:  6572 6600 6e65 7470 6572 6600 6e65 7470 erf.netperf.netp
        ...

This also leads to awful throughput as GSO packets are dropped and
cause retransmissions.

The solution is to set the mac_len using the values already available
in then new skb.  We've already adjusted all of the header offset, so we
might as well correctly figure out the mac_len using skb_reset_mac_len().
After this change, packets are segmented correctly and performance
is restored.

CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      fcdfe3a7
  13. 26 6月, 2014 1 次提交
  15. 15 6月, 2014 1 次提交
    • T
      net: Fix save software checksum complete · 46fb51eb
      由 Tom Herbert 提交于 
      Geert reported issues regarding checksum complete and UDP.
The logic introduced in commit 7e3cead5
("net: Save software checksum complete") is not correct.

This patch:
1) Restores code in __skb_checksum_complete_header except for setting
   CHECKSUM_UNNECESSARY. This function may be calculating checksum on
   something less than skb->len.
2) Adds saving checksum to __skb_checksum_complete. The full packet
   checksum 0..skb->len is calculated without adding in pseudo header.
   This value is saved in skb->csum and then the pseudo header is added
   to that to derive the checksum for validation.
3) In both __skb_checksum_complete_header and __skb_checksum_complete,
   set skb->csum_valid to whether checksum of zero was computed. This
   allows skb_csum_unnecessary to return true without changing to
   CHECKSUM_UNNECESSARY which was done previously.
4) Copy new csum related bits in __copy_skb_header.
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      46fb51eb
  17. 12 6月, 2014 1 次提交
    • O
      net: add __pskb_copy_fclone and pskb_copy_for_clone · bad93e9d
      由 Octavian Purdila 提交于 
      There are several instances where a pskb_copy or __pskb_copy is
immediately followed by an skb_clone.

Add a couple of new functions to allow the copy skb to be allocated
from the fclone cache and thus speed up subsequent skb_clone calls.

Cc: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Marek Lindner <mareklindner@neomailbox.ch>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Antonio Quartulli <antonio@meshcoding.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Arvid Brodin <arvid.brodin@alten.se>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Allan Stephens <allan.stephens@windriver.com>
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: NChristoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: NOctavian Purdila <octavian.purdila@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      bad93e9d
  19. 11 6月, 2014 1 次提交
    • W
      net: fix UDP tunnel GSO of frag_list GRO packets · 5882a07c
      由 Wei-Chun Chao 提交于 
      This patch fixes a kernel BUG_ON in skb_segment. It is hit when
testing two VMs on openvswitch with one VM acting as VXLAN gateway.

During VXLAN packet GSO, skb_segment is called with skb->data
pointing to inner TCP payload. skb_segment calls skb_network_protocol
to retrieve the inner protocol. skb_network_protocol actually expects
skb->data to point to MAC and it calls pskb_may_pull with ETH_HLEN.
This ends up pulling in ETH_HLEN data from header tail. As a result,
pskb_trim logic is skipped and BUG_ON is hit later.

Move skb_push in front of skb_network_protocol so that skb->data
lines up properly.

kernel BUG at net/core/skbuff.c:2999!
Call Trace:
[<ffffffff816ac412>] tcp_gso_segment+0x122/0x410
[<ffffffff816bc74c>] inet_gso_segment+0x13c/0x390
[<ffffffff8164b39b>] skb_mac_gso_segment+0x9b/0x170
[<ffffffff816b3658>] skb_udp_tunnel_segment+0xd8/0x390
[<ffffffff816b3c00>] udp4_ufo_fragment+0x120/0x140
[<ffffffff816bc74c>] inet_gso_segment+0x13c/0x390
[<ffffffff8109d742>] ? default_wake_function+0x12/0x20
[<ffffffff8164b39b>] skb_mac_gso_segment+0x9b/0x170
[<ffffffff8164b4d0>] __skb_gso_segment+0x60/0xc0
[<ffffffff8164b6b3>] dev_hard_start_xmit+0x183/0x550
[<ffffffff8166c91e>] sch_direct_xmit+0xfe/0x1d0
[<ffffffff8164bc94>] __dev_queue_xmit+0x214/0x4f0
[<ffffffff8164bf90>] dev_queue_xmit+0x10/0x20
[<ffffffff81687edb>] ip_finish_output+0x66b/0x890
[<ffffffff81688a58>] ip_output+0x58/0x90
[<ffffffff816c628f>] ? fib_table_lookup+0x29f/0x350
[<ffffffff816881c9>] ip_local_out_sk+0x39/0x50
[<ffffffff816cbfad>] iptunnel_xmit+0x10d/0x130
[<ffffffffa0212200>] vxlan_xmit_skb+0x1d0/0x330 [vxlan]
[<ffffffffa02a3919>] vxlan_tnl_send+0x129/0x1a0 [openvswitch]
[<ffffffffa02a2cd6>] ovs_vport_send+0x26/0xa0 [openvswitch]
[<ffffffffa029931e>] do_output+0x2e/0x50 [openvswitch]
Signed-off-by: NWei-Chun Chao <weichunc@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      5882a07c
  21. 05 6月, 2014 1 次提交
    • T
      net: Support for multiple checksums with gso · 7e2b10c1
      由 Tom Herbert 提交于 
      When creating a GSO packet segment we may need to set more than
one checksum in the packet (for instance a TCP checksum and
UDP checksum for VXLAN encapsulation). To be efficient, we want
to do checksum calculation for any part of the packet at most once.

