Kernel 2.6.18 broke the MotU Fastlane, which uses duplicate endpoint
numbers in a manner that is not only illegal but also confuses the
kernel's endpoint descriptor caching mechanism.  To work around this, we
have to add a separate usb_set_interface() call to guide the USB core to
the correct descriptors.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Reported-and-tested-by: NDavid Fries <david@fries.net>
Cc: <stable@kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

To enable periods shorter than 1 ms, we have to make sure that short
periods are only available for alternate settings that have a small
enough data packet interval.  Furthermore, the code that aligns URBs to
USB frames is now superfluous.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The data packet interval needs to be available in the audioformat
structure, together with the other audio format parameters, so that it
can be used to influence ALSA hardware parameters.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This removes the check_hw_params_convention() function because
1) it is not necessary, as the hw_rule_* functions also work correctly
   (i.e., as no-ops) when the device supports all combinations of the
   audio format parameters; and
2) it would become too complex when adding a fourth altsetting-dependent
   hardware parameter, as this would require another three loops to
   check dependecies with rate/channels/format.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When listing the device's sample formats in the stream? proc file, the
sample format number itself is rather obscure, so we better show the
format width, too.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When checking for the maximum queue length, we have to take into account
that MAX_QUEUE is measured in milliseconds (i.e., frames) while the unit
of urb_packs is whatever data packet interval the device uses (possibly
less than one frame when using high speed devices).
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When storing the channel numbers used by a format, and if the device
happens to support 32 channels, the code would try to store 1<<32 in
a 32-bit value.

Since no valid format can have zero channels, we can use 1<<(channels-1)
instead of 1<<channels so that all the channel numbers that we test for
fit into 32 bits.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Remove the MIN_PACKS_URB symbol because other limits can force the
number of packets down to one, regardless of the value of this symbol,
and nobody has ever changed it anyway.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The CM6207 incorrectly advertises its 96 kHz playback setting as 48 kHz
in its USB device descriptor. This patch extends an existing workaround
in usbaudio.c to also cover the CM6207.

This resolves issue 0004249 in the ALSA bug tracker.
Signed-off-by: NJoris van Rantwijk <jorispubl@xs4all.nl>
Cc: <stable@kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The detection of non-continuous rates (given via rate tables) isn't
processed properly (e.g. for type II).

This patch fixes and simplifies the detection code.
Tested-by: NJoris van Rantwijk <jorispubl@xs4all.nl>
Cc: <stable@kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

For audio devices that do not have proper audio descriptors (e.g.,
Edirol UA-20), we use hardcoded parameters from our quirks list.
However, we must still read the maximum packet size from the standard
endpoint descriptor; otherwise, we might use packets that are too big
and therefore rejected by the USB core.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Rather use printf format instead of hardcoding prefix like 0x.
A next step would be to predefine certain formats.
Signed-off-by: NAndreas Bergmeier <lcid-fire@gmx.net>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Distribute the packets evenly among the URBs, instead of making all URBs
except the last one to have the maximum size.  This makes the timing of
pointer updates more regular and removes some special cases from the
code.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Once our URBs contain enough packets, queueing more URBs does not give
us any additional underrun protection (as we use double-buffering) but
just increases latency unnecessarily.  Therefore, we try to limit the
queue length to some reasonable value.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When sending a silence URB (before playback has started, or when it is
paused), use the number of frames that would be normally sent instead of
a single frame so that the rate at which completion interrupts arrive is
consistent.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Convert from snd_card_new() to the new snd_card_create() function
in other sound subdirectories.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Use the USB functions usb_get_intfdata and usb_set_intfdata instead of
dev_get_drvdata and dev_set_drvdata, respectively.

The semantic patch that makes this change for the usb_get_intfdata case is
as follows: (http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@header@
@@

#include <linux/usb.h>

@same depends on header@
position p;
@@

usb_get_intfdata@p(...) { ... }

@depends on header@
position _p!=same.p;
identifier _f;
struct usb_interface*intf;
@@

_f@_p(...) { <+...
- dev_get_drvdata(&intf->dev)
+ usb_get_intfdata(intf)
...+> }
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The MIDI interfaces have to be detected dynamically for Edirol devices
ua-700, ua-25 and ua4-fx. This patch reverses the wrong changes made by
my other patch in uaxx-quirk.
Signed-off-by: NPedro Lopez-Cabanillas <pedro.lopez.cabanillas@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Renamed the old quirk function for ua-700/ua-25 to become more
generic, moving the MIDI interfaces to the quirk data header.
Added a new quirk for the Edirol UA-4FX.
Signed-off-by: NPedro Lopez-Cabanillas <pedro.lopez.cabanillas@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Add support for the E-Mu "Tracker Pre" USB sound card, following
the example of the (very similar) E-Mu 0202 and E-Mu 0404 USB.

As with the 0202 and 0404 USB, functionality is very limited:
just a couple of sample rates, no volume/mute control, etc.
Signed-off-by: NEran Tromer <eran@tromer.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Added the ignore_ctl_error parameter to enable/disable the control-error
handling for mixer interfaces.  It was a hard-coded ifdef, and now you
can change it more easily.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Kill snd_assert() in other places, either removed or replaced with
if () with snd_BUG_ON().
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Since USB_EHCI_SPLIT_ISO is now unconditionally enabled the
#ifndef CONFIG_USB_EHCI_SPLIT_ISO became wrong.
Reported-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fix the race at reconnection of the device.
The disconnected usb_chip[] must be cleared before the next probe
call properly.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Putting space between ! and variable is a strange coding style, fix
that, also make it fit into 80 columns where that is easy.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

usb audio contains useful  debugging code, protected by #if
0. Unfortunately, it will not compile because variable names changed;
fix it.

Dallas workaround is formatted in a way where it is not quite obvious
what is normal code and what is quirk. Reformat it to make it obvious.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Dallas USB speakers are buggy in more than one way. One of configs
they offer does not work at all.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The error in check_hw_params_convention() has to be checked and
handled properly.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

sound/usb/usbaudio.c (check_hw_params_convention): Handle kcalloc failure.
Signed-off-by: NJim Meyering <meyering@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add a workaround for the feedback pipe of E-Mu 0202/0404 USB devices
that reports the number of samples per packet instead of the number of
samples per microframe.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This header file exists only for some hacks to adapt alsa-driver
tree.  It's useless for building in the kernel.  Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it.  This should be really killed in
future.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

sound/usb/usbaudio.c: In function 'usb_audio_suspend':
sound/usb/usbaudio.c:3674: error: implicit declaration of function 'snd_pcm_sus\pend_all'
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

This patch implements suspend/resume support for USB audio devices.
It works with the microphone in my camera.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

usb_set_interface() can fail, even for altsetting 0
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Allow low speed MIDI devices because newer devices from ESI do not
support full speed.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Add a snd_pcm_rate_to_rate_bit() function to factor out common code used
by several drivers.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixed AC3 interface in device_setup=0x00 mode thanks to Hakan
Lennestal and updated documentation
Signed-off-by: NThibault Le Meur <Thibault.LeMeur@supelec.fr>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Audiophile-usb fix (corrects little-endianness in 16bit
modes, resets interfaces at device initialization, and updates the
documentation).
Signed-off-by: NThibault Le Meur <Thibault.LeMeur@supelec.fr>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>