This patch adds csum_start offset to skb_gso_cb. This tracks the
starting offset for skb->csum which is initially set in skb_segment.
When a protocol needs to compute a transport checksum it calls
gso_make_checksum which computes the checksum value from the start
of transport header to csum_start and then adds in skb->csum to get
the full checksum. skb->csum and csum_start are then updated to reflect
the checksum of the resultant packet starting from the transport header.

This patch also adds a flag to skbuff, encap_hdr_csum, which is set
in *gso_segment fucntions to indicate that a tunnel protocol needs
checksum calculation
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      7e2b10c1
  23. 17 5月, 2014 1 次提交
  25. 13 5月, 2014 1 次提交
  27. 12 4月, 2014 1 次提交
    • D
      net: Fix use after free by removing length arg from sk_data_ready callbacks. · 676d2369
      由 David S. Miller 提交于 
      Several spots in the kernel perform a sequence like:

	skb_queue_tail(&sk->s_receive_queue, skb);
	sk->sk_data_ready(sk, skb->len);

But at the moment we place the SKB onto the socket receive queue it
can be consumed and freed up.  So this skb->len access is potentially
to freed up memory.

Furthermore, the skb->len can be modified by the consumer so it is
possible that the value isn't accurate.

And finally, no actual implementation of this callback actually uses
the length argument.  And since nobody actually cared about it's
value, lots of call sites pass arbitrary values in such as '0' and
even '1'.

So just remove the length argument from the callback, that way there
is no confusion whatsoever and all of these use-after-free cases get
fixed as a side effect.

Based upon a patch by Eric Dumazet and his suggestion to audit this
issue tree-wide.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      676d2369
  29. 11 4月, 2014 1 次提交
  31. 29 3月, 2014 1 次提交
    • V
      net: Account for all vlan headers in skb_mac_gso_segment · 53d6471c
      由 Vlad Yasevich 提交于 
      skb_network_protocol() already accounts for multiple vlan
headers that may be present in the skb.  However, skb_mac_gso_segment()
doesn't know anything about it and assumes that skb->mac_len
is set correctly to skip all mac headers.  That may not
always be the case.  If we are simply forwarding the packet (via
bridge or macvtap), all vlan headers may not be accounted for.

A simple solution is to allow skb_network_protocol to return
the vlan depth it has calculated.  This way skb_mac_gso_segment
will correctly skip all mac headers.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      53d6471c
  33. 28 3月, 2014 1 次提交
  35. 14 3月, 2014 1 次提交
  37. 12 3月, 2014 5 次提交
  39. 17 2月, 2014 1 次提交
  41. 12 2月, 2014 1 次提交
  43. 29 1月, 2014 1 次提交
  45. 27 1月, 2014 1 次提交
  47. 23 1月, 2014 1 次提交
    • M
      fuse: fix pipe_buf_operations · 28a625cb
      由 Miklos Szeredi 提交于 
      Having this struct in module memory could Oops when if the module is
unloaded while the buffer still persists in a pipe.

Since sock_pipe_buf_ops is essentially the same as fuse_dev_pipe_buf_steal
merge them into nosteal_pipe_buf_ops (this is the same as
default_pipe_buf_ops except stealing the page from the buffer is not
allowed).
Reported-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NMiklos Szeredi <mszeredi@suse.cz>
Cc: stable@vger.kernel.org
      28a625cb
  49. 15 1月, 2014 1 次提交
    • P
      net: add skb_checksum_setup · ed1f50c3
      由 Paul Durrant 提交于 
      This patch adds a function to set up the partial checksum offset for IP
packets (and optionally re-calculate the pseudo-header checksum) into the
core network code.
The implementation was previously private and duplicated between xen-netback
and xen-netfront, however it is not xen-specific and is potentially useful
to any network driver.
Signed-off-by: NPaul Durrant <paul.durrant@citrix.com>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ed1f50c3
  51. 07 1月, 2014 1 次提交
  53. 22 12月, 2013 1 次提交
  55. 18 12月, 2013 1 次提交
  57. 06 12月, 2013 1 次提交
  59. 22 11月, 2013 1 次提交
  61. 11 11月, 2013 1 次提交
    • J
      netfilter: push reasm skb through instead of original frag skbs · 6aafeef0
      由 Jiri Pirko 提交于 
      Pushing original fragments through causes several problems. For example
for matching, frags may not be matched correctly. Take following
example:

<example>
On HOSTA do:
ip6tables -I INPUT -p icmpv6 -j DROP
ip6tables -I INPUT -p icmpv6 -m icmp6 --icmpv6-type 128 -j ACCEPT

and on HOSTB you do:
ping6 HOSTA -s2000    (MTU is 1500)

Incoming echo requests will be filtered out on HOSTA. This issue does
not occur with smaller packets than MTU (where fragmentation does not happen)
</example>

As was discussed previously, the only correct solution seems to be to use
reassembled skb instead of separete frags. Doing this has positive side
effects in reducing sk_buff by one pointer (nfct_reasm) and also the reams
dances in ipvs and conntrack can be removed.

Future plan is to remove net/ipv6/netfilter/nf_conntrack_reasm.c
entirely and use code in net/ipv6/reassembly.c instead.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NJulian Anastasov <ja@ssi.bg>
Signed-off-by: NMarcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      6aafeef